How to make a beautiful front panel for an electronic device

  Рет қаралды 91,450

Anton Pisarev

Anton Pisarev

Күн бұрын

Пікірлер: 41
@UpcycleElectronics
@UpcycleElectronics 5 жыл бұрын
The solvents in that spray can are very similar to acetone or could contain acetone. Although a bit more difficult to obtain a 2 part polyurethane clearcoat will not dissolve the ink/toner. You managed to get the paper off of the ink/toner much better than I can. Nice job. -Jake
@gfr2023
@gfr2023 2 жыл бұрын
wow ready for the market !! great job !!
@KorAllRBare
@KorAllRBare 4 жыл бұрын
Did you know there is a drill attachment that nibbles out shapes? One hole and with a template guide away you go, smooth finish within minutes for plastic, aluminium, and mild steel up to 1.5 mm thick..
@Bremontval
@Bremontval Жыл бұрын
Hi Thank you for the video. One question : is this method working on a Teko aluminium box ? Thank you
@friedmule5403
@friedmule5403 5 жыл бұрын
Maybe I can answer some of your questions:-) 1) What material you try to use as a front does not matter as long it can handle the heat you have to apply. It can be metal, plastic or many other material's. 2) The best paper you can use is paper with a high gloss like magazine paper, laser photo paper and others so long the paper also can withstand high heat so dont use inject photo paper. For best result try to find some paper that also takes water wary well so it get soaked easy. 3) You have to use a laser printer because it melts your motive on top of the paper. 4) How much heat then? You have to apply so much heat that the laser "ink" remelts and sticks to the surface of plastic or metal you want to decorate. Try from 200C / 400F and go up. 5) When you want to remove the paper you just have to soak the paper in water for 5-10 minuts and carefully remove the paper with your hand or a cloth. 7) Last try to search for "making circuit bord" or making PCB" there are a lot of great info you may can use.
@ktrifon
@ktrifon 7 ай бұрын
Wait, a few questions about the first step (or before it). You used a laser printer on what material? Is it proper for this type of job? What is its name? And the most important question, if you want white text and indications on a black chassis / box, what do you do; I have some old synths with white letters and lines worn-out. Thanks
@SianaGearz
@SianaGearz 2 ай бұрын
You must use a laser printer (LED toner transfer printer) since toner is actually a thermoplastic powder that melts onto the surface. You can use glossy magazine paper for the transder, most works. You can also buy special PCB toner transfer paper. Transfer can be done onto most materials. Here it's an ABS enclosure. Polystyrene, polycarbonate, aluminium, stainless steel i believe have all been used with toner transfer. It is possible to buy white toner powder for laser printer (ghost toner). I cannot promise you that it works! You may be able to use drag knife cut PVC foil to restore white lettering and graphics on your equipment. You can get the cuts done at every custom T-shirt shop in the city. Then you apply transfer film, use transfer film to apply the cut design to the item, weed out the lettering and graphics to retain the mask, and paint it in. If you can use alkyd resin paint (model "enamel" paint), it takes a few days to final cure but it's going to be robust and is never coming off, but it can be difficult since it likes coming on thick. If you don't have an airbrush and aren't confident in your thinning and brush craft, spray paint acrylic gives a good outcome in a pinch, but isn't as long term durable. T-shirt shops might give you other ideas as well, they might have multicolour transfer print machines of different kinds. Talk to them.
@Tirdad1981
@Tirdad1981 5 жыл бұрын
Any material can be used. The point is to find the suitable iron temperature for your target material through trial and error. After toner transfer, soak the paper with warm water and wait till it disintegrates easily.
@boogiewoogie2010
@boogiewoogie2010 Жыл бұрын
What's with that suspense thriller music? I had to watch after muting my speakers...
@anassl.9066
@anassl.9066 7 жыл бұрын
Which material the original plate is made of ?
@markov4119
@markov4119 2 жыл бұрын
Nice work! But I was really scared for your fingers when you were drilling. Is there a proper setup to maintain the plastic box while drilling?
@mcnod32
@mcnod32 Жыл бұрын
what kind of plastic is that? Can we use acrylic?
@theaveragejoestinkeringand4407
