How to make a silver and turquoise inlay ring without a lathe

I will show you step by step how to make a silver and turquoise inlay ring without using a lathe.
Ring Sizer & Measurement:
Finger Ring Sizer (Very accurate sizes) - bit.ly/RingFingerSizer
Herded Steel Mandrel (Very accurate sizes) - bit.ly/GoldRingMandrel
Finger Ring Sizer (Cheaper but not always accurate) - amzn.to/3ETcF0e
Herded Steel Mandrel (Cheaper but not always accurate) - amzn.to/39CXvOz
Digital Caliper - amzn.to/3AM8EZ1
Sawing Tools:
Nano Saw Blades - bit.ly/NANOSawBlades
Cut Lube - bit.ly/PepeLubeLubricant
5in German Style Saw Frame - amzn.to/3uf3v9p
4.25in GreenLion Saw Frame - amzn.to/3EU9YeR
5in Haymaker SawFramebit.ly/HaymakerSawFrame
5in Knew Concepts Saw Frame - amzn.to/2XUwxQf
Wood Only Bench Pin - amzn.to/2Y6k4su
Bench Pin with Anvil - amzn.to/3obXRnE
Bench Anvil Basic Combo Kit - amzn.to/2Y1Fgjw
Rolling Mills
Pepetools - bit.ly/pepetools130
Amazon Pepetools - amzn.to/30SC6eY
Amazon Economy: - amzn.to/37p8ubv
Files:
Cheap File Set - amzn.to/3zIxurI
Very Nice Half Round File - amzn.to/3m4xFIQ
Needle File Set - amzn.to/3ETCoFZ
Hammers & Mallets:
Rawhide Mallet - amzn.to/3kGm6Iv
Chasing Hammer - amzn.to/3m053jV
Hammer & Mallet Set - amzn.to/2XOWuAi
Pliers:
7-Piece Jewelers Pliers Set - amzn.to/3kGX3oA
Smooth Brass Jaw Parallel Pliers - amzn.to/2WeaHWS
Chain Nose Parallel Plier Stainless Steel - amzn.to/3zGR0Vd
Soldering Setup:
Third Hand Base & Tweezer Set - amzn.to/2Wffs2x
Soldering Tripod - amzn.to/3CNu20H
Heavy Gauge Screen For Soldering Tripod - amzn.to/3ANdKEt
Handy Flux Paste - amzn.to/3zNs6Dw
Charcoal Block - amzn.to/3ucFCj3
Honeycomb Ceramic Soldering Board - amzn.to/2WdveL9
Smoke/Fume Absorber - amzn.to/3lVGuom
Electric Slow Cooker Ceramic Pot - amzn.to/3mixOsz
Copper Pickling Curved Tip Tongs - amzn.to/2WfV955
Sparex Granular Dry Pickling Compound (Acid) - amzn.to/2XZCKtW
24 Paint Brush Set - amzn.to/39KavBG
Basic Soldering Starter Kit - amzn.to/3lYGJ21
Tweezers Set - amzn.to/3zJ8Gjc
Titanium Tweezers - amzn.to/2XSdjdj
Torches & Ignitors:
Automatic Torch Igniter - bit.ly/AutomaticTorchIgniter
Cheaper Automatic Torch Lighter - amzn.to/2ZATXKQ
Hand Torch Lighter - amzn.to/3CIXKUs
Butane Torch - amzn.to/3ob8bMw
Propane Torch End With Starter - amzn.to/2XUNt9i
Standard Propane Fuel Cylinder - amzn.to/3obvJRI
Mapp/PRO Gas Torch End With Starter - amzn.to/3CMAJ38
MAPP Gas Cylinders - amzn.to/3CMAJ38
Basic Smith Little Torch All-Fuels System with Five Tips - bit.ly/SmithLittleTorch5tips
Amazon Smith Little Torch - amzn.to/3ET2TeK
Smith Equipment Mag Stand - amzn.to/2Y1LqAa
Full Smith Acetylene Oxygen Setup - amzn.to/2XWBHLA
Solid Titanium Solder Pick (My Favorite Solder Pick) - bit.ly/ErgoLastTitaniumSolder...
Solder:
Bulk Silver Solder in 1oz sheets - bit.ly/SilverSolderSheet1oz
Extra Easy Solder - amzn.to/3zIEyVg
Easy Silver Solder - amzn.to/3COruiZ
Medium Silver Solder - amzn.to/3kGroDR
Hard Silver Solder - amzn.to/3kPxhPj
Extra Hard Silver Solder - amzn.to/3CRzYWn
Easy, Med & Hard Solder Set - amzn.to/2XWCmg2
Sand Paper & Rotary bits:
Wet Dry Waterproof Sand Paper 120 to 5000 Grit - amzn.to/3lYKbK1
Rotary Bristle Disc Kit 80 120 220 400 600 1000 Grit - amzn.to/3kGsEH5
Silicone Rubber Polishing Wheels - amzn.to/2ZtvyGR
Polishing Discs & Compound:
Yellow Polishing Buffing Wheel Buffs - amzn.to/3AJoX92
Fabulustre Polishing Compound - amzn.to/3ufdM5t
Silicone Finger Protectors - amzn.to/3EVihXV
Wool Felt Polishing Wheel - amzn.to/3ET5yFg
Polishing Machine - bit.ly/SingleSpindlePolishing...
If you are looking for some quality CA glue check out the stuff made by StarBond. Use code "GomeowCrations15" at checkout to save 15% on your order and free shipping. bit.ly/StarBond
________________________________________________
If you are looking for more tools and materials that I use, well you're in luck! I made a page on my website just for that and I'm updating all the time so bookmark it to stay up to date:
GomeowCreations.com/tools-and...
GomeowCreations.com/partners-...
________________________________________________
My PATREON ➜ / gomeowcreations
One time support ➜ paypal.me/gomeowcreations
________________________________________________
Instagram ➜ / gomeowcreations
Facebook ➜ / gomeowcreations
________________________________________________
#jewellerymaking #jewelrymaking #silversmithing #gomeowcreations #ringmaking #inlayring

