Be sure to offset the bottom rail left or right a little to allow your rods to lean into the top rail. This will help to keep rods from sliding out of the top rail.
@thomashelmut184811 ай бұрын
Nice Video, nevertheless I would prefer, to do the bottom rack in a easier way: use two boards, in the upper one drill the same holes as done in the top rack and glue/screw a solid board below.
@Geoonthegrind3 ай бұрын
Sir, you did a great build and the video was straightforward and easy to keep up with.
@randygreen6652Ай бұрын
Your priorities are absolutely 💯
@hammer98562 жыл бұрын
A Forstner bit or clock makers bit would also do a great job on the base... (the bits are expensive, but cheaper than a router).
@garrettbrowne274 Жыл бұрын
Best DIY video I’ve seen so far on a wall mount rod rack! Just finished my fishing/work bench now it’s time to make a rod rack that will save me much more room!
@BassBrothersFishingDMV Жыл бұрын
👍🏾👊🏾
@jamiethielen3 ай бұрын
My son and I are making this for my husband for Father’s Day following your instructions- it’s really easy thanks!
@BassBrothersFishingDMV3 ай бұрын
Awesome gift
@garry1214Ай бұрын
Very nice build, I will use some of your ideas in my build for my son in law. Thanks
@duanetaylor15262 жыл бұрын
Great DIY video. The Rod Rack looks great on the wall. I will be doing something similar for sure in the near future. Thanks BBFDMV for another great one. Tight Lines!!!
@BassBrothersFishingDMV2 жыл бұрын
Thanks Duane. This was way overdub than for me.
@hammer98562 жыл бұрын
If you are limited on ceiling height to fit the rods, one could build 2 of the top pieces and mount the rack horizontally on the wall. Love your DYI projects.... Keep'em coming.
@BassBrothersFishingDMV2 жыл бұрын
Yea I might do that if I end up buying more 8 footers
@joeschmoe13014 ай бұрын
Looks beautiful!!
@greggdsciotto8952 Жыл бұрын
Well done sir!
@dacountryone2 жыл бұрын
Hey bro I just started watching your videos,and I have to say they have gave me a lot of valuable information,thank you...keep up the great work. I just go finished with my jon boat build,wish I could show you my VERY first build,I am proud of my self and my son.
@BassBrothersFishingDMV2 жыл бұрын
Sounds awesome man. Would love to see it. Message me some pics on FB messenger or Instagram at Bass Brothers Fishing. The links are in the description of this video.
@5wisher5weet Жыл бұрын
This is great, thanks for theinspiration
@phils67332 жыл бұрын
Looks nice and clean, good job. Just decluttered my garage for my boat and this is a definite must make.
@BassBrothersFishingDMV2 жыл бұрын
Thanks. This was a long overdue project for me. And besides, decluttered brain catches more fish. 🤣🐟🎣
@robertchadwick15528 ай бұрын
That looks great. Thanks for showing us how you did that.
@BassBrothersFishingDMV8 ай бұрын
Cool 😎
@dadoutside Жыл бұрын
Nice!!! Thanks for the video!!!
@johnsanders714 Жыл бұрын
Looks great.
@deanmuddiman47566 ай бұрын
This is excellent, very pleased with the outcome
@dougmerritt67484 ай бұрын
Nice video. Well done and easy to follow along.
@reenoV Жыл бұрын
Wow! Awesome job! I'll look at other how-to videos, but I'm quite positive I'm going to go with this plan.
@BassBrothersFishingDMV Жыл бұрын
Awesome. Be sure to offset the bottom rail left or right a little to allow your rods to lean into the top rail. This will help to keep rods from sliding out of the top rail.
@francoisl7663 Жыл бұрын
Material prices are crazy nowadays, so many projects you're better off buying online but I think this is much more robust for the price than an online option. Will be making one. Thanks!
@BassBrothersFishingDMV Жыл бұрын
Prices are actually going back down thank God. Check home depot and Lowes out. At least they are around here. Good luck.
@johnnyross3340 Жыл бұрын
Great idea , well explained , so just going to have to pinch this ....off to the store for materials. ... THANKS.
@macsmith2092 Жыл бұрын
That looks great! Thanks for sharing.
@JoeKen5399 Жыл бұрын
Can’t wait to build this
@BassBrothersFishingDMV Жыл бұрын
It's rock solid. Note: install the bottom shelve with a slight offset to the tip so your rids lean into the slots.
