How To Make Automatic Water Dispenser Machine | Arduino Project

[@sauna4168]

Here is the code if someone needs it: #define trigger 5 #define echo 4 #define Relay 6 float time=0,distance=0; void setup() { Serial.begin(9600); pinMode(trigger,OUTPUT); pinMode(echo,INPUT); pinMode(Relay,OUTPUT); delay(2000); } void loop() { measure_distance(); if(distance

[@lilpoppy1328]

Thank u so much

[@sauna4168]

@@lilpoppy1328 I'm not sure if it works, i just copied it from the video.

[@lilpoppy1328]

@@sauna4168 it works! You saved me a lot of time

[@yusufchild2614]

sauNA it's the same program in the link?

[@sauna4168]

@@yusufchild2614 It's the code for the arduino. The link that was in the description wasn't working so i wrote it from the video.

[@Harvey-Specter219]

So if you did not take the glass, the water overflows right? Would there be by any chance that the dispenser stops dispensing and will trigger only if new glass is placed?

[@tretzyt4337]

there is more projects on youtube tht actually use some flow meter or some shit but it will pump exactly the same amount like 250 ml , 100ml ,etx hope it helped u

[@EvelynGomezHuerta]

Hey, can you put an image of the connected cables in the parts because they are not seen in the video?

[@anirudhadey8799]

Buddy, can you tell voltage of the battery and from in were you buy.

[@TheGameIsFunny]

Battery is 18650 nominal voltage 3.7v

[@codemelon2698]

7.2 V two cells 18650

[@wrestlingworldhk757]

And which wires you used to connect 3 pins of relay ...name plz

[@GameCastCubed]

Hello I'd love to make a auto calf feeder that each calf can get a certain amount of milk. It would work by reading the RFID tag in the calfs ear and letting them drink the allocated amount of milk. Any advice?

[@rod_ion]

Hey man, RFID has really small range, you literally have to touch it for communication to occur, you might need to use bluetooth module instead. I am actually working on some other project for cattle as well, pm me of you wanna get in touch.

[@aditia.sanjay7858]

What is the power of the soldering iron? 30 W?

[@nithinpa9514]

The motor is turning on by itself after 3 seconds , it is not reponding to the ultrasonic sensor. Please help!!!

[@adlanehichembriki220]

please share schematic so we can help you

[@universebgb]

Can you please explain how to connect two pipes

[@thiban1006]

2:17 Hello sir , I’ve followed you from the beginning, but until this code part , when I pressed upload it shows “ An error occurred while uploading the sketch” , can I get help . Im doing this for school projects, I hope I could get replies, Thank you🙏🏼

[@surya.2731]

same bruh

[@jaimecases3426]

Hello, would it still work if I use air pump that is not exactly what u used? i ordered my air pump in shopee, 6v also. Would it still work?

[@_4ishah_844]

May I have an explanation how does this thing work??I plan to make it for my school project if u would pls help me😩🙏

[@yaiba19971]

is this automatically turn off pumping water when the water nearly full or just move the cup away from sensors???

[@DCBapon]

when just away from the sensors

[@doki5855]

@@DCBapon hey mate i really need your help, so basically i need the disadvantages of this water dispenser.... since you're the creator ...i really need this for a home work and i chose to analyze your creation pls pls pls pls i will wait for your response .bye

[@jaimecases3426]

Hello I'd like to know if do I need to use a specific type of battery or I can use any type?

[@dhairya9990]

We can also use this for wash our hands by connecting that pipe to a water tank.. it will save water too 😀

[@beulin980]

I buy air pump from your link..but seems like my air pump only had 1 pipe? Why.. U had 2

[@XxXdestaXxX]

Hey pls answer my question Is this using flip flop?

[@potheadmarley1064]

Can u please post the new wiring diagram? I try to make this with the current diagram and its not working. Please post the new wiring diagram

[@lightning6255]

How did u use your pipes?

[@riojustineagustino8264]

Is there a sensor that automatically releases water when plants are detected

[@arpanmukherjee2732]

Hii dc bapon I have a doubt , plz answer. I can take the arduino uno r3 in the place of arduino nano. Plzz tell it is urgent. Plz help me out.

[@arpanmukherjee2732]

Pppplllllzzzzz tell

[@electrohardik8497]

@@arpanmukherjee2732 obviously you can bro

[@arpanmukherjee2732]

@@electrohardik8497 are you sure

[@electrohardik8497]

@@arpanmukherjee2732 100 per cent if the code and the wiring is right

[@arpanmukherjee2732]

Can you help me out

[@lightning6255]

Your wire diagram doesnt match the way ur doing... can u recheck it?