[@octane_rl4659]

Perfect video! im making 4 of these for my brothers and I, with our birthstones and a small pinch of my fathers ashes that just passed away. Thank you for this.

[@MSYNGWIE12]

What a "touching" gesture. A very special way to keep a loved one close, a future family heirloom.

[@gavincarroll2553]

Bro that's bad ass

[@everywherelies]

😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊

[@user-kx9bx7pz1q]

​@@MSYNGWIE12😊😊😊😊😊😊😊😊

[@user-kx9bx7pz1q]

​😊😊😊😊

[@tonyha3827]

This video is the best. No frills, concise to point, yet so through to instruct.

[@GomeowCreations]

Thanks and yeah I do try to make my videos like that 😁👍

[@Aikidobear129]

Beautiful job- I love it when a person shows you what can happen in real life- like mislaying their tools or running out of things - in your case the hardener. It makes me feel like I'm not alone when it happens to me. Handmade pieces of art are far more precious to me than something coming off of lathe- as you put your heart and soul into each piece and a bit of it stays in the work long after you're gone.

[@AjithKumar-on4wu]

உங்கள் சொந்த டி எஸ்கேப் போன்ற விளையாட்டுகள் மற்றும் அரங்க டூ ஆன்லைன் நிறம் விளையாட்டு போன்ற விளையாட்டுகள் மற்றும் நிதி ஆட்டோ காட் கோட்டை ஆகும் என்று z

[@BerkelBoy]

​@@AjithKumar-on4wuwtf are you on about?

[@dangbert11]

Back in the early 70's I was assigned to Taipei AS in Taiwan. While there I got interested in lapidary and silver work. I always wished I brought the torch we used back with me. Unlike the torch in this video, it gave a very gentle, but hot, flame. It was a canister with a foot bellows and a light weight torch that gave a very soft flame. The system used Naphtha as fuel. All tubing was just run of the mill plastic tubing like you would use on a fish tank. You never had to worry about moving the solder with the flame or burning the piece. Cheap and worked like a charm. Do wish I had brought it back.

