How to Make Cheap Single Cell Battery Powered RC Airplane.. Homemade Airplane

Can the entire system including the Motor, Servos and receiver be powered by a single cheap 18650 3.7 volt battery?
How To Build The Simple RC Airplane That Can Fly With 3.7V Single Battery.
* 20A ESC: s.click.aliexpress.com/e/_DFg... OR
www.banggood.com/custlink/mvv...
* 9gr Micro servos: s.click.aliexpress.com/e/_DDe...
* 5gr Micro servo: www.banggood.com/custlink/mGD...
* 1.2mm Pushrods: s.click.aliexpress.com/e/_Ded...
* Servo control horn: s.click.aliexpress.com/e/_DmJ...
* DC 180 Motors : s.click.aliexpress.com/e/_Dd1...
* 108mm Propellers (CW&CCW): s.click.aliexpress.com/e/_DeI...
* Radio control system: s.click.aliexpress.com/e/_DCP... or * tr.banggood.com/custlink/vvGE...
* Micro receiver: s.click.aliexpress.com/e/_DEX...
(18650 Battery 1500mAh+ & 4A+)
* 18650 3.7V Battery : s.click.aliexpress.com/e/_Dno... OR www.banggood.com/custlink/KDG...
* 18650 Charger: s.click.aliexpress.com/e/_DEI...
* Hot melt Glue Gun: s.click.aliexpress.com/e/_DkC... OR
s.click.aliexpress.com/e/_DnD... OR s.click.aliexpress.com/e/_Dl2...
* JST Connector&Cable: s.click.aliexpress.com/e/_DmT...
* Cable Tie: s.click.aliexpress.com/e/_DBI...
5mm kraft foam board
3mm insulation foam
2mm balsa sheet
Diagrams for dimensions: tinyurl.com/95mc2hjh
Technicial Specifications:
Wing length: 88 cm
Body length: 65 cm
Wing area: 1056.00 cm2
Flight weight: 192 g
Center of gravity (CG): 4.7 cm - 5.3 cm from the front of the wing
Vbar: 0.86
Motor: DC 180 Brushed
Battery: 18650 3.7V
ESC: 20A Brushed
Remote control: 3 channels or higher and 2 micro servos
Approximate flight time (for 2600mAh) : 20-25 minutes (in ideal conditions)
#rcairplane #diyairplane
All of my videos : bit.ly/2Z9QVYK
Thank you for watching. Please Remember to Share and Subscribe for More Amazing Videos.

[@notniko6914]

I loves watching these vids as a kid, now that I'm a electronical engineering student, this is even better to watch!

[@LordMarinade]

omg man hearing that ESC beep beep beep from the brushed motor gives me so much nostalgia from having my slow flyer propelled with Mig 400 motor, I'm glad that I got to learn using BLDC motors but damn this is really cool and nice little build for beginners

[@BradleyWest435]

exactly so much memories

[@peruccaeditz]

Nice build and flight,hats off to you👏🙇

[@NovgorodskyLeatherCraft]

Nice job, sir. Thanks for sharing.

[@michaelwhinnery164]

I've done a Couple scratch builds also , and they are always fun. Also there is no soul crushing heartbreak when you crash, because you can just easily fix it or just build another one.

[@therobloxyoutuberfunny]

Please help me how to build a perfect balanced plane with a fly robo kit 😅

[@PakiNewsNetwork]

How do I thank you for this? Now I WILL build a plane.

[@sonsuzevren61]

harika oldu.. teşekkürler ve tebrikler...

[@seanheadrick]

that was a great video Thanks!

[@jackjuhasz533]

Brilliant design and great video !

[@arekporongkluyuran]

Anda luar biasa...., Saya berharap lain waktu anda membuat rc glider atau slow flyer dengan bahan depron menggunakan dc motor, pasti itu akan sangat menarik, terima kasih

[@SEMOLANG]

Gerçekten mükemmel ! Sadece 3.7 volt ve bir şaheser

[@marcwibble7949]

Enjoyed that thanks even like the music

[@neerajkakar8104]

Good flying airplane !

[@RC-Heli835]

Neat! Tall grass is your friend there in he end. Of course its so light and slow that it would be hard to destroy it.

[@JoseA-Divergent]

Muy bueno! Usas la 18650 como bateria en lugar de las Lipo..... Yo tambien las uso y van de maravilla. El diseño del modelo le *Aumentaria el Diedro y la distancia entre el ala y el estabilizador de cola* ..Asi seria menos Nervioso... Salgo a volar! DX

[@AyhanErkin]

Eline sağlık...

[@ayoubessadi2904]

عمل رائع واصل ❤️♥️🌹

[@kenspaceman3938]

Lovin it!

