How to: Install Toyota Pickup Truck LED Headlights - 4Runner & Tacoma too!

Today I upgrade the halogen sealed-beam headlights on my 1985 Toyota Pickup to LED replacements from TRUCKMALL. The factory headlights are a sealed beam design, which was standard on trucks and cars in 1985. When the light burned out or cracked, you threw away the whole light assembly and replaced it with another.
These LED Lights are a direct replacement for the factory Halogens, although I did have to buy an additional H4 Relay harness to make everything plug and play.
The LED lights on Amazon: amzn.to/3e1Kd1i
The harness for Toyota Pickup, 4Runner and Tacoma: amzn.to/3reHeWY
Here are some other Toyota videos you may find helpful:
How to Restore/Fix/Repair a Cracked Vinyl Dash: • How to Restore/Fix/Rep...
How to Remove 1980's Toyota Pickup/4Runner Dash Pad Cover: • How to: Remove 1980's ...
How to clean/Restore Toyota Pickup/4Runner Door Panels: • How to: Clean/Restore ...
Toyota Door Disassemble: • How To: Disassemble a ...
Rebuild front knuckle & replace birfield joint: • Toyota Solid Front Axl...
Remove an Entire Toyota Rear Axle Assembly: • How to Remove an Entir...
Install/Upgrade to V6 1" Master Cylinder on 4 cyl Toyota: • How to Install/Upgrade...
Install Toyota Rear Axle Bearing, Oil Seal - WITHOUT a Press: • Install Toyota Pickup/...
Replace Toyota Drive Shaft Center Support Carrier Bearing: • DIY: Toyota 4x4 Drive ...
Trail Gear Hi-Steer install: • Trail Gear Hi-Steer in...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Fixing Floor and Rocker panel rust: • Fixing Floor and Rocke...
Remove Headliner in Toyota Pickup Truck: • How to: Remove Headlin...
Remove Toyota Pickup & 4Runner COMPLETE Dash: • How To Remove Toyota P...
Toyota 22RE Engine Teardown: • $100 Toyota 22RE Engin...
22r Compression Test: • How to: Compression Te...
Remove Toyota 22RE Engine & Transmission: • Remove Toyota Pickup T...
Toyota Pickup/4Runner Vent Window Conversion: • How to: Toyota Pickup/...
Remove Toyota Truck Rear Glass Window: • How to Remove Toyota T...
Toyota 4x4 Transfer Case Rear Flange Oil Seal Replacement: • DIY: Toyota 4x4 Transf...
Replace Pinion Oil Seal in Rear Diff: • How to Replace Toyota ...
The Vent Window Conversion: • How to: Toyota Pickup/...
Remove Door Panel: • How to: Remove Toyota ...
LED Headlight Conversion: • How to: Install Toyota...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Breaking a Rusty Toyota Frame in Half: • Breaking & Cutting Up ...
Toyota Pickup Fiberglass Bed Review: • Toyota Pickup Truck Fi...
B-Pillar Trim Removal & Install: • Toyota Pickup/4Runner ...
I don't have Patreon or ask for donations but you can support the channel with some rad Yota gear from my store: 6thgeargarage.com/merchandise/
Follow Us:
Instagram: 6th_gear
6thGearGarage

[@KingCobra001.]

Thank you for the wiring problem, I am 16 years old, and I am in progress of restoring my brother's old 1996 toyota tacoma, and I bought LED lights for it, couldn't find the problem with the wiring until I stumbled upon you video, thank you!

[@6thGearGarage]

Glad to help!!

[@bob_frazier]

Incredible! Someone who doesn't edit out the errors, and instead turns the entire situation into something we can all learn from! Awesome. An instant subscribe from me anyway.

[@nancyc6236]

Figured out the hard way that I needed the H4 relay harness 😅 glad you recorded and posted this to make sure I wired everything up correctly.