[@mjremy2605]

So interesting! Many technical details like accurate measuring, not stretching out the thinner wire strips, using Easy Solder which has a lower melting point than the first solder, multiple quenching to preserve metal crystal structure, multiple pickling to remove firescale for better solder adhesion, wow! This is what master craftsmanship is all about. Very grateful for your knowledge sharing and I admire your expertise with jewelry making. It looks like alchemy to me. I love jewelry so much. Miniature pieces of art and bringing together so many skills in the jeweler - knowledge of how various metals will behave with fire, hammer, chemicals, stone knowledge, tool knowledge, understanding of hazards with fire and chemicals, and more. What a fascinating universe of learning. That is one beautiful ring!!

[@CoreySchmick444]

You're the man! I love when people show the old skool way to do things and how you start out. I think everyone should have to do things first without machines and lathes to appreciate them when they do come into their life!

[@GomeowCreations]

Thanks and yeah I wanted people to know they they don't need all the crazy tools that I have to make stuff like this but it does make it a lot faster and easier if you do 😅

[@tcrosley945]

Km

[@WolfgangHartmann-ez1cg]

Or if we can’t spend the money.

[@annewanyoike2041]

​@@tcrosley9455

[@Greyswyndir]

Beautiful little job. This is the first time I've watched someone make a ring. When I was a younger man I had the opportunity to work with a Navajo silver smith and master craftsman. I wish I would have taken him up on his offer to become his apprentice, but I was young and dumb and more interested in exploring the country at the time. Now that I'm older and slightly wiser, I wish I would have taken him up on his offer. The Navajo man's work was amazing, and if I had apprenticed under him, I'd probably be an expert by now.

[@sabrinaduckett5057]

What a fascinating process! This process is not what I was expecting for the turquoise stone, but gosh is it cool!

[@dejonesmanagement]

I like this video for a couple of reasons. Having sat at a bench for a time, it's not talked enough about running out of stuff or improvising because you can't find something else. That's an every day occurrence. Great job on the ring... great video!

[@GomeowCreations]

Well thank you very much 😊

[@mohdalam9020]

Alam8865837273

[@dejonesmanagement]

@@mohdalam9020 Good morning Sir. You'll have to forgive me but I have no idea what that means. Lol!

[@GomeowCreations]

It's likely spam

[@dejonesmanagement]

@@GomeowCreations okay gotcha. I just watched the vid on your Benchmate. Way awesome setup. Makes me want to give up accounting and go back to the bench.

[@clackersclarke4450]

I have been watching many ring videos of late, and they all make we want a lathe that I can`t afford. This was very helpful for me with limited tools. Thanks.

[@GomeowCreations]

Thanks and this is what I made this video 😁👍

[@TheUnholyPosole]

I'll buy you one, are you on Instagram?

[@GomeowCreations]

Yep just search GomeowCreations on IG

[@oscarlavista7677]

Really? 300 for a hobby lathe is too much.

[@GomeowCreations]

Yeah for some people it is too much especially when we're starting out. That is what I made this to help show that you can do it by hand and work up to getting the better tools.

[@jerrywaters4814]

That was quite the watch! I think showing that you don't have to have no equipment to make jewelry is the way to influence beginners that they can make it as well.

[@ArkRed1]

I love the idea of not needing a lathe. It's more time consuming, true, but worth the extra effort and saves you buying a thousand dollar lathe. Thanks for posting.

[@GomeowCreations]

You can get a cheap lathe for $500-$600 that will work for this. I got one used for $400 but I wanted to make sure people know how to do this without one. 😁👍

[@nachtbild]

Thank you very much for showing and explaining the process without the expensive tools only jewellery makers have. Your ring is gorgeous! 😍

[@GomeowCreations]

😁

[@earthresident1007]

I’m not a jewelry maker and will likely never make this gorgeous ring, but your video was really great. I enjoyed watching this and wish you continued inspiration. Beautiful job!