@theaveragejoestinkeringand4407 4 жыл бұрын
So how can you relabel the front of an old vintage halicrafters communications receiver that has a metal case With what I’m assuming is painted on small lettering. The radio I’m working on needs to be repainted but naturally I will lose all the lettering when I sand and prep the face plate.
@samuelbudiyanto2250
@samuelbudiyanto2250 4 жыл бұрын
Yea, all my project using PVC is beautiful now. Thanks for this video. 👍👍👍👍
@arcorob
@arcorob 2 жыл бұрын
WAIT ! You printed on magazine paper, ironed the backside (for heat) and then you were able to leave the laser print behind by washing the paper with warm water ? Really ? No special decal paper ? Wow
@asdffewfew
@asdffewfew 2 жыл бұрын
special paper is not always available. and a glossy magazine nearby)
@goodwill7643
@goodwill7643 7 жыл бұрын
which temperature do you use to tranfer tonner?
@drawingexpression
@drawingexpression 3 жыл бұрын
Anyone noticed that he has injured on finger during this work.
@srlikes3306
@srlikes3306 4 жыл бұрын
Printing. Ink. Name. What
@DirtNerds
@DirtNerds 5 жыл бұрын
with or without steam?
@Whispering_souls_by_aperture
@Whispering_souls_by_aperture 6 жыл бұрын
Hi i am your subscriber Plz make a video on how to make playstation 2 remote to USB or Micro USB adapter at home
@prounboxing5348
@prounboxing5348 6 жыл бұрын
How can I get this plastic sheet
@aboimad5178
@aboimad5178 6 жыл бұрын
printed on plastic ?
@aebfroman
@aebfroman 5 жыл бұрын
"How to make..." doesn't show how to make. Thanks.
@jimtalltheislandbrothers6639
@jimtalltheislandbrothers6639 6 жыл бұрын
Looks like opaque perspex.
@sagarghatti
@sagarghatti 5 жыл бұрын
Use nail polish remover instead of iron on it
@MoxxMix
@MoxxMix 5 жыл бұрын
Nail polish can damage the plastic.
@Cooper_Bond
@Cooper_Bond 7 жыл бұрын
Подложка от самоклейки в помощь
@user-kp4ik6qd6f
@user-kp4ik6qd6f 6 жыл бұрын
what's the song title?
@joshaughnessy6119
@joshaughnessy6119 5 жыл бұрын
Use your words, not music. I don't need to see you tape and drill EACH hole. I get the idea. BTW, this is NOT a simple method.
@robertcartier5088
@robertcartier5088 4 жыл бұрын
Maybe his words are not your words. And even if his words were in English, you might have found a way to complain about his accent... Some people will never really satisfied. ;-]
@imnotbeluga007
@imnotbeluga007 Жыл бұрын
He's from Russia or other Cyrillic alphabet country, you can see it in the newspaper. So either he would speak his native language, or English with an obvious thicc accent.
@craftymulligar
@craftymulligar 7 ай бұрын
Probably a re dubbed or modified text version. Or really bad accent you can't understand. Someone's repackaged version footage.
@sujijirel4371
@sujijirel4371 7 жыл бұрын
which software you use for design ...?? plz help me...!
@johncoops6897
@johncoops6897 7 жыл бұрын
Any software you like. A Word Processor. Paint. Anything
@lubosholicka3291
@lubosholicka3291 6 жыл бұрын
sketchUp
@whiterottenrabbit
@whiterottenrabbit 4 жыл бұрын
It's as if you DIY guys have a competition going on who has the shittiest, most obnoxious music, seriously... **facepalm**
@tmengucor
@tmengucor 4 жыл бұрын
Can I use toilet paper? Dirty toilet paper.
@bubbahogg-buga4613
@bubbahogg-buga4613 5 жыл бұрын
just use transfer paper ffs...and use anvice formdrilling! amateur
How to make professional looking front panels
17:35
NFM
Рет қаралды 69 М.
Making Custom Eurorack Front Panels with a Laser Engraver
14:34
What's in the clown's bag? #clown #angel #bunnypolice
00:19
超人夫妇
Рет қаралды 40 МЛН
This dad wins Halloween! 🎃💀
01:00
Justin Flom
Рет қаралды 40 МЛН
小丑揭穿坏人的阴谋 #小丑 #天使 #shorts
00:35
好人小丑
Рет қаралды 27 МЛН
How Hamas Makes Rockets against Israel | Qassam
8:17
AiTelly
Рет қаралды 3,4 МЛН
GRAPHIC PRINTED OVERLAY WITH EMBOSSED SWITCH
8:17
TAKACHI ELECTRONICS ENCLOSURE CO., LTD.
Рет қаралды 47 М.
How INDUCTOR's work & How to make your own
15:55
Schematix
Рет қаралды 886 М.
Front Panel Express - How It's Made- Custom Panels and Enclosures
2:52
Front Panel Express
Рет қаралды 53 М.
Making front panels for your electronics project
9:07
TheHWcave
Рет қаралды 13 М.
Making a Low-Budget Front Panel for a Synthesizer-Module
9:44
Andreas Remshagen
Рет қаралды 18 М.
Just Connect Your TV and Watch All the World's Channels in Full HD Format
14:45
Creative Passion 88
Рет қаралды 7 МЛН
Panels: Cheap and easy DIY front panels
14:22
Analog Output
Рет қаралды 16 М.
What's in the clown's bag? #clown #angel #bunnypolice
00:19
超人夫妇
Рет қаралды 40 МЛН