@zman8340 Жыл бұрын
Great vid will be using this as a guide to make mine soon . Thank you
@fishingwithvance2 жыл бұрын
I love this idea. I may build one of these. Great job. I build your motor stand too. (very close anyway...) Fish on!
@BassBrothersFishingDMV2 жыл бұрын
Awesome man.
@SluSharkND2 жыл бұрын
Love your projects, Sir. Keep up the great work!
@BassBrothersFishingDMV2 жыл бұрын
Thanks.
@Mizzle63222 жыл бұрын
Another great build
@BassBrothersFishingDMV2 жыл бұрын
Thanks
@Mizzle63222 жыл бұрын
Currently working on a boat project with my son not a jon boat but 16 footer I got all the info from you keep up the good work and I'll send you picks when I'm done
@BassBrothersFishingDMV2 жыл бұрын
@@Mizzle6322 yea man looking forward to it.
@jimbobakabrutus1230 Жыл бұрын
Nicely done. Great video too.
@BassBrothersFishingDMV Жыл бұрын
Thanks
@brucewaldron78539 ай бұрын
Drill the end 2 bases right thru the timber and your 8’ rods will fit
@redhusker58 Жыл бұрын
Very nicely done sir!!
@BassBrothersFishingDMV Жыл бұрын
Tx 👍🏾
@NorthWoodsWes2 жыл бұрын
I'm a simple guy. I see rod rack and I click like!
@55beeman Жыл бұрын
Great job 😊
@BassBrothersFishingDMV Жыл бұрын
Thanks
@michaelpearson5965 Жыл бұрын
Don’t forget to use the space above your head for fishing poles also the space above the garage door.
@southbreeze67452 жыл бұрын
Very cool!
@BassBrothersFishingDMV2 жыл бұрын
Thanks
@ChrisWiles-nu4sk Жыл бұрын
and the action is perfect. put a small spinning reel on it with ...
@georgegainey2687 Жыл бұрын
Nice job
@BassBrothersFishingDMV Жыл бұрын
Thanks
@michaelferik80609 ай бұрын
You might have enough room to sneak in the 8' rod horizontally back behind the vertical standing rods on the top rod support. 😎
@BassBrothersFishingDMV9 ай бұрын
That's exactly what I did lol
@fernandosalgado68539 ай бұрын
Muy bueno !!!
@BassBrothersFishingDMV9 ай бұрын
Thanks.
@S1avk02 жыл бұрын
Nice vid! Guess no Tridelph this year... Maybe ill see you on RG. Tight lines!
@BassBrothersFishingDMV2 жыл бұрын
I'm still hoping it will open up at some point.
@S1avk02 жыл бұрын
@@BassBrothersFishingDMV me too, was starting to figure some parts of it out 🤣
@mmanut Жыл бұрын
NICE JOB, VERY PRACTICAL. PS, NEW SUBSCRIBER ‼️ Vinny 🇺🇸
@BassBrothersFishingDMV Жыл бұрын
Thanks. Welcome to the channel. 👍🏾 👊🏾🤙🏾
@markfrye98852 жыл бұрын
what kind of table are you using in this video?
@peca25911 ай бұрын
I also have 16 active rods😂
@JJDaBossOutdoors7 ай бұрын
How long is your board?
@dreams1599 Жыл бұрын
So I'm counting a materials list of 4 1x4, screws and wood glue. Did I miss anything?? Your video seems pretty simple to follow, but any chance you have plans for this project?
@BassBrothersFishingDMV Жыл бұрын
I put items in the video description. I do not have a written plan for it but I made the video step by step so it should be pretty easy to follow.
@dreams1599 Жыл бұрын
@@BassBrothersFishingDMV thanks
@brenettalewis4414 Жыл бұрын
Who is the manufacturer of your workbench?
@BassBrothersFishingDMV Жыл бұрын
I bought this from Amazon. The bench is sold by Keter. Here is our affiliate link in case you buy it from Amazon. Using this link helps to support the channel's growth. Thanks for reaching out and watching our video. Stay safe!!! amzn.to/40god7q
@supertruckerrolling7 ай бұрын
Use a forster bit, very clean cut and no deep center hole
@Bob-bm6fn Жыл бұрын
Nice. I’m going to build this but, also use router to round off edges. Thanks .
@ianyokoro89252 жыл бұрын
Nice custom rod rack! Great addition to the "Macho Lounge"!