[@GomeowCreations]

Well that is actually really nice to hear, thank you and thank you for taking the time to watch it and leave a comment 😁👍

[@putusudarmayasa7775]

@@GomeowCreations y

[@0Heeroyuy01]

@@putusudarmayasa7775 wynaut

[@andrewarnold3982]

Tip You can use a drill with a large bit wrapped in masking tape as a lathe, it only really works well for polishing and final shaping but I never needed it for anymore. It just makes life 1000 times easier lol

[@derekirelandsirsmokepotalo1152]

I don't know why 556 people would dislike this video he done fantastic work explained every step in detail what else do people want from him if it's not for you why even watch the video anyways thanks for the great video you inspire people to get away from the computer and do sum thing with there life's

[@Vulcano7965]

So I already made a bunch of wood rings with various stone inlays, but your video showed me that I should use the metal-powder-infilling a lot more frequent. Looks really great!

[@smiles.69]

Thanks for the hints! I've made a couple of rings with stone inlays from the Washington area: some Black jade and some listwanite. Didn't use the piecemeal method, instead used inner band as a template for a slab of stone, cut the slab in half, ground out a semicircle in each half - while checking for fit, then assembled the outer rings on the inner band, filled in blemishes with extra easy solder, epoxied the halves onto the assembled ring, then used the lapidary trim saw to cut away the ring from the stone. Finished the final dimensions of the stone and polished all on a Diamond Pacific Genie cabbing machine. Thanks again for the video, I found it very easy to follow!

[@rhondapainter9719]

Excellent !! Thank you for this. Most interesting to watch even very late at night. Don’t know if I’m ready for this yet but someday soon.

[@PHARRAOH]

I always wondered how they got the what looked like solid stone to form. cool video. thanks

[@GomeowCreations]

😁

[@michigansucks23]

Thank you for sharing this. I can't wait to try it myself!

[@Morn2moon]

Wow watching this (that I just happen upon somehow) has made my appreciation for my jewelry pieces go up 110%. I didn't realize how much work went into them. I am profoundly impressed. Thanks for posting.

[@GomeowCreations]

Well thank you very much 😊

[@edwardafftor4205]

Stylish ring. Detailed manufacturing process. Thank you so much for the tutorial.. I wish you health and prosperity

[@allaroundgamer1903]

I always liked to turn on the Science Channel and this is just like watching those "How It's Made" episodes. Great work man!

[@GomeowCreations]

Thanks and yeah I also liked watching how it's made when I was younger 😁👍

[@JTCoinRings]

Absolutely beautiful!

[@sfbfriend]

A little tip that you could use if you wish is when sanding your edges like you did here, make figure eights and rotate piece 1/4 turn frequently while making these figure eights. This was how I would lap seal faces that were used in hydraulic pumps. Creates a flat surface.

[@tm13tube]

I’ve wanted to learn this for ages but, alas, I’m in my 70’s and already weave, knit, and leather bind and restore books.

[@chuckvoss9344]

that ring is something to be proud of. good job.

[@kwdoug]

Absolutely fantastic. Thanks for making this and hardly wait to see your others

[@GomeowCreations]

Well than you for taking the time to watch it 😁

[@lubabe9969]

Beautiful ring my man, well done.

[@GomeowCreations]

Thank you 😁

[@FourJaysFour]

Nice work!! The quality of audio & your editing style make these videos so enjoyable to watch!!

[@erinwahl1738]

I typically make everything by hand.. this was an excellent tutorial regarding inlay! Thank you!

[@k192447]

magnifico,parabéns.

[@KaitlynOxfordTV]

This is such a cool way to use up scrap metal and scrap stones!

[@GomeowCreations]

Yeah it really is 😁

[@pharmycat10]

Absolutely gorgeous and fabulous video, thank you!

