How to make BLDC motor ESC using mosfet

Schematic diagram: drive.google.com/file/d/1wkOV...
The idea of creating a brushless motor control circuit
Brushless motor speed control
Everyone has suggestions to make the circuit more complete

[@D.creative]

My ideas: kzbin.info/www/bejne/qZaQg6ube6qhmbs

[@worldsbeauty472]

Dear! Please make a hoverboard motor controller.

[@lovenish7523]

Hello

[@lovenish7523]

How much ampere this can carry.

[@D.creative]

@@lovenish7523 I haven't tried it at full capacity yet

[@lovenish7523]

@@D.creative ok

[@averagecornenjoyer6348]

I was thinking "wow, pretty cool" until you shipped out the custom soldering iron and then, that earned you a goddamn.sub

[@dixonq5828]

The Mosfet terminal D (middle one) and the screw hole metal are the same connecting conductor, it is important to show how isolation is done between the screw and the body of the heatsink. Otherwise all D terminals will be shorted.

[@Jitshri]

Thank you very much for this circuit diagram

[@MaxImagination]

Excellent... I just happen to have everything for this project, awesome one!

[@D.creative]

Thank you!

[@user-Ammar1996]

Did you build the controller and did it work for you?

[@dgb5820]

Thank you Sir for the schematic really appreciate your knowledge base

[@simul7md991]

شكراً على الفيديو المفيد اتمنى الاستمرار 🌺

[@Philly_Gamer]

Great job! Plus your build quality is art. Awesome!

[@D.creative]

Thank you!

[@jayshaw3971]

好嘢❗有料到❗谢谢你的视频。china HK

[@dalipsingh5780]

Very nice video about bldc motor.voltes.control thanks sir

[@amosshaibi2216]

I like it, i’ll give it a try

[@paksalim1061]

Mantaf nih bos.keteranganya tutor nya jelas pelan bisa dipahami.editan vidionya mantaf.bisa motong durasi waktu❤

[@kakangmas_ari6336]

dah coba blm lu bang?

[@marisakirisame867]

this thing could power up my prop plane and thank for the tutorial

[@Dr.PKSachan62]

Nice video, nice technology, meaning full video...., Learning full video...

[@sadunnakipoglu9471]

أشكرك وأقدر مجهودك ، تحياتي لك من تركيا.

[@vikasazad08]

Love from India 💖

[@medaturbo9899]

Thank you nice explanation, patient shot

[@paulneilson6117]

Thanks. I'm installing this in my hoverboard to spin the liquid metal ring with some magnets.

[@georgeyoung613]

Very cool project. Excellent build quality. 👏

[@XavierBetoN]

Nice video! One question: how do I make it stop? I've been looking to implement on/off burron to the slide potentiometer to use it as 0-100% motor driver and still need help

[@danielramirezcruz.2209]

Fantastic video l love it thanks.. super video me encanta mil gracias por compartir..

[@D.creative]

Thank you for watching!

[@sunilnagindas9236]

thanks for sharing your circuit. What is your input voltage?

[@ModeratelySpeaking]

This is very impressive! I want to be able to do a scaled up version of this, for say a 5kw BLDC, to work for my boat conversion. I don't really know the 2nd thing about this stuff. Anyone willing to share their wealth of knowledge? I intend to use ebike-type parts but obviously throttle grip speed controller is t gonna cut it for a boat. A foot pedal could work, but is also not ideal. Any ideas?

[@thomashardin911]

<a href="#" class="seekto" data-time="284">4:44</a> what kind of soldering gun is that, where did you get it?

[@user-fz8gj9ry7z]

В 60х годах в СССР был асинхр.дв на ГТ403 на магнитофонах весна 202 тот был прорыв в радиоэлектронике желаю вам успехов

[@poyen_tseng]

Anyone also came from Greatscott's video?

[@DanielA-cr1kr]

Thanks for video, how many watt is the resisstor 4/7?1/4 or more? I

[@jordanseegrist8142]

thank you for the video. How can I determine the appropriately sized components to use for an approximately 2000 watt brushless motor?

