Just watched your video, ported my fuel fitting 1/8".I was actually surprised, despite nonbeliever comments on other forms, I won't say it adds horsepower but definitely throttle response.thanks keep the videos coming!
@jeffbell17453 жыл бұрын
From what I have read about this little mod, it's mainly to keep the engine from starving for fuel when the engine is under heavy loads from pulling trailers and such.
@lextime9427 Жыл бұрын
Does this hurt the already bad fuel economy?
@ericroberts891 Жыл бұрын
I know this is an old video but I was wondering is there a reason you wouldn't port the passenger side fitting also?
@tater09094 жыл бұрын
So I understand the passenger side doesn’t need done? Is it already larger?
@richardnielsen35842 жыл бұрын
Did you do the the valve on passenger side ?? I know drivers side supplys passenger side and if you don't do that one you only get better fuel delivery to drivers ??
@mhtractorservice62878 жыл бұрын
You should drill out the other rail fitting too, 1/16 since the driver side rail feeds the passanger side rail
@TruckMaster8 жыл бұрын
That's a great point I will look into that
@mhtractorservice62878 жыл бұрын
Just trying to help, if you do let us know if it makes any difference, I know on a dual fuel pump setup it's a must or it will fall on its face
@emilycornell72466 жыл бұрын
Tyler Mcbay can you do the same thing to a 2002 lb7
@emilycornell72466 жыл бұрын
Is there any other fuel mods I can do to my lb7 besides the mass fuel system
@bnorby213 Жыл бұрын
@@emilycornell7246 yes but each rail is fueled separately
@ricktryon37853 жыл бұрын
Did it help with towing?
@frankrey76763 жыл бұрын
Is this still something you would do today?
@TM-lw8wn5 жыл бұрын
fyi, should always use a vacuum to remove the bulk of cuttings, then air, less chance of getting metal in the eye. having a doctor dig metal out of your eye sucks, been there twice, much more careful these days.
@ryanfunk11805 жыл бұрын
What is the benefit of this and the benefit of the race fuel valve? Is it better to just delete the valve altogether?
@Billfish5 жыл бұрын
you don’t have to unplug the connectors to the compressor, i just installed my ported fitting and did not have to unplug any of the connectors
@barnbuiltdiesel40367 жыл бұрын
Hey just wondering is there 2 sides and does it smoke now or not?
@TruckMaster7 жыл бұрын
+Travis Pollard there is only one side and no it doesn't smoke more, and yes you can mess it up if you don't drill straight on good luck sir
@barnbuiltdiesel40367 жыл бұрын
Truck Master also on the other side do drill the same size hole?
@gradoisx23486 жыл бұрын
@@barnbuiltdiesel4036 you want your truck to smoke? Take the charge air cooler pipe off and start it 😂
@barnbuiltdiesel40366 жыл бұрын
@@gradoisx2348 I got a smoke lope tune now so no need
@gradoisx23486 жыл бұрын
@@barnbuiltdiesel4036 ...i was joking. And why run a smoke tune and risk washing down your cylinder walls that could lead to engine failure? Unless you dont drive the truck with that tune in
@billybobs8413 жыл бұрын
Is it worth doin it
@BassickS777 жыл бұрын
when you did you fuel valve did you use an o ring? I just did the shims and I didn't notice one so I put it in without one and now it drips fuel
@TruckMaster7 жыл бұрын
+Yamaha Rider that's weird, I never noticed that but no I didn't use a oring there's no need to your just opening the hole some
@BassickS777 жыл бұрын
Truck Master no not the fuel fitting. the valve. I know you said you used a race valve?
@TruckMaster7 жыл бұрын
+Yamaha Rider sorry... but yes I used a oring
@BassickS777 жыл бұрын
Truck Master problem solved mine shot out and landed on the drive way found it this morning and put it in now it doesn't leak thanks for the replies to man
@TruckMaster7 жыл бұрын
+Yamaha Rider awesome man
@billyjones416 жыл бұрын
If I didn't this to my 07 LBZ would it hurt it in any way to do this mod if I don't have the race fuel valve installed yet?
@cholder13396 жыл бұрын
billy jones it will through a low fuel temp code Because the fuel doesn’t have time to heat up in the rail . Only in cold weather. No harm too worry about
@kellygriffith58666 жыл бұрын
I’m sure these fitting will now rust. Injectors are gonna love it
@wholegrain27 Жыл бұрын
@@kellygriffith5866 why will they rust?? They still the same material, still in diesel fuel, just a bigger opening.
@marcosifuentes834 жыл бұрын
I'm doing the passenger side right now,no one has a video on this!:( It sucks! Lol
@kaylachapman44693 жыл бұрын
Any noticable results.?
@ericdemoss80033 жыл бұрын
Did you drill out the passenger side to 1/8th?
