How To Install TORS Delete Kit On BANSHEE Carbs

RE-DO Banshee - How To Install TORS Delete Kit On BANSHEE Carbs
Subscribe 👉 bit.ly/RedoBans...
REDO SHOP - redo-parts.com...
If you find this video helpful, make sure to drop a like & leave a comment down below!
➖➖➖➖➖➖➖➖➖
Subscribe 👉 bit.ly/RedoBans...
Extra keywords (don't pay attention):
How-to,Pack bearings,Stem bearings,Steering Stem,Bearings,Change,Replace,Replacement,Fix,Bad Bearing,Bad Steering,Remove,Removal,Motorcycle,Dirt Bike,Motocross,Steering,Stem,Needle Bearing,packing,Outer race,Inner race,Steering head,All balls,Pivot works,Redo Parts,Banshee,dirt bike,steering head bearings,replace steering bearings,adjust steering head bearings,repack steering head bearings,replace,motorcycle,repair

[@jasonbiedrzycki7197]

This video was very helpful, i just bought Chinese carbs and didn't know what to do abot it not having idol screws, going to use the screws from the old stock carbs and make it work, thanks

[@jaded804]

I just bought some rad valves off you guys keep up the good content

[@dawnhorn3949]

Awesome thank you!

[@stevemount483]

This is identical to a blaster tors delete kit. I have to take mine out and sand edges and the screw inlet. You should do a carb adjustment video with good explanation on how it all works.

[@raeesstemmet9656]

Thanks for the great vid

[@RedoBansheeParts]

Glad you enjoyed it

[@stone9882]

I’m doing this for my blaster.

[@dawnhorn3949]

Right on, works exactly the same

[@ivanvail928]

Was this performed on stock mikuni carbs?

[@Floridawoodsbanshee]

So unplug two wire plugs on the engine harness. And just leave them or cutting them off. Or do they need to be shorted together? I like how this was taught. Been wanting to do this. Just don't know what to do with the 2 wire plug connectors on wiring harness.

[@RedoBansheeParts]

You can just leave them. I would tape them into the wiring harness with some electrical tape.

[@jamie8954]

How many turns should the new idle screw be ?

[@RedoBansheeParts]

we start at 1 full turn out as a base and go from there depending on what the bike wants.

[@kelloggskelloggs6185]

Thank you for the video I have a 2005 banshee and we installed the tors delete kit, the banshee start in the first or second kick, but dont run, or run very weak. It’s necessary install a cdi and harness of 87-94 banshee? That’s what told me the mechanic.

[@RedoBansheeParts]

You need to properly test the stator before you just replace it. Give us a call at 541-419-6054 and we would be glad to walk you through some diagnosing

[@traviswagner9114]

I just bought an 87 banschee it has the tors delete but they did not install the idle screws. So how will this affect how it runs?

[@hbkjorden2254]

Without the idle screw it won’t idle most likely. So just drill out the hole and thread it so you can put your own idle screw in. It’s just so that the bike would idle by itself.

[@RedoBansheeParts]

If you don’t have idle screws it wont idle unless you raise the throttle cables by adjusting them at the lids. It can be done but it’s not ideal.

[@sambo6591]

I cannot seem to get it flat and even the surface it's decently flat but it is uneven Will it still work or should I just put my tors back on before I drill

[@RedoBansheeParts]

Give us a call so we can discuss this I'm having a hard time catching what step you are on. 541-419-6054

[@blakedahl-ek8bh]

I don't see any info on the electrical disconnect.... what wires get deleted during the tors delete?

[@RedoBansheeParts]

You don't have to delete any electrical simply unplug the tors control unit assembly that's bolted to the frame to the left of the ignition coil

[@blakedahl-ek8bh]

@Re-Do Banshee Parts and Accessories awesome thank you

[@marlongebara2634]

I need help with my banshee please. It was running okay, was thinking it needed a carb cleaning, I did that. When I put them back on, it would start on choke only after a lot of kicks and runs for a little then dies if I don’t keep my finger on the throttle. I watch a lot of your videos I follow some instructions but I can’t quite figure this out

[@RedoBansheeParts]

Make sure you didn't put the slides in the opposite carbs. It should have the slight opening facing the air filter side.

[@sambo6591]

After I did my tors delete I have rev hang

[@RedoBansheeParts]

It was nice speaking on the phone with you again give us a call if you have more issues.

[@blakeharder9880]

19:30 - 26:30

[@blakeharder9880]

Self note lol

[@RedoBansheeParts]

👍

[@RedoBansheeParts]

👍👍