[@Ozzy3333333]

You do not want to use this for a 2KW motor,why, it don't have good control, and a 3hp motor you want control, at least I hope so.

[@profrefaey]

thanks for your effort, I did everything but the potentiometer doesn't affect the speed!.......and if I have a motor with three wires only how I could connect it?

[@alvarofuentesarjona2668]

Excelente el video por su limpieza. Me acabo de suscribir.

[@melplishka5978]

Nice job bud ty.

[@ostanin_vadym]

Thank you for content

[@jayshaw3971]

好嘢❗示范手法一流❗china HK

[@D.creative]

Thank you!

[@Qui-9]

Why does this work, and how did you know it would, before building it? What causes the commutation? Does each section sense the electrical behavior of the next/previous driver/coil?

[@angelcoimbra8313]

muy bueno, cuantas son las rpm mínimas que se pueden obtener?

[@menglee3320]

Can you make the motor go forward and backward? And if you can do it; try to slow down the motor so we can see what direction is turning.

[@cyberbeast1789]

can i use this with 12v battery as power source?

[@cellphonerepairing2111]

Nice work full support your channel

[@D.creative]

Thank you!

[@jimbossemi-customs3129]

Excellent informative video my friend! Subbed and the bell on for future videos! I know you are probably very busy, but would you know how to control a larger DC motor out of a treadmill? Someone gave me the motors but they didn't save the control panels. Thank you!

[@snehanshourya3850]

What kind of motor is it? Brushed or brushless? If it has 2 wires, it's probably brushed. If it has 3 wires then it's probably brushless. If brushed, you can use single switch PWM even without filters. Just remember to put freewheeling diode. Brushed motor control modules are also available for sale. If it's BLDC, you are better off buying a BLDC controller rather than trying to build one (if purpose is learning, surely try building one).

[@ranjithalumullithody]

Please do a video on three wire bldc drive circuit

[@Sandor338]

Excelent !!

[@MRAVIPRO]

You somehow made the video, you made the circuit money, that's how you made it ..

[@dmitryw7880]

Very simple and nice!

[@kamusih4336]

Many thanks

[@gamzeakdag796]

Hello , Can I also use this circuit in x4108s 380kv brushless drone motor?

[@burpcoolgt8622]

How about with 2 mosfet? Can its work?

[@SakellarisNikolaos]

excellent 👌 what RPM can speed?

[@fsh77]

What is the function of the diodes installed from the gate to the drain?

[@aedi_project_indonesia]

what dynamo is that? Thank you in advance

[@yongkeechia1834]

How low can the rpm goes? May I ask

[@gilvanmarinho514]

Bom dia! pode substituir o IRFZ 44 por IRFZ 48 ?

[@bariqrizwan8716]

We can use irfz44n mosfet ?

[@LordMarinade]

<a href="#" class="seekto" data-time="188">3:08</a> I guess you can't replace the potentiometer with JR servo wire connector to stick it into the reciever and have working RC ESC?

[@mohmen3191]

Thnx brother it's great job but i have question this bldc is for 4 wire connection witch named start connection please can you make tutorial to bldc for 3 wire who named delta connection... Thanks a lot of i like your videos 😉

[@CongOanhVlogs]

kzbin.info/www/bejne/oJzFfmybr6pnoJo

[@Ozzy3333333]

@@CongOanhVlogs spammer, reported

[@James-qw7hp]

kzbin.info/www/bejne/jIbUh4J6g8yCfLM

[@HenrikHvalpen]

Nice but would like a follow up step by step how to find the right components.