[@wendysouthern5770]

hi I am just starting making my own ring for my partner for our 15th wedding anniversary, this was a fabulous insight on how to make a beautiful ring thank you.

[@TheseusTitan]

When we made rings like this we never bothered with a calculator for sizing. We used string and then added some extra length that we cut off once we curbed and cut it. We also soldered the two wires onto the flat piece while it was flat. We curved it, cut it and then solder the whole thing altogether at one time.

[@georgealderson4424]

Remarkable sir. Thank you. It speaks volumes for the quality of the work (and the patience of the maker!) when you take the time to explain in such detail every little part of what to do, how to do it, possible pitfalls and how to overcome them! Thank you (again!) Blessings and peace from UK.

[@GomeowCreations]

Thank you 😊

[@Raksasa187]

i had no idea how to make such a ring, but now i must try it myself!!

[@tammiehonican76]

Your instructions are so good you make me think that i can do this! Beautiful ring! Thank you for this video!

[@pacoblancosmith]

Great job in describing all the steps! That’s how instructional videos are meant to be. I’ve got nearly half an oz of 24K gold dust and now I know what to use it on!

[@GomeowCreations]

Thanks, I never know if I'm going to get my point a crossed so it's good the hear this. 😄 As for your gold dust, I would melt that down and make some wire or sheet of of it before using it to fill in cracks haha

[@pacoblancosmith]

GomeowCreations I have other gold scrap to do that with...all from my recycling old computers and electronics hobby

[@airinbakery6440]

It was awesome .I am a Goldsmith student and I'm happy to find you. Thank you

[@GomeowCreations]

Well thank you and that's awesome you are becoming a goldsmith. I really need to start working with gold haha

[@airinbakery6440]

GomeowCreations, for now, we are working with silver. I prefer silver than gold too 😉

[@SandippHalder]

This is very good thing that you direct the hole process very thoroughly with the video.. very nice.. keep it up.. .

[@jameslucas5590]

I woke up early this morning before work and went to KZbin. This video was a relaxing start to my day. Although I am a programmer by trade, I might take this up as a hobby. I will have to find some workshops. Thank you.

[@GomeowCreations]

Well good morning 👍 I have some other videos that show some more of the basic techniques needed to make jewelry. You might find them helpful

[@jameslucas5590]

@@GomeowCreations I will be taking a look at them. I have a son who is 16 and is interested in creating rings. So this will be an enjoyable adventure for both of us. Thank you for your response.

[@BeenJamin66]

This is a great video man! Recently, I’ve been making rings out of coins, and it sure is a different process, but this video is very helpful in providing me with new insights into ring making. Also, I really like that Dremel.

[@MsDreamcakes]

This is an awesome video, very informative and I love that you are showing a different way to go about making a ring. I think we tend to get hung up thinking the way we know is the only “right” way but I appreciate that there can be many ways to get a beautiful end product like the ring you created here! 👍🏼👍🏼👍🏼

[@GomeowCreations]

Well thank you very much for your kind words. I want people to see that you don't need thousands of dollars in tools to make something like this 😁👍

[@MsDreamcakes]

GomeowCreations I think that’s great! I’m a self taught caker who only got into it because of a life changing illness. Along the way I’ve learned to do amazing things with ordinary stuff I find around my house! I got (and still get) folks telling me how I’m not doing things “right”......lol 🙄 I choose to surround myself with people like you who can see great possibilities in regular ole stuff! 😁

[@rickymcintosh3911]

Really beautiful job when I retire I was thinking about doing some woodworking but it really makes me think about doing jewelry

[@GTFBITK]

I love turquoise and silver. Thank you for the video.

[@lauriebennett6257]

Beautiful! I made a similar ring in Art class when I was in high school. We oxidized the area where the stones went so that there was the contrasting color.

[@GomeowCreations]

That is a good idea, you can also paint the inner area of the ring so you have different color options.