[@Wsxcvb123]

​@@pscobragaming8369nigga wtf u trying to say

[@physicswithQaiser]

Exactly... Wire diagram does not match.... Wrong diagram

[@stephdiesel2110]

Hey, I'm having troubles with the code. It appears that the file is corrupted. Possible to get any help? Thanks.

[@sauna4168]

#define trigger 5 #define echo 4 #define Relay 6 float time=0,distance=0; void setup() { Serial.begin(9600); pinMode(trigger,OUTPUT); pinMode(echo,INPUT); pinMode(Relay,OUTPUT); delay(2000); } void loop() { measure_distance(); if(distance

[@rohanandhalkar8775]

Sir I have seen some more videos about this project and I found one common thing that in all the projects rather than Arduino Uno,they used Arduino Nano.Why sir??

[@sureshjain67]

arduino uno is used in complex project

[@markfrmdao]

How did you put those hose in mini air pump?

[@wrestlingworldhk757]

Circuit diagram is not as shown in video ....which is correct ?....please reply

[@wrestlingworldhk757]

Im doing this project but not working ...please help

[@blokegogodoe]

Ive done everything exactly shown in the video. I can get the relay firing but I'm struggling to get the dc motor to activate... I've gotten it to work a couple time, but it been connected to my computer. why is it doing this? thanks in advance.

[@rbtguru]

Maybe u need to use 12v adaptor

[@Whydiskolaveri]

I have the same problem. If you were able to rectify it, what did you do?

[@SarthakChandesh]

@@rbtgurudo any wires work or just the ones in his video

[@rbtguru]

@@SarthakChandesh .any wire colour works.

[@SarthakChandesh]

@@rbtguru ok because those tangled ones look a bit odd

[@YoungEngineer07]

this code is ok but after sometime the motor is not working, i modified the code a bit and it worked well. By the way thanks a lot

[@wolffr4686]

Give me the code

[@REZ129]

Are the wire diagram correct now? Or its still wrong? Please answer its for my school project

[@cyt3495]

what is that wire called? the one that has crocodile teeths,the one that is being attached to the relay.

[@dranzy8740]

Can it be done with Arduino uno?

[@rbtguru]

Yes of course

[@sbelectronics2913]

sir can i use hear adruino uno ...? pls reply me ...!!!!

[@AnimeWarClub]

yes bro you can use

[@KRISTELLLUCIANALPEZBOLAOS]

Excuse me sir, what materials are you using for this project?

[@manojkumarj5074]

Hi, I want to know how much voltage can use this project?

[@theultimatetime8029]

@Vorname Nachname 😑

[@naveenkumar9743]

works for me thanks bro

[@pkkkk50]

Please help ...can u please tell me the correct circuit diagram

[@jvg.04]

it works but I have a problem because whenever I put the glass it stops but when i remove the glass it continuously producing water. Can you help me to fix it?

[@shareefamp6098]

Sir can i use hand wash plz reply mee

[@dydamianleng4392]

How to give a delay to the sensor to stop the water

[@DharmendraKumar-sr2eg]

Unbelievable !Nice work

[@pradeepgupta1190]

Pump me bada aur chhota pipe kaise connect hoga aur bottle me bada aur chhota dono pipe dalenge kya

[@Viewatindia]

Awesome brother but it worked na because I want also to try

[@jokebox7]

working with selenoid valve?

[@zidanfabio8429]

Is that code can be use for motion sensor (PIR)?

[@umarshaikh4393]

Will this work on Arduino uno?

[@dakshibhardwaj9922]

Sir I want to know if air pump is not available in the market what else we can use instead of air pump. Please reply back..

[@SanjaySingh-hl4ov]

Sir iski pdf file nahi mili contant num 8273262216

[@pompomboom7111]

I got the right coding and i followed all the wiring in the video,why its still not functioning? Sir?

[@DCBapon]

Exchange Relay wire connection then if you facing any problem comment me i will help you

[@marshalauzan3135]

@@DCBapon sir please help me:(. Send wire diagram new

[@aalamgarg3467]

Can we use arduino uno in this project??

[@aravindaru3534]

Hi bro i did this project by seeing your video and it's working thank you.. And how to regulate water flow I mean cutoff ... When I keep hand in front of ultrasonic sensor water flow should stop after some time...

[@seribanon3235]

Bro, can i know wire u use?

[@rbtguru]

U need to change the code and add some variable. Its a long story here

[@pkkkk50]

I did the same...my nano and relay both are glowing...but motor is not activated

[@balqisazmi5407]

were you using the same coding as shown?