[@christopherbarber288]

I just want to personally thank you for this video. I have a 1990 Toyota pick up that I just put some of these in. Went ahead and got the harness just to be safe, and sure enough it was needed! if it weren’t for you showing what was wrong I would’ve probably had an extremely difficult time figuring it out. Thank you so much! I love my new headlights so far. ♥️

[@applejaz]

Keep those Toyota vids coming please👍

[@mike325ci]

I actually really appreciate that you kept your "failed" first attempt at "plug and play" because that's EXACTLY what I experienced when I went to plug in my LED light. Same as you, I swapped the wiring around (actually tried many other combos too), but kept getting High Beams on all the time, and when flashing my high beams, it turned off... Then searched a bit and found that Toyotas are switched ground, and these lamps assume a more standard switched positive. So we need the relay wiring kit you ordered (or I guess you can wire it yourself, but for $18, the parts and time to do it is worth that much). Had I seen your video before I started this project, I would have known what to expect and saved some time, but oh well, it's always trial and error with these old Toyotas. BTW, my car is a 1986 MR2 (AW11), and I also have a 1988 Celica (ST165) and 1992 Celica (ST185): they all had the same issue - pretty safe to assume any old Toyotas with the H6054 7x6 headlights have the same wiring. P.S. Also got a good laugh about the rusted headlight ring retainer screw. Those damn things are always rusted on every Toyota I had and the Vise Grip method is my favorite method too!

[@ms_304]

Glad that even 2yrs ago you’re still helping people!! I’m going to do this for my ‘85 Toyota pickup!

[@octaviosuarez3511]

hey question how’d did that go i have an 86 pickup and it says the wiring harness is only for 88+ did you have any issues?

[@Imheem90]

Thank you for sharing! Purchased these for my dad with the harness after watching this video. Just installed them today and they made a world of a difference!

[@6thGearGarage]

Glad the video helped!

[@jackgray1402]

These are the exact same lights that I bought for my 93 Toyota Pickup. Thank you for the video.

[@kashoutcris9487]

Ayy bro i have a 93 pick up to. Did you have an issue with them just staying in high beams??

[@jackgray1402]

@@kashoutcris9487 No. Did you buy H4 harness for the head lights? I had a problem with getting the brights to come on, but that was caused by my switch, not the lights.

[@jimb4715]

I ordered some right after I watched your vid. I installed them and they work great. thanks for another great vid.

[@freshoneco.fishingandcampi6553]

Did the same

[@coltonmartin1072]

Thank you for making this video! I installed a set of these same lights I got on ebay last year in my 87 and had run into the same issue with mine which never came with the adapter or instructions.. so I only set up my low beams and was dragging my feet on the idea of having to rewire the factory switching. Now that I know about this adapter I wont have to! Otherwise I've been running these lights for a year and enjoy mine too

[@6thGearGarage]

Glad the vid could help someone else!

[@kerrymackey]

Just ordered the exact same setup for my 86' 4Runner... Thanks for the vid. Very helpful in making my decision.

[@jeffpitt3213]

Nice job on the video, funny thing, I got the exact same headlights before I saw your video for my lj78, the LC forum I belong to clued me into the relay harness so when I ordered the lights I did the relay, sometimes having an issue is a good learning experience especially when presented in a video format for learning, after all that’s what these are all about and to see a potential issue ahead of time is always a good thing. Once again, nice job!!

[@OhYeahAboutThat]

Headlight technology has come a long way!!

[@jacobbontkes536]

thank you very much sir, video was well done covering all the issues i would have encountered and saved me an afternoon of running my own relays

[@xXNightwing1Xx]

This was just what I was looking for! I’m in Hawaii and the salt eats my truck so watching you deal with something I might come across was really helpful! Thanks for showing everything

[@6thGearGarage]

Mahalo, I know rust all too well on these trucks!

[@benw.7974]

Hey man this helped me solve my problem. Just installed these day, thanks to your video.

[@WindyValleyAZ]

Beautiful truck! And exact problem I ran into with new led headlights, thanks for the solution!

[@Giroux68]

Thats cool. Next mod on my 1990. Just sound deadened my doors and lubed up the windows. What a difference.

[@ItsSpelledRJ]

Thank you for uploading this! It really helped me out. I lucked out and didn’t need to unscrew the metal frame around the headlight, I got new hologram ones and they came with it. All I need to do was remove the bolts that keep it in place and position it and a spring.

[@6thGearGarage]

Great to hear! Those tiny rusty screws were the worst part of it all.