[@tr_dm]

Amatörler için çok ideal bir alıştırma modeli olmuş eline sağlık👍

[@flymaster_tim]

Wow! Maybe I will make it

[@JirawatSu]

nice work.

[@thisisnotmyname4700]

So cool ❤

[@fadonmc1737]

abi muq olmuş herzamanki gibi

[@mitsos306ify]

I pushed like before I saw it!

[@ss9767]

Çok güzel uçuyor tebrikler...

[@aquaonx8784]

npc

[@stinger4712]

Me and the kids are lapping this up. They'll get building and we'll show you what we've built based on your inspiration

[@therobloxyoutuberfunny]

Did u build it buddy?

[@snax_4820]

You are a genius!

[@Zghost276]

The people who invented rc are genius

[@kaansoysal1881]

Başarılı 👌

[@beallrounderbd]

Amazing

[@grumpyjohntxredneckrc6346]

Nice... 👍👍😁😎

[@M5guitar1]

I dig slow fliers.

[@romanhunka6021]

super❤😮

[@volkankavas9350]

Çok büyük hayranızım tebrik eder ve daha çok video yüklemenizi sabırsızlıkla bekliyorum...

[@RohitKumar-kc2pq]

Which language are you taking bro/sis

[@MalKediler]

@@RohitKumar-kc2pq Turkish

[@rizaltawani93]

very inspiring !

[@fatihp5887]

İlk yorum benden olsun 😊 aga yine yapmışsın yaa 👍

[@meocat7223]

Great, Please make coreless motor plane, thank

[@meIanchoIia]

Hey I've been watching your videos since long and it's really great.. i've a question, does the motor create all the thrust or the large wings inclined at an angle with the horizontal axis contribute some upward lift too ?? I'd be grateful if you answer

[@Kendin-Yap]

The motor provides the propulsion. As long as there is thrust in the forward direction, the lift force of the wings occurs in the upward direction. But after the engine stops, some more gliding continues.

[@nedimbuyukafsar6434]

👍👍👍

[@spottyjack614]

Hi..nice build. I have a question..so rhe micro receiver u used in this build it paired up to your flysky radio even though it's not a flysky receiver??? And that being said I'm guessing you bind that receiver to your flysky radio the same way you bind a flysky receiver to your flysky radio??thanks....

[@kushanvimanka8323]

FS2A four channel receiver is using AFHDS 2A protocol so it can be bind with flysky transmitters, I also having it and works really well.

[@Kendin-Yap]

Yes, a receiver (FS2A) for Flysky radios. Matches like other Flysky receivers.

[@spottyjack614]

@@kushanvimanka8323 I have to get me a couple of these FS2A receivers for my fly sky radio do u have a link to were to get them?? If not I'm sure I can find umm somewhere?? Just thought I'd ask...thanks

[@balfasladicra5270]

can i use 105mm for propeller?

[@alonblumental6054]

VERY NICE! why didnt you cover the bottum side of the wing? withiot this cover the lift is damaged and making a lot of turbulence on the wing.

[@Kendin-Yap]

Thanks.. I made this to be lightweight. In addition, this (Concave profile) allows it to fly at very low speeds. It is not wrong to have an open wing.

[@nichtolarchotolok]

I have a question since I have been planning on following this build for my project. Will the 20A esc work on a single 3.7v battery ? the product specs say it takes 4.8v-7.6v and this has confused me a bit. Also, does the ESC have a BEC to power the arduino based receiver? Its hard to source smaller bldc motors where I live and I want my build to be light enough to work off a single cell. I am also planning on trying make an rc car from a die cast model (bigger than hot wheels so space is there for arduino and everything). Hope you see this and reply.

[@Kendin-Yap]

When the 3.7V battery is fully charged, it is 4.2V. This ESC can work up to 3.9V. BEC available. But your receiver and servon must also be able to work with low voltage. The ones I used in the video can work.

[@nichtolarchotolok]

@@Kendin-Yap THANK YOU SO MUCH for the reply. I just got the batteries and ESC in the mail and tested and it works. The concern i have is if the Arduino based receiver I'm planning on making will work well. My arduino nanos seem to work fine but i am yet to test the nrf24l modules and servos.

[@Yuvraj_makwana_]

Thanks❤❤❤ i can make this plane into my budget😅❤

[@adityabaghel729]

ye dukh kahe khatam nahi hota be 😢

[@michaelwhinnery164]

I cannot believe you left out the all important CG !!!

[@phamlocnhan5472]

THANK

[@nuricetin8398]

Abi selam antalya dan balıkçı ben

[@adityabaghel729]

Sir, can I use that DIY rc transmitter and receiver in this project that you have taught how to made it earlier ?

[@Kendin-Yap]

It is a little heavy. This model has to be very light.