[@hemantkumarrathore9014]

Sir isme agar water limit add karna h to kya karna chahiye. Mtlb agar m chahta hu ki ek baar sensor par lane par ek limit jo m tay karu utna hi pani nikle. Ye kaise hoga

[@shubhamraj4465]

there is a mistake in the circuit diagram u cannot vcc to d6 of arduin nano instead of gving to 5v

[@azumi-osaki]

The problem with Singapoor、Cambodia and India videos on youtube is DIY projects are well showed but bad hardly explained (no diagrams、no extra notes、no answers back in comment section)。I can understand that these poor countries are trying to get out of misery by creating useful things but that force us to think they are clickbait and they make money with sub-links and number of viewers "(¬ . ¬)" Maybe that I am in fault but no need to be an engineer to connect「how to show」and「how to explain」projects。

[@omrathod8487]

Can u plzz tell me where the transparent pipe goes

[@homeautomationmadeeasy3276]

Which glue did you use?

[@PriyankaSingh-mg7ty]

Gluegan

[@amrutha46]

Can some one please share the block diagram of this project! I need it to present this week

[@rbtguru]

Input : ultrasonic Process : arduino nano Output : relay and pump

[@talhacelebi1526]

@@rbtguru Hı could you help me about this project

[@pkkkk50]

​@@rbtguruplease share complete wire diagram,the diagram which u have shared is incomplete 😢

[@m1nute-videos]

can i use 12v air pump?

[@cyruscrizaldo5939]

Hi!, is it okay if I'll use arduino ATMEGA328p? if yes, is it possible if you can give me the connection of it. Thank you and have a nice day!

[@mayareddy115]

what is the use for this automatic water dispenser machine sir...plzz tell me

[@DCBapon]

you can find all link in description

[@manojkumarj5074]

Sir 12v Air pump DC motor can I use this project

[@naladoempire2252]

good evening good evening I hope you and your family are doing well, can I have the arduino code that you used for this project?

[@rbtguru]

Author already pin the coding comment.

[@manvishshetty]

can we use arduino uno instead of nano

[@rbtguru]

Yes of course

[@bosshoggett]

Would have thought a toggle switch did the same thing circuit in circuit off.

[@nihaal7750]

but this is an automatic and not semiautomatic

[@heonik123]

i have a 1 channel relay module. can it work with this instead of the model you used??????

[@rbtguru]

Yes but check the model either trigger high or trigger low.U can change it in the code

[@nuraininsofiya4057]

Sir. Your project was awesome! I already try it yesterday, but why my project run in a reverse motion? When I put the battery, the pump automatically on, but when i touch the sensor, the pump automatically off 🤔 can you help me sir?

[@yaiba19971]

switch the NC and NO in Relay

[@nuraininsofiya4057]

@@yaiba19971 thanks for your help! It works! yeay

[@rahitbiswas8929]

Yes its work my also

[@markfrmdao]

Hi sister. Did you already make this project? Can you please help me for my final exam. 😭

[@nurfaqihah3598]

Nurainin Sofiya ainin sofiya . I need ur help please ☺️☺️

[@alokitapatra3863]

Sir what's the length and height of the pieces?

[@miicoo7027]

can i buy this at shope or other website?

[@saidjaafar2796]

Why do you use relay?

[@omraja6067]

In this video how much volt u have given ?

[@jenu45]

hello i need some information how to add 2 r more aultrasonic sensor in this same project , it means how to take multi out put from one arduino nano pls help us am learner

[@lightning6255]

my arduino plate's led light is not working..it was getting connected to pc..now not.....what to do? .. how to avoid shot-ing?

[@premalathamudgal8144]

Do we get all the items

[@shailajabhale8208]

Very nice making

[@amribatu-bara5521]

I made this project ... and I have followed the video step by step ... and I think all the cables are correct. and the program has been uploaded ... but why isn't it still working ??

[@foziaafzaal5866]

R u from pakistan

[@pkkkk50]

Same here😢

[@farhanamohd9139]

How will the sensor detect its a glass and not any other object? What if there is some other object and the dispenser starts ?

[@rbtguru]

U need to add sensor at the base which is the sensor will detect glass in 2 point

[@thiban1006]

Why my dc pump is irresponsive to ultrasonic sensor

[@janeselvashani7782]

from where did the circuit got electrical connections??? is this project fake

[@rbtguru]

4:24 there is a battery

[@AlamKhan-yv5vd]

Confuse in wiring can u explain in detail right now I m just making

[@smrutihegde699]

I am getting programmer is not responding, what is the error

[@gangadharpatil7893]

Everything is working but water pump doesn't work plz tell me something......😭😭😭😭

[@seanie2361]

Can i use Arduino uno instead of nano?