[@pafunleal3849]

Hi Sir author Can u please anwer if mosfets IRF540 can be used instead of 3205? Also, the diagram in the end of the video is covered by pictures of next videos. Can you please put the diafram in a file and share? I will try to software simulate this circuit to check other parameters and help to improve it Thanks a lot for your effort and great work Best regards

[@D.creative]

drive.google.com/file/d/1_3KGGnX_jgZ8AkcuOWk7iJqKZ2ltq8n2/view?usp=sharing

[@pafunleal3849]

@@D.creative You are very kind and generous, sir. God bless you

[@Fernybeme]

You just need to make sure the source drain and gate match on both transistors and you should be fine.

[@pafunleal3849]

@@Fernybeme Hi, thanks for your reply. I have tested with both IRFZ44 and IRF540 and they bothe turn the motor at a voltage higher than 5V. I used 8V

[@Fernybeme]

@@pafunleal3849 awesome

[@nabilshamaa1697]

Good job please can give the circuit diagram of the of the system

[@gunaratna123]

Can I use stepper motor instead of HD motor?

[@user-xi8hb2bz8j]

Good

[@ethanhensley1722]

Is this considered 4 phase controller?

[@abrahambello7043]

Has uno para el de 3 pines? Ya compre todo los componentes para armar el mio

[@analys7622]

Hay quá bạn, đỡ tốn tiền esc +1 sub

[@James-qw7hp]

Nice

[@Hi-lz7wo]

Does it matter how big the heat sinc (is sinc spelled this way?) Is?

[@kalubibondo1891]

Verry good!! does this Controler support load on it?

[@D.creative]

yes sir. Thank you for watch

[@Littleaac]

Thanks for this

[@sandeepyadav1602]

Blue, yellow and red wires are sorted to each other. Hows it running!😢

[@pierpa_76pierpaolo]

URGENT!!! I am looking for an audio pre-amplifier capable of 300\400 times gain. There are several diagrams in the N.E. manual with explanations, and it can be nerve-wracking to stand there with formulas to be able to find the ideal Rx value ..... . The LM358 IC is great but I would like to know what is it capable of doing? What max results can be obtained? In short a noise or a voice at a certain distance .... . How to get it as close as possible and then run it through an 'AB' type amplifier. But what wattage is needed ....... ? Thank you very much.

[@Whyyouhere_]

Can we use 12v? And another question is the power supply is DC or AC because I've seen people are using AC to let it spin without ESC

[@D.creative]

We can use 12v. is the DC power supply. This circuit can be used for big motors: kzbin.info/www/bejne/qZaQg6ube6qhmbs thank you for watching!

[@Whyyouhere_]

@@D.creative much appreciated your work

[@classicnetwork9552]

How to use this circuit in three wire hdd ?

[@noutram1000]

Can you explain the working of the circuit please (I know how to solder...)

[@Muzzaymann2260]

Wow thanks really helpful, please what's the rpm of the motor at 9v. Thanks in advance.

[@jaibhagwanjangra3803]

Very nice my

[@navaneethrnayakcse4568]

Great job!, 9v how much amp required ?

[@D.creative]

0.5A -1A. sir

[@Dancopymus]

Very cool! Maybe I'm wrong, but it seems that to get more Motor speed you are turning the Potentiometer knob to the opposite (left) side? Another thing, is it not possible to stop the Engine completely? Thanks for sharing.

[@Dancopymus]

I asked you two questions!

[@user-uq3vy1hr8i]

Like you for the diagram! There is no 4.7 kOhm resistor on the diagram, but there is one in the video. Why ? I repeated it exactly from the video - it works, but the motor itself does not start - you need to push it. I supply 9 volts from a laboratory source. Why not 12 volt power?

[@emilioloboprincipe9637]

Good work, electrical energy ¿? CA and DC??👍👍

[@hugoatieni9036]

Muy bueno

[@WimTon]

The video at <a href="#" class="seekto" data-time="349">5:49</a> suggests a star configuration for the motor coils. However, delta configurations are also common.

[@imnotbeluga007]

This circuit simply isn't compatible with a delta configuration. A delta configuration requires current to flow through 2 coils, and this only does one, and to the common central point. You'd need 6 transistors and a microcontroller to control that - you've just made an actual ESC that you can control!