[@PUBGMOBILE-pj6lk]

@@GomeowCreations و7تتخنسررسسششبيسءتعتتتتنتنتتىللاتت90نهعغعععنتتتتتتتتتتتتتوزتننزوزززتننننههنننتتتايثيسئ0حمننتنن طىعااااا ههههنتتت تتتتتااآتح0منننننتننن اتتتتنتتتتتتعتتتتنتتتتتتتتتتتتتتنخععتتتتتتتتتتت0 ووزوووووو و ززززو و ووووووووووو هتاااااء0000000000 ة اا 😬😈😈😈😇😇😆😆😆😆☺☺☺😆😤😣😤😇😇😠😠😠😠😠😠😠😇😠😠😠😇😇😇😇😠😠😠😠😠😠😠😠😠😠😬😬😬😬😬😬😠😠😠😠😠😠😠😠😠😠😠😠😬😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😆😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠😠مززززنزظممممكممخخم😬😠😠😠😠😇😇😇😇😆😆😇😇😠😠😠😠😠😠

[@kathybradley7463]

Watching a beautiful ring like that being made was so cool. Thanks for sharing.

[@GomeowCreations]

Thank you very much for watching 😀

[@Richy7010]

Thank you for this good explained tutorial.

[@splash7489]

Thank you for sharing, I really appretiate your hard work and kindness

[@namorrison1979]

I took a high school jewelry class and this is how we made our inlay rings

[@GomeowCreations]

Oh really? Well that's cool haha. I'm happy to hear that I came up with a way to do this that is all ready used in schools haha.

[@namorrison1979]

@@GomeowCreations this was back in 1998 I lost the ring but loved the video because it shows what you can do without having a lot of equipment

[@gaylahasbel2506]

Thank you for sharing your incredible talent with us. I can't wait to make matching rings for my upcoming wedding. 💜

[@GomeowCreations]

Thank you and best of luck, let me know if you have any questions. 😁👍

[@youngfresh9780]

Thanks that was really cool I’m new to making jewelry but I loved how you broke everything down great job

[@wendytitterton5004]

Thank you for this wonderful informative tutorial. Very clear step by step lesson.

[@kimlyons8550]

Thank you so much for this. I had no idea how inlay was done. I also didn't realize I should be using wet sandpaper.

[@GomeowCreations]

No problem and thank you for watching 😊. There are other ways to do inlays just this is one of the easiest in my opinion. Also only use water on sand paper that says it can handle water other wise it will just rip.

[@prettyhandson1572]

Thank you so much for sharing this. I would love to buy something like this for my man. I appreciate how you broke down every step and said what products you were using and how long it took etc. Thank you!

[@GomeowCreations]

Well no problem and if you would like something made please feel free to contact me 😊👍 [e-mail]

[@user-ll5os5gl2t]

kzbin.info/www/bejne/iqmQfHuVnbd0o9U

[@bandilla7317]

ILove this idea very awesome thanks for sharing this video

[@tmonful]

Great video. Explained great for someone like me that knows zero on making ring with inlay.

[@merlinfalcon8518]

Masterclass. You made that look so simple!!

[@GomeowCreations]

Well thank you 😊

[@tabasdezh]

The green turquoise and brass powder are one the best combinations of colors .

[@GomeowCreations]

😁

[@tabasdezh]

@@GomeowCreations the turquoise in the beginning of the video was green but at the end of the video turned into blue :))

[@GomeowCreations]

It might have been a light problem 😅

[@evelynlobos1354]

amazing...wow....I did a silversmithing Course years ago then did an arts degree and majored in silversmithing and loved it ...but had no work upon completion and ended up doing a graphic design course and that got me into working in that industry and I always drew at home and often wanted to do some silversmithing but now as covid has changed many of us and our careers I find that I want to set up a work area at my family home, my dad has many machines as he was a welder and so there is a lot of stuff I can use or make use of. Your video has inspired me to get back into it and will certainly be using the this as one of my attempts to get my rings done ..I love working with silver was not a fan of gold,

[@elainecameron7787]

That ring is amazing

[@louiechidwick6034]

Beautiful work! I don't have a lathe, but what works just as well for rings, is to adapt a tapered mandrill to fit the chuck of a drill-press and you have an instant vertical lathe!