[@DCBapon]

yes you can

[@artikasofi4899]

Ora kenek gagaglllll!!!!!!!!!!!!!!!!

[@vioboy21]

A very nice project but your material is not suitable for the intended machine. Use something that won't absorb water.

[@cyt3495]

pls help with the small crocodile clip,whats the name

[@prasuRangoli]

Can U apload a new wireing diagram plZ

[@nethworks2736]

Thank you its working

[@blasterking9580]

😢😢😢😢 Please my working opposite if i came glass it stop and when i away the glass from sensor it work can anyone help me i had to do please help me 😢😢

[@pkkkk50]

Please share the circuit diagram 😢

[@abylanemariefaraon9838]

Can this be done using raspberry pi? :(

[@hated8617]

I Request using raspberry pi 3

[@Liam-ok3wn]

We tried this so many times. The pump doesnt working. Only nano and relay

[@manvishshetty]

can we use ardinuo uno insted of nano

[@mujtabashaikh3863]

Yes.

[@BzEzm]

Can I use arduino uno here?

[@mortenneesgaard3233]

Yes

[@numairsayyad7816]

U get the code of this

[@numairsayyad7816]

Hello reply

[@lightning6255]

What battery u r using?

[@DCBapon]

2pcs 3.7V Li-on Battery

[@lightning6255]

@@DCBapon thanks

[@mujtabashaikh3863]

Hi. I tried making this project. The code is uploaded successfully, but the air pump still goes on working even after that. I mean, the air pump is working irrespective of the sensor. Please help... Any way i can contact you...??

[@markfrmdao]

Hey dude. Where in the same situation, did you already fix your project?

[@mujtabashaikh3863]

@@markfrmdao yes brother. The project is working all good now. If you need help regarding it, [e-mail] Is my email id.

[@markfrmdao]

I already sent a message to you brother pls check it.

[@prasuRangoli]

Hi we r takeing ur project for diploma industrial training... Can U plz post a new wireing diagram plz bcaz it's not working for my group.. we have only 3 days to submit in clg. plz sir

[@amrutha46]

Did u complete the project?

[@daniel_pe8648]

that's OK papus: #define trigger 5 #define echo 4 #define Relay 6 float time=0,distance=0; void setup() { Serial.begin(9600); pinMode(trigger,OUTPUT); pinMode(echo,INPUT); pinMode(Relay,OUTPUT); delay(2000); } void loop() { measure_distance(); if(distance

[@S.raj3740]

Please send Arduino code and wiring diagram....

[@rbtguru]

Author already pinned the comment

[@pkkkk50]

​@@rbtguruplease check wire diagram 🙏🙏 it's not the same as u did in video....not clear please send the correct one😢

[@rbtguru]

@@pkkkk50 ,i am not the one who doing this videos😳

[@pradeepgupta1190]

Isme kya program install karna padega

[@franvaz2318]

why did u solder on the wires u could have used jumper wires instead

[@sefaozgun8470]

Please help me. How can I set the water flow and stop for 2 seconds when the HC-SR04 sensor sees my hand? PLS HELP

[@atharwakumarchitnis4322]

decrease the delay

[@sefaozgun8470]

@Talha Işın Çelebi çok uğraştırdı ama yaptım

[@sefaozgun8470]

@Talha Işın Çelebi üstünden baya geçti projemin sadece malzemeleri duruyor kodları vs hiçbiri durmuyor. yine elimden geleni yaparım

[@sefaozgun8470]

@Talha Işın Çelebi hocam ben kafama göre yaptım onları strafor ile ölçüleri bilmiyorum tabanın 2 katı boy yap

[@antifragile-tz7oh]

Can i know what is the size of tube? Please i need it for my school project.

[@rbtguru]

Based on your pump nozzel size

[@antifragile-tz7oh]

@@rbtguru oh thank you😊😊. You tell me this eventho i almost finish my school. It's very helpful😚

[@rbtguru]

@@antifragile-tz7oh better late than never😂😂😂

[@S.raj3740]

Can we use Arduino uno

[@rbtguru]

Of course yes

[@Virtual-Classmate]

Within this week I need to complete my project. Plz help me out

[@amrutha46]

Did u complete it?

[@muhdkhairulanwar9265]

Does the program works on arduino uno?

[@Ooo-b5b1b]

I have the same Q