[@mashadi26]

Can it turn the spin CW to CCW?

[@relaxme3951]

What did you screw the mosfit into does it have to be specific metals and does the screw you use have to be conductive?

[@D.creative]

you are skeptical: kzbin.infocej_8mQm17A?feature=share

[@relaxme3951]

@@D.creative Thank you for the amazing video... i finally made it work. For anyone stuck after youre sure the wiring is correct try increasing the amperage that fixed it for me :D

[@olegv.5173]

explain where the impulses come from? If there is no generator? Sorry, I figured out the circuit, it's a 3-phase multivibrator

[@janami-dharmam]

But there are no capacitors! multivibrators need capacitors for reliable operation.

[@olegv.5173]

@@janami-dharmam You're right bro!

[@James-qw7hp]

kzbin.info/www/bejne/jIbUh4J6g8yCfLM

[@user-Ammar1996]

Did you build the controller and did it work for you?

[@ebrahimalipour3123]

Tanks for sharing.this circuit working for copier 24v bldc motor sim another video 12v motor you showing?

[@tinhnguyenhuu7183]

Cám ơn video

[@matejgamingandotherstuff6484]

You should use plastic screws with your insulations

[@Ozzy3333333]

There is white insulation washers that make it not short, otherwise it would not work.

[@matejgamingandotherstuff6484]

@@Ozzy3333333 but he used metal screws which could touch the heatsink from inside the hole

[@Ozzy3333333]

@@matejgamingandotherstuff6484 he is using a special insulation washer, it keeps the metal screw from touching the fet metal tab, its hard to see in the video, but its there, these are very common in power supplies.

[@matejgamingandotherstuff6484]

@@Ozzy3333333 but the screws are metal

[@Ozzy3333333]

@@matejgamingandotherstuff6484 and the washers are insulators = providing insulation, look them up, you will understand.

[@roca36maxx]

cuantos amperes soporta?

[@flaviocosta5767]

Work Hub motor ir e-bike?

[@Morbrine]

How many amps can this circuit handle?

[@user-RK1648]

Thank Q brother

[@КОБА757]

Респект 🔨😎👍📽️🔥🏁🚩

[@andrericardobarbozapereira]

Can you feed this project with 12v?

[@D.creative]

Yes! kzbin.info/www/bejne/qZaQg6ube6qhmbs

[@lilsavage6807]

Man thanks

[@eng.shh80]

What about the motors with only 3 wires (UVW) without neutral wire (N) ? Does this circuit work ?

[@D.creative]

No sir

[@AS_Bonsai_escuela]

U, V, W van a los mosfet pero si todos los tornillos están conectados al disipador están todos unidos? Lleva algún separador aislante en el tornillo?

[@mbol4348]

are isolated with plastic rings

[@ayhanozsoy8772]

some HDDs are 3 phase instead of 4 phase, how should its connection be thanks

[@donatellodonati4525]

Hi, I have just finished my mosfet esc as on your video but it does not work can you help me find the reason for this. When I give it power the hard disc motor stutters for a second and stops, if I turn the potentiometer it squeeks but doesn't turn, same with other 4 motors. Thankyou Donatello

[@catotv5368]

I have the same problem I think this video is not real

[@D.creative]

You need to adjust the voltage accordingly for each different motor

[@D.creative]

kzbin.info/www/bejne/qZaQg6ube6qhmbs

[@James-qw7hp]

kzbin.info/www/bejne/jIbUh4J6g8yCfLM

[@jao_baixinho]

Esse circuito vai precisar de quantos Amperes?🇧🇷

[@D.creative]

sir, 0,5 - 1 ampe

[@jao_baixinho]

@@D.creative ok, obrigado!

[@baburamabadhran1437]

Can ESC be made with 2 mosfets and a thermistor . ??

[@abhikpandey7092]

Bhai heat sink used all terminal of moter short how your project work

[@liil5311]

Can you use this one at three face brushless motor wire