[@braydenpapaila4719]

Life saver thank you very much for this. Was losing my mind. Never knew the headlight wiring was like that on my 91 4Runner

[@6thGearGarage]

Glad I could help! Toyota has left a lot of people scratching their heads on this.

[@iridiumnight3750]

Great tutorial thanks! Much more of a project than putting the lights in my s10.

[@xanny7373]

i bought this exact set before watching this video and had the same problem glad there’s a solution

[@juananaya5490]

What type of lights are those

[@Rumeel12708]

Thinking of buying these for my 94 pickup, amazing

[@6thGearGarage]

Worth every penny! Just make sure to get the harness too.

[@chiseledslinky1314]

I'm about to order these rightnow lol. My friends been doing upgrades to his jeep and i feel left out i havnt done much to my 84toyota pickup. Thanks for the vid!

[@brokenarrowmachine]

Awesome video couldn’t figure out the darn lights for the life of me. Thank you!

[@mickpaton9473]

Hello from 🇦🇺 I have a 1996 toyota hilux dual cab and will be doing the light upgrade soon. Thanks for video

[@wasd007]

Best truck ever.

[@theshazman]

Getting ready to do exactly this to my 88 Pickup :) Love your videos man.

[@6thGearGarage]

Thanks!!

[@theshazman]

@@6thGearGarage Just got it done yesterday and I couldnt be any happier. Only thing I need to do now that Ive installed the new headlights is I should have gotten a housing that supports DRL. So I may do a swap down the road if my friend is willing to take the existing ones off of my hands.

[@lilashilo]

very well presentation "in detail" awesome!! thank you very much!! Best to you!!

[@94turbotoy]

Nice video…definitely a big upgrade over the stock H6054 sealed beams. I also ran into the same issue when installing my JW Speaker 8900 H6054 LED headlights on my 1994 Toyota pickup. Toyota trucks use a double switched ground system which causes the issue since the LED’s headlights are designed to work with a switched positive system. After installing the H4 harness all worked perfectly. Light output is excellent with a very clean cut-off. High beams are insanely bright and usable! Yours came out great!👍🏻

[@caleb1424]

Did you keep the old headlight wiring system in the truck?

[@jeremylyerla5356]

Thanks for this just installed them in my 88 and works great.

[@6thGearGarage]

Great to hear!

[@kevinrobledo8768]

Exactly what I needed! 🙏🏼🙏🏼🙏🏼

[@King_wendigo99]

Happy I watched this video

[@jackenrod6794]

Excellent tutorial. I just bought the harness because my LEDs did the same. No HB. Just LB. THX

[@6thGearGarage]

Glad it helped👍

[@jackenrod6794]

@@6thGearGarage Installed in about an hour. Just like yours, i didn’t have a solid ground connection on the passenger side. A little finagling and lo and behold we’ve got Hi and Lo beams. I had to take the battery out to work on the right side. A minor PIA. I couldn’t have done it without your detailed explanation. Many many thanks.

[@JesseGunter]

Ahhh this was my exact problem. Thanks dude.

[@6thGearGarage]

Glad I could help!

[@vegaf2011]

Life saver 🙌🙌🙌 this video rules.

[@Mertesacker1]

Remember to aim them correctly for optimum lightning for you, and to not blind oncomming traffic.

[@doubl3l80]

I've got these same lights on both my Nissan hardbody trucks, and with the first click of the h/l switch, they go into DRL (daytime running light). Just the vertical LEDs on the sides light up, i think it looks dope!! They actually put out some light too, sometimes I forget to put my headlights on bc the DRLs are bright enough & i don't realize it Anyhow, Awesome video man. I appreciate how thorough you were!.

[@6thGearGarage]

Aren't they amazing? After driving with these at night, I don't think I could ever go back to the old halogen headlights.

[@JamesWeyhmiller-gf3cy]

Great video super helpful

[@lonewolfvlogix6335]

Good on ya mate. Keep em comming aye.

[@capeman10]

Good job on the lights. Just subscribed.

[@Tony-112]

Just found your video/channel , great video👍👍

[@davidcarr1262]

I watched this and instantly went out and got a pair for my sealed beam headlight car (1998 toyota hilux) im from australia haha

[@erikgaribaldi1227]

That has always been my dream truck since I was a kid

[@jcheney8779]

Was always mine too, bought an 86 Toyota pickup and had it for 6 years now. Still runs better and longer than any of my buddies trucks

[@erikgaribaldi1227]

@@jcheney8779 wow that's good..that truck I have is an 84 but I had another engine from an 83 put in it's a 22r.