[@nurullah6025]

❤

[@user-rp3fc4dh7c]

Интересно, но такое впечатление, что управление осуществляется с помощью ветра :)

[@sajidakilledar779]

Hey u have used 9gr servos which work with 5v but the maximum power supply is at full charge 4.2v so how did they work?

[@Kendin-Yap]

These servos can operate up to 3.8v-3.9V level. It loses some speed and torque, but that's not a problem for this model.

[@hasancakal4337]

Abi bu tarz videolara devan

[@saitaltun6526]

Çok güzel bir video olmuş... Aynı malzemelerle delta kanat videosu da gelir mi acaba?

[@cesarca1102]

I have watched your video many times and followed the guidelines for my plane. I had problems with the radio because I had to hold the "Cancel" key longer to save the configuration. 🙂With 3.7 the engine has no power. Maybe because the other elements subtract energy from the engine? So I put a 7.4 battery in it and it sounds better. But won't the motor burn out? thanks for answering

[@Kendin-Yap]

When a 3.7V cell battery is charged, it will be 4.2V. It should be fine until it drops to 3.8 - 3.9V. Since the engine will produce high power when 7.4V battery is used, the structural strength of the fuselage and wing of the aircraft will not be sufficient. This model has to be very light in order to fly with low power. Therefore, it does not have the structural strength required for high strength. If you are going to use it with 7.4V, you need to strengthen the wing and fuselage. (Can work with DC 180 motor 7.4v.)

[@cesarca1102]

@@Kendin-Yap You are very kind to answer. It's clear to me from other answers you've given. Thank you

[@RangerPeeps]

Very impressive, how do you land it though?

[@luigimario2704]

Crash

[@luigimario2704]

Do it parallel with the ground though

[@xsy8091]

Abi ben Arduino ile kumanda yaptım 3 km ye kadar basit RC uçak uçurdum fakat şimdi 2.38 boyunda yapicam 2 kg a yakın bir ağırlık var 2 adet 1400 kv motor ve 1045 pervane ile kaldırabilir mi acaba ?

[@Xkite51]

Wow

[@crescentcabbage8065]

Hey, so I’m doing this for my science fair and while I was connecting the battery to the esc the esc started smoking. Do you know why? The battery is 4.2 volts - 5 volts, I think that was the issue but I’m not sure.

[@Kendin-Yap]

ESC supports up to 8.4V. The problem is not voltage.. You must have connected the positive and negative poles wrong. Another possibility is that you may have short-circuited the motor output cable ends. In both cases, ESC burn up.

[@crescentcabbage8065]

@@Kendin-YapOk, thank you it works now. The only problem is I used cardboard for the whole thing and the plane won’t fly or glide with the wind. It fell and the cardboard body is destroyed any recommendations?

[@BradleyWest435]

@@crescentcabbage8065 use deprons bhai

[@crescentcabbage8065]

@@BradleyWest435I used the Kraft foam now for the body. Unfortunately, I couldn’t find any 3mm foam for the wings so I thought of using 3mm Eva foam but that bends too much and isn’t structurally strong. The plane still doesn’t glide and falls. Have any ideas what I did wrong and why it doesn’t fly.

[@pawanchand7382]

Rc plane Boeing make video sir plz 🙏

[@emredemirelsworld]

Emeğinize sağlık çok net anlatmışsınız, motor itme açıları her uçakta aynı mıdır? Arkadan itiş fpv modeller için açıkar hangi yönde ve kaç derece olmalıdır?

[@Kendin-Yap]

Burundan çekiş için genellikle bir birine çok yakındır. Arkadan itiş de ise değişir. Örneğin bazı yapılarda yukarı açı gerekir. Kesinlikle şöyle yapın demek zor.

[@emredemirelsworld]

@@Kendin-Yap teşekkür ederim 🙏

[@serdar-bayram]

Elinize sağlık hocam çok güzel olmuş , uçuş süresi nedir acaba. Birde hocam , motorların üstüne lehimlediğiniz 2 parça ne işe yarıyor .

[@huseyin985]

2:47 de yazıyor. "elektriksel gürültüyü filtrelemek için."

[@esatkdn]

seramik kondansatör. paraziti engellemek için, motor gerisinde olan devreyi korumak için, motorun daha iyi çalışması için felan

[@serdar-bayram]

@@huseyin985 Teşekkür ederim gözümden kaçmış, Bazen motor daha güçlü olsun diye buna benzer parça lehimliyorlar acaba odan mı diye sordum bende.

[@serdar-bayram]

@@esatkdn Anladım , çok teşekkür ederim.