[@GomeowCreations]

Thank you and yes you can use a mandrill with a drill or drill press but a lot of people done have that either.

[@arshadnaeemkhan7430]

What a beautiful piece. Marvelous.

[@GomeowCreations]

Thank you very much 😁

[@TheDirtySkirtz]

$100 says nobody can reply with one they made! Within 24 hours 💜 💯

[@GomeowCreations]

Does this apply to me as well? If so I'll be taking that $100 😁👍

[@johnnyc.5979]

Excellent instructions. I will make one as soon as I have all the tools and supplies.

[@GomeowCreations]

Thank you and I'm working on a better tool and material list right now that you might find helpful 👍

[@kimbain4368]

What a beautiful end product! So interesting to watch the technique. KZbin recommended you and I'm now a subscriber. TFS!

[@GomeowCreations]

Welcome to the channel and I'm happy to have you 😄👍 and thank you very much for your kind words about my work.

[@cimkep8250]

I'm glad I got this in my recommended list^^ Nice work

[@GomeowCreations]

Well I'm happy to hair that I'm popping up in recommendations and thank you 😁👍

[@SigiCoria-cd9vg]

Ur voice is so calming im falling asleep boss 🎉

[@jeffreyniles6575]

It was pretty easy to follow along with you. Thank you for the lesson.

[@joyjohnson5355]

Thank you for the awesome video! Great tip on sawing between the silver ends before you solder them closed - mine are usually crooked after filing. So excited for your other tutorials! :)

[@GomeowCreations]

There is another tool that does this even better. You can see me using it in my newer videos. 😁👍

[@nathalieschumann8499]

The ring looks amazing! I‘m in way over my head with the techniques you use (starting with the formula for the correct amount of silver right at the beginning, I was like „What? Hang on...“) but this makes me want to take a jeweler‘s course more than ever!

[@GomeowCreations]

Thank you and if you want I can explain the math better for the ring if you want me to. 😁👍

[@nathalieschumann8499]

GomeowCreations I would love that!

[@Chef-Really5365]

You've given me the education vid to create a unique Art Form .Ive many stones and wondered how to use them. Mosaic Tile Art with this Method .👏🏻🙏🏻💖🌟😎

[@sweatyskunks2378]

Awesome video your a champion for making this 👏

[@bonnierusie9631]

I wish there was a "love" button! It is beautiful! I love jewelry! ❤💖💝💟

[@GomeowCreations]

Well thank you 😊

[@chaztech9824]

you should make a wet table with a mandrel in it and put changeable flex wheels, I made one cheap! great stuff m8 keep it up!

[@0Heeroyuy01]

wish i was skilled to do stuff like this, id love to make one using jade and emeralds for the center section

[@iwondery1725]

I'm really enjoying your videos and learning from them. I appreciate seeing your list of tools and supplies, too. Thanks also for adding that you're using something because you can't find what you actually needed, as you do in this video. It makes me feel that I'm not such a twit when it happens to me. :D

[@Nickscreativestuff]

Thanks for demystifying how to make such a gorgeous looking ring ... you make it look so simple I’ll have to have a go ... keep up the good work.... All the best to you.

[@GomeowCreations]

😁👍

[@sonializondo4992]

Hermosa creación me gustaría saber que líquido pones

[@jojomart]

The ring is stunning! You're so talented!

[@GomeowCreations]

Thank you so much!

[@pamelawerdmullervonelgg1888]

Great video❤ thanks for your clear and professional directions👍

[@dadk5470]

Another beautiful masterpiece. You are the only channel I sit trough the advertisement without skipping. I hope one day to be able to contribute to your channel financially. You deserve a lot.