[@erikgaribaldi1227]

@Shiloh Lopez how much I want for it

[@erikgaribaldi1227]

@Shiloh Lopez don't be like that don't sale it Buy yourself a cheap van and save that truck

[@shanevanbeek2694]

Got my 86 a couple years ago, best decision. Best camping truck hands down. Buy a 1st gen before there all destroyed it will be a great investment.

[@aerialrescuesolutions3277]

That was super funny and totally Kool. Thanks.

[@Mudmowerdiesel]

Awesome video thank you

[@brandonfletcher1667]

I appreciate your video, I was having the same issues. Find your video with the link to the harness, and it'll be out together this Friday. Thank you!

[@6thGearGarage]

Glad it helped

[@ttinnovations3310]

cool video, I have a 4x4 87 T, I need to do this asap

[@josealbizures1443]

Gracias! saludos de Guatemala :D

[@troypeplinski6241]

Omg thank you for this video, I was about to just roll with no high beams!!!

[@6thGearGarage]

Glad it could help!

[@troypeplinski6241]

@@6thGearGarage did you still have to use the wire adapter to switch the negative when installing the upgrade harness?

[@6thGearGarage]

@@troypeplinski6241 No I did not need that after installing the H4 relay harness

[@SOLDADITO76]

I got a set of Cibie lenses so when I loose a head light I just replace the bulb, and if I want brighter lights do the same thing as well.

[@josephlahood4647]

I remember those days. Screws always rusted in in New England salt here bad

[@ea95401]

this was super helpful!!!!!!!!!!!!1

[@6thGearGarage]

Glad it helped!

[@autocrow]

Good video. I went from using one, to using two H4 harnesses. The stock Toyota has redundancy (separate fuses for left and right). This setup only uses one Toyota fuse and has only one fuse going from the battery to both headlights. Either fuse blows and both headlights go out at the same time. With two harnesses, I'm using both Toyota fuses left and right, and now running separate fuses for left and right headlights from the battery. Interesting, the high beam indicator light on the dash didn't work with one harness, but now works with two. I simply cut off the part of the harness I was no longer using that went to the second headlight, capped off the exposed wire ends with small wire nuts and some electrical tape. I then added wire to the hot on one harness to reach across to the battery. I used the leftover wire and conduit to lengthen the hot and soldered and taped the connections on the hot. Then it's just plug and play. A good investment for only 17 dollars for the second harness. Much, much safer to have each side fused separate so you don't risk losing both headlights at once!

[@6thGearGarage]

That's a really good idea, thanks for sharing!!

[@autocrow]

@@6thGearGarage You're welcome. Glad you like my idea!

[@aentrekin35]

Loved it

[@6thGearGarage]

Thanks, I’m still running these lights…. Don’t think I’ll ever go back to halogens.

[@aentrekin35]

@@6thGearGarage Just installed on my 94 yesterday. Man, they are bright

[@phoneone1371]

great video , i went through the exact same problems on my 84 except rust because iam in nevada . once you go to LED theres no going back , the only drawback ive found is driving in snow the LEDs dont get as hot so snow builds up on them instead of melting off although i heard there now making heated LEDs

[@6thGearGarage]

I hadn't considered that. I try not to drive this one during winter so it won't rust away

[@adrianbooysen219]

SUBSCRIBED!!

[@ZombieTapdance]

Here for my Toyota supra lighting lol. Happens to be the exact same on my 87!

[@6thGearGarage]

Good to know Toyota was consistent!

[@shobud7561]

Theses would look great on my 83 Corolla Wagon.

[@williamneigum7002]

just got new lights today for my lowered 87

[@6thGearGarage]

The light output from these is amazing. Probably better for a lowered truck so you won't blind other drivers in a lifted truck.

[@bretbutler2521]

Hey the DRLs are the same as your park lights… if you want to run them on new headlights tap into park lights!