@chrisao19875 жыл бұрын
From what I understand the reason for this small hole is to quite the motor down 🤷🏻♂️ I’m going to install the PPE just cause I’m not sure how this will hold up. But it does make a big difference. kzbin.info/www/bejne/aXuai6KHp7CVsKM
@WillCtheMechDrummer3 жыл бұрын
I know I'm late to the comments but... This method is just fine. As long as the individual is capable of doing it correctly, the stock fitting drilled out to 1/8" will hold up great!
@tater09093 жыл бұрын
What’s the sensor plug just above that fitting?
@powerblock706 жыл бұрын
I’m just curious of how safe and reliable it is to drill it out versus buying the ppe fitting?
@chungharkey67696 жыл бұрын
What did this do for your fuel economy?
@TruckMaster6 жыл бұрын
+Chung Harkey it did nothing
@chungharkey67696 жыл бұрын
Truck Master would you say it's worth the time and effort?
@kimminau107 жыл бұрын
How did you remove the belt so easily?
@TruckMaster7 жыл бұрын
+FishFor Crappie 1/2 inch on the belt tensioner it really wasn't hard I did put a cheater pipe on the ratchet to give me more leverage
@melvinstewart54905 жыл бұрын
I don't know about y'all but did this to my truck and man the response was unbelievable. Raps up much faster. Has anyone checked their fuel mileage after this mod?
@TruckMaster5 жыл бұрын
That’s great to know! Thanks for sharing
@ryanphilipps10885 жыл бұрын
Can you do a video on the cp3 modification
@diesel_inthemorning_23156 жыл бұрын
You should do a video on air in fuel system and testing fuel system for leaks no one has one
@huntersteven63205 жыл бұрын
Diesel_inthemorning _ yes please
@larryfrash99915 жыл бұрын
why wouldn't it work for lb7
@barnbuiltdiesel40367 жыл бұрын
Also can you over drill them and mess up?
@blakelittleton6277 жыл бұрын
do you know any free mods like this for the lb7
@TruckMaster7 жыл бұрын
+blake littleton find a way to block off your resonator
@blakelittleton6277 жыл бұрын
I've done that is there anyway to get more throttle response
@Berta_Bros6 жыл бұрын
blake littleton you can do this kid to a lb7
@Berta_Bros6 жыл бұрын
blake littleton there’s a fuel rail port just like this but farther back I did it to my lb7 works charms
@wyattwasson71134 жыл бұрын
Joel Price I cant find it
@cholochedd67526 жыл бұрын
Bro who has a good page for the LB7z??
@billybobs8413 жыл бұрын
Did bully dog tear ur truck up
@felixwalter56388 жыл бұрын
So did you do both side or just one side
@TruckMaster8 жыл бұрын
+Felix Walter no but I really should
@jamnremoval8697 жыл бұрын
fleece did a flow test and doing only the driverside proved to better. the picked up about 500psi over doing both sides.
@leitch1006 жыл бұрын
You get more gains in psi from just doing one side as opposed to both?? I'm trying to figure all this out for my LBZ. I was thinking about drilling both mine out instead of buying from PPE because I can drill quicker than they can deliver, and than I found this clip. Much appreciated.
@randysalazar41495 жыл бұрын
So do both side or no
@jamesdupin7375 жыл бұрын
Great video as always
@rexwilson18965 жыл бұрын
Is there anything like this you can do to the lml
@gobigorgohomeproductions4585 жыл бұрын
Can you do This on the lml?
@TruckMaster5 жыл бұрын
I’m not to sure but I wouldn’t mess with that CP4
@jessepettigrew59395 жыл бұрын
Would you do both sides?!
@maxdura20547 жыл бұрын
Great video, it took me no time following this how to!! Do you have a how to for the fuel pressure release valve or at least some insight on how to move the glow plug module out of the way....it's a bear....
@TruckMaster7 жыл бұрын
+Max Dura thanks! I didn't do a video but I plan to soon
@maxdura20547 жыл бұрын
awesome, looking forward to it!
@barnbuiltdiesel40367 жыл бұрын
When you do the passenger side please make a video I got a little in over my head
@TruckMaster7 жыл бұрын
+Travis Pollard no problem I will do a video on it but it won't be for another month
@barnbuiltdiesel40367 жыл бұрын
Can do its tricky with the egr still there
@user-te6rb5to8c4 жыл бұрын
@@TruckMaster did you ever make this video?
@nateirwin89053 жыл бұрын
@ truckmaster did u ever drill out the passenger side?
@michaelsacy58496 жыл бұрын
Why not lb7
@bnorby213 Жыл бұрын
Who said you cant
@XxCODMASTERFTWxX7 жыл бұрын
When are you going to do the other side
@TruckMaster7 жыл бұрын
+XxCODMASTERFTWxX I'm hoping to get to it in a few months