[@GomeowCreations]

Well thank you very much. 😊

[@anonymous-zk3mi]

One Ring to rule them all, One Ring to find them, One Ring to bring them all, and in the darkness bind them. My precious...

[@GomeowCreations]

😊

[@PATentPending310]

Really cool project, ring looks great!!!

[@user-ll5os5gl2t]

kzbin.info/www/bejne/iqmQfHuVnbd0o9U

[@dalyospino978]

Que precio tienen cada uno de esos anillos y cual es la dirección para comprarlos

[@rezayousefi9763]

6220

[@HOANGLEUSA]

beautiful ring , thanks for sharing , have a nice day

[@AJB2K3]

Wow, thanks for this video. The ring looks amazing.

[@GomeowCreations]

Thank you very much 😊

[@oepolish]

I'm really good at soldering, so I think I'm gonna try this

[@GomeowCreations]

Well give it a try and let me know how it turns out 😁👍

[@henriherrera9744]

I was thinking the exact same thing. It's kind of related after all. Need to learn the safety measurements for this craft tho.

[@clarefabula4588]

Good with a soldering iron or with a torch?

[@clarefabula4588]

It's a totally different technique

[@davidhuber9418]

I loved watching you make this ring, great job it looks awesome, and I love how you use your channel to not show off your face or tattoos

[@GomeowCreations]

Thanks 😊 and what, people do that?

[@lovelyan896]

But I wanna see him😊

[@GomeowCreations]

@@lovelyan896 haha

[@Cochranflutes]

Very nice, I love the color combo!

[@robertoescobar007]

Man you got the patience, you got the Art! 👏👏👏👍❤ great video love it!

[@antsquirly7654]

I was taught to use clear epoxy, works great. One time I used JB Weld and the contrast was even better. that was 40 years ago and it still looks good. Of course I had my wheels & buffers for the finish work, too. - Can't see super glue lasting that long.

[@GomeowCreations]

I have some resin now that I will be using in future videos. I have seen that the super glue does hold up pretty well but time will tell 😁

[@fgeste4409]

Monkey glue Well .. gorilla but pfft..

[@antsquirly7654]

@@notfiveo Interesting, I never had that problem.

[@AdrianoPedrasPreciosas]

Que maravilha 👍🇧🇷

[@GomeowCreations]

Thank you 👍

[@Abyss477]

@@GomeowCreations at the beginning did you do the calculations to get the length of the metal sheet you needed To make the ring?

[@douglaspohl1827]

@@Abyss477 aàaaàààáß

[@jazzys8240]

Beautiful. I use to make Silver jewelry. I would like to start again.

[@Adehsn]

i have always wanted to do this with crushed amethyst.. thank u!!!

[@cezar909090]

Nice to see that the iPhone is useful for something. The ring is.. Awesome. :) Like

[@lisajarvis3820]

OMG~ HAD TO WATCH THIS A FEW TIMES JUST BECAUSE I WAS MESMERISED BY THE PROCESS ~ I ALWAYS WONDERED HOW THIS WAS DONE ~ NOW I KNOW ~ FANTASTIC JOB TOO ~DID NOT REALISE HOW MUCH EASIER THIS WAS TO DO THEN WHAT I HAD IMAGINED ~ AND THE TOOLS TO MAKE IT ARE NOT AS COSTLY EITHER! THANK YOU SO MUCH ~ I WILL BE A NEW SUBSCRIBER AS WELL A NEW FOLLOWER!! 👌🏾👍🏽😎

[@GomeowCreations]

Hey, thanks and I make that video to show people that you can do it without all the high priced tools. The down side is that this takes a long time and a lot of filing. 😅

[@cbusheden]

This is how I was taught at Medway Art College 30 years ago. Just picking it back up now, wish I hadn’t waited so long 🤨

[@Greyswyndir]

He made it look easy, it's probably a little more difficult to do then you think.

[@kresimirmilisa5560]

very nice production of the ring.

[@joelbitton]

Thank you, great video, very empowering.