[@dannybuilding1044]

loyal Yoda gang here considered me a fan., so I subscribe. that ryhmed

[@brianeighties4481]

I bought a kit with the many led lights for my 84 Toyota and was very frustrated my brights wouldn’t work. I bough a wiring kit from somewhere out west similar to the one you bought and plugged it up the same way. Still didn’t work. It was a waste of 50 bucks. I hardwired a toggle switch to turn on my brights. I’m really disappointed and am looking for some nice good old fashioned bright halogens now. Glad your stuff worked mine was a waste.

[@brianeighties4481]

Got the non working wiring harness from lowrangeoffroad.com

[@vvaldez0221]

Very nice truck, I love your DIY videos, you are the best. BTW what is the color code of the RED paint? I like it!

[@6thGearGarage]

Victor Valdez thanks!! The red is called Vermillion Red and it’s an oem color from an F-150.

[@ryangardner7709]

I’m about to do this swap

[@chrisdouglas3158]

The harness listed from amazon is currently out of stock. Know any other ones on Amazon that will work? I want to do this to my pickup as well! Thanks for the video/ tutorial! Love all your stuff so keep it coming!

[@6thGearGarage]

I would search for "H4 relay harness toyota" there are probably others available.

[@jdfield6160]

Great video and love the channel. Just installed the same LED headlights you used and also the relay harness. All worked except only have high beams. Cleaned grounds, no change. Unplugged new headlights and replugged in the old and now get high and low beams through the original headlights. Do you have any suggestions or ideas why the new lights only have high beams?

[@6thGearGarage]

Are your high beams on all the time when you turn the lights on, or do you mean you have no low beams and only high beams?

[@cyberhornthedragon]

just FYI if you still have the truck the H4 harness likely has saved your electrical system specifically the headlight knob and the wiring into the stem toyotas run all headlight power through the stem the relay harness fixes that part by the switch just operating a relay i have mine now operating 2 relays (using the non used headlight socket) so my offroad light bar does not work if im running high beams (which is illegal in some states) an if i cut off the lights all of them go off

[@6thGearGarage]

Good info, thanks for sharing!

[@BosleyBeats]

Thanks so much for doing this. I’m starting my modding adventure on an 89 Toyota pickup sr5. What do you suggest for forums to search for parts for the pickup? Also do you have any preferences for aftermarket accessories such as winches+bumper, led tail lights, etc? Thank you so much for knowledge and time you share with the community. #legend 👍🏾🔥

[@6thGearGarage]

I've never worked on the 89+ trucks, but I've bought parts from LCE, Low Range, Trail Gear, 22re performance - all good companies. Old Man Emu, Marlin Crawler are a couple more good ones. Just stay away from the cheap stuff made in china and you'll be good.

[@BosleyBeats]

6th Gear Garage you are my hero. Thank you! This helped immensely, I have a lot more ideas just browsing through these sites. 🙏🏾 You rock.

[@ravenfeather7087]

@@6thGearGarage Yep, keep adding all those crap after markets parts and you'll turn your Yota into a POS Ford-like vehicle. Nothing like screwing up the best made trucks on the planet.

[@TheRandomDead]

Aw darn. I was gonna say Ford Edge too but someone already said it lol. Maybe I need to be earlier

[@manuel13271]

There we go.... Thats weird lol 😆😅made me laugh I dont know why but imma get these for my dads 96 tacoma

[@primosport691]

I just bought some head lights with DRL on the edges for my 88 runner. could you make a vid on how to link those drl with the stock yellow drl's

[@6thGearGarage]

You'll need to splice into the factory wires for those lights. I didn't get those kind because I wanted to leave the original wiring alone in case I ever go back to stock.

[@johnstewart4564]

The dirty ground problem was the only problem I had.

[@BebasKai]

Hey, thanks for all the videos on your Toyota. I just got an 84 Toyota Pickup. I replaced the headlight with the TRUCKMALL brand like you did in this video Do you have a lot of people flashing their brights at you? Did you make any adjustments to the lights? What do you think of the lights after a year of use?

[@6thGearGarage]

So far no complaints but I am going to aim the lights a little lower because they’re so bright. Nobody has flashed me yet, but I don’t drive it at night very often.

[@BebasKai]

@@6thGearGarage I think I’ll do the same since I do a lot of night driving. Good luck with yours and thanks for the help.

[@ericlacambra3610]

I have a 1990 Toyota Hilux and I was wondering how do you keep the corner lights on while the main headlights are switched on as well? How did you wire it? Please lmk ASAP !! Thank you in advance

[@6thGearGarage]

That is how all of the US Toyota trucks of this generation come from the factory.

[@tylersteil3078]

Wassup man 2 years later still helping people out I got a question I have the same lights and new harness how could I order new relays

[@6thGearGarage]

You could try looking for a part # on the old relay and searching for that part online. If they aren't available then you may need to buy another harness.

[@tylersteil3078]

@@6thGearGarage not all hero’s wear capes we drive Toyota’s thanks man🤙🏽

[@lazibuilt]

Im pretty sure I followed your instructions and lights are working great. Only thing is... now my truck won’t start. Dash lights are on, power seems normal but it won’t turn over the starter which it sounds like. Any solution

[@6thGearGarage]

Are the battery terminals tightened all the way?

[@lucassurridge7563]

Those lights kinda look to modern for the truck. I’m more of a oem guy. Great video tho helped very much. Very good

[@6thGearGarage]

I'm with you, I love the classic look. The light output is so much better though, I feel more comfortable driving at night. Of course, I kept the glass lights in case I ever want to go back to OEM :)

[@colvinjonas1486]

Do you have any idea how to put a foglamp into the bumper of a 1989 Toyota 4runner sr5, any suggestions will be appreciated, thanks

[@6thGearGarage]

Sorry I don’t, I haven’t owned a 4Runner yet to learn on.

[@soyelfbi96]

@6th Gear Garage, I got these lights with the harness for my 1987 Toyota pickup. However one of the light seems to be brighter then the other as if it were a high beam, but when I do turn on the high beams it gets even brighter then the other. Any reason why this is happening?

[@6thGearGarage]

I would check grounds

[@dekotamaynard4220]

@6thgeargarage what did you bolt the relays too? Thanks for the help buddy

[@6thGearGarage]

I didn't bolt them, just zip tied them securely to the harness and tucked them in the space between the battery and the side of the engine bay.

[@dekotamaynard4220]

Thank you so much buddy. Think i could wrap the exposed metal with electrical tape​? @6thGearGarage

[@sidekikz]

any idea if this harness would work for an ‘88? also what lift kit do you have on your ‘85? thanks in advance, it’s hard to find info on these durable lil trucks!

[@6thGearGarage]

Yes, the harness will also work on an 88. This truck has a 4" Pro Comp lift, plus a 2" body lift.

[@floyd1986]

Can you do a video of the interior. The gauges peek my interest.

[@6thGearGarage]

Thanks, I'll work on an interior video

[@floyd1986]

@@6thGearGarage from a glance it looked pretty neat.

[@dairyjerry2455]

I did the exact same install on my truck except I used the harness from trail gear I think it was and I went with the three-row LED headlights. I watched your video and it was exactly the same thing for me. After I put the harness on though everything work good except all my gauges move with the blinker when my headlights are on as well as I can barely see the high-beam icon in my Dash. I talked to an automotive electrician who said he's pretty sure there must be power going out my ground and that I would need I think he said a transistor or something? I checked all my grounds are all nice and clean I'm stumped. Any suggestions?

[@6thGearGarage]

I was gonna say check the grounds but you already did. Im not sure what the problem could be.

[@TheBombcontrol]

Do you have a video on how to install headlights with Halos?

[@6thGearGarage]

No I don't, but I'm getting ready to upload how to install LED headlights with integrated turn signals. Similar but just a different wire to tap in to.

[@luisernestonolascoalfaro3693]

Do you know where can I found the wiring diagram couse in my country can't find the harness but we have the stuff to do it ...

[@6thGearGarage]

Yes I have them available on my website: 6thgeargarage.net/1985-toyota-pickup-truck-hilux-4runner-wiring-diagram/

[@theshazman]

Hey man, I just acquired an 88 Toyota Pickup and I'm looking to bring her back to her old glory. I really like your videos and those headlights especially caught my eye. I looked at the links you've posted and it looks like the Wiring Harness is no longer available. Amazon link is dead. Is there something in particular you need for these lights, could you point me towards another compatible harness? Greatly appreciate it from North Carolina.

[@6thGearGarage]

Vinyl thanks for the heads up! If you google “h4 headlight relay harness” you should get results for a lot of them from different companies. They all do the same thing, just be sure you get the full harness with relays and not just a pair of pigtail adapters.

[@theshazman]

Awesome, thanks for getting back to me. I grabbed just that harness with that set. Looking forward to installing them. I just installed a light bar that came with a nice relay harness and in-dash switch. Turns night time into daylight. Perfect for dark country roads at night. I absolutely love this truck!

[@poly-glot-a-lot6457]

I have a 1986 Toyota Mini-Cruiser RV. Do I need the harness?

[@6thGearGarage]

Yes I think you will need it.

[@poly-glot-a-lot6457]

@@6thGearGarage thank you for your quick response

[@ScoobyDJ.]

Did you paint your indicator lights and grill yourself? What paint did you use?

[@6thGearGarage]

I used duplicolor black trim paint on the grill and around the edge of the lights.

[@maxmaldonado4155]

Have the same lights on a 1989 Toyota pickup truck and when I would turn the lights on they would flicker and turn off then I would turn then off and on again And they would come on. Now they don’t turn on just the high beams come on. Do you think it could be a wiring issue or the light burnt out ? Both side had gone out

[@6thGearGarage]

I’d check the grounds of your harness first.

[@rushjohnston5718]

I just bought a 92’ pickup extended cap deluxe 4wd. I was looking to do this, did the harness come with the needed fuses?

[@6thGearGarage]

Yes it did

[@casualesvideosmunoz7203]

I have my 92 what nomber is a 7x6

[@jackenrod6794]

Did you have to modify the headlight buckets? I had to trim a fair amount to install the thicker LEDs.

[@6thGearGarage]

They were a tighter fit than the old headlights, but I did not have to modify them to fit.

[@heribertomartinez5031]

Hello, could you inform me where I can buy lights like this for my 960 94 tropper truck. Thank you ....

[@6thGearGarage]

Hi, I put the link in the description. Thanks for watching!

[@hectorvelasquez9566]

Saludos amigo. Pon la traducción

[@buenosairesairconditioning1361]

Would you know where could I find that grille with the light vezel silver/black?

[@6thGearGarage]

I don't know if Toyota still makes them. You might try searching on ebay for a nice used one.

[@markgasmen]

Did you get the high beam indicator to light up on the dash when flipping to highs?

[@6thGearGarage]

Yeah I didn’t have any issues with that 👍

[@craigrutledge4339]

Ya I the same issue, lights are awesome but lost high beam indicator on dash?

[@dangerousfandango5943]

I have the exact same ones i just bought this month. Amd they dont fit in the metal housing behind the chrome trim.. i had to cut out the metal housing.. and that caused the adjustments to now be riding alont the new headlights rear housing.. havent turned it on yet due to truck is getting worked on.... So im wondering how yours fit when i have the same light and truck also

[@6thGearGarage]

Mine fit without any cutting, but you're the second person in a week that said they had to trim the metal housing to get these to fit. What year is your truck?

[@dangerousfandango5943]

@@6thGearGarage 1986 pickup 4wd.. they must've gone with a different housing or something.. its just slightly bulkier on each corners.. i tried trimming just a lil. But it wouldnt seat.. had to trim it 180.. so it now doesnt rely on the housing bracket to pivet for adjustments. Its now the actaul headlight thatll pivot around... im just hoping itll still adjust correctly. And hope its as stable

[@PascualAndres]

I got the exact but I need help with DRL

[@6thGearGarage]

These lights don't have a DRL option, but I have another video with LED lights with a DRL option: kzbin.info/www/bejne/bXyUmqKFg6drm5Y

[@alfonsocasillas7290]

With this set up of lights work on my 87 Toyota truck and I have issues with my highbeams they won’t stay on unless I’m pulling on the lever is there a relay or a fuse for highbeams

[@6thGearGarage]

You may need the extra harness that I used.

[@16driver16]

Switch

[@tylerd2853]

im using the same harness but my lights are always on brights and it doesnt show on the dash that they are on. it has no low beams?

[@6thGearGarage]

Someone else had the same problem. I'm not sure why, but it sounds like the harness may need re-pinned at the headlight.