[@Kendin-Yap]

Yeterince cevap verilmiş. Biraz daha açayım. Motorların bobinleri çalışma esnasında elektriksel gürültü (parazit gibi) üretirler. Bu gürültü elektronik devreleri özellikle alıcı gibi devrelerin sinyallerini olumsuz etkileyebilir. Seramik kondansatörler bu gürültüyü filtreler.

[@abhijitumakkar87]

i think this is the first 1s li ion plane

[@tibib4029]

Cuanta autonomia tiene con la 18650 ??? De cuantos amperios es ?

[@Kendin-Yap]

Current strength should be 10A or above. The capacity varies according to your preference.

[@Sunnyfpv1617]

First

[@zecsabbath7160]

que receptor é esse ?????

[@v4vinz]

what kind of board did you used for the plane

[@Kendin-Yap]

Kraft foam board and insulation foam

[@sportmenmen7016]

Selamunaleykum

[@TheSlicedSock]

Can you give a link to the foam

[@philippe5394]

@KendinYap. Hi Sir, I'm about to order the parts to build my first airplane, the "Single Cell Battery Powered RC Airplane." Something is calling out to me. The recommended voltage range for the ESC is 4.8V to 8.4V. You're using a single 3.7V cell. How do you explain this? I'll read you carefully before finalizing my order.

[@Kendin-Yap]

Every ESC has some flexibility in the positive and negative direction. When the single cell battery is fully charged it is 4.2V. The ESC I mentioned in the link works smoothly up to 3.9V. I tested it for a long time and had no problems.

[@AlfieEdits420]

What is the end build cost?

[@coast219]

How can the esc which is rated for 4.8v functions on 3.7v?

[@Kendin-Yap]

When 1S battery is full, it is 4.2V. And these ESCs have voltage flexibility. It works fine until it drops to 3.8-3.9V.

[@coast219]

@@Kendin-Yap thanks👍

[@Chennaijohn]

Hi hello sir

[@ismailkara2482]

Slm fpv drone için farklı kumanda olur mu

[@bq15096]

2:29 and 4:45 ) Where can i buy that red and black cable on the battery / motor??? and also at 3:05 we can sea on the motor that black cable with red where can i buy that en how does that fit there??

[@Kendin-Yap]

I added it to the links. Please check again

[@S.M.A99]

Can I make this with 1000kv bldc motor?

[@Kendin-Yap]

No, it is not suitable.

[@bq15096]

For the Control / Radio system from Aliexpres witch version i need for this plane? because there are a lot off versions

[@Kendin-Yap]

You can get the one marked "No Receiver". Because you need to buy the micro receiver separately.

[@cellatayberk9347]

Motor olarak ne kullandınız acaba vidyoda belirtmemişsiniz???

[@Kendin-Yap]

Videoda mevcuttur. 2:28 ... ayrıca videonun altındaki açıklama bölümünde tüm parçaların isimleri ve linkleri de mevcuttur. videonun altındaki açıklama kısmında "DAHA FAZLA" ifadesine tıklayın.

[@embs7979]

Merhaba bu uçağın aynısını sadece pili değiştirerek 7.4V 1000mAh pil ile yapabilir miyim?

[@Kendin-Yap]

Mümkün ama uçağı biraz sağlamlaştırmanız gerekir. Çünkü 7.4V ile motor gücü baya farkediyor. Kanat altını komple 3mm depron ile kaplarsınız. Ve kanat içine boydan boya 3-4 mm kalınlığında bir çıta koyarak destek yaparsınız.

[@omercoskun7851]

Herşeyiyle çok güzel bir model olmuş fakat fiyat açısından şu ankı kullandığınız kumanda yerine daha uygun nasıl bir kumanda tercih edilebilir

[@Kendin-Yap]

En uygun fiyatlı kumandalar Analog olanlardır (Menüsü ve ekranı olmayan). 4 kanallı bir anolog kumanda ile temel bir çok model uçak kontrol edilebilir. Markası önemli değil. Diğer seçenek arduino ile kendi yapacağınız kumanda olabilir.

[@kubraaltundas8760]

Merhaba iyi günler, Videonuz da kraft fotoblok kullanmışsınız.Bu maket uçağını bizde tasarlmak icin malzemeleri temin ediyoruz yalnız kraft fotoblok degil strafor fotoblok aldık uçuş için herhangi bir problemle karşılaşır mıyız

[@Kendin-Yap]

Strafor çok esnek olduğu için rigit bir hale getirmeniz lazım. Karbon çubuk veya benzer bir malzeme ile destekleyebilirsiniz. Özellikle de kanadı.

[@kubraaltundas8760]

Teşekkür ederim.Kraft fotoblok temin edelim .Maket uçağı uçururken karşılaşacağımız büyük problemler neler olabilir.Yardımcı olursanız cok sevinirim

[@spacelovers472]

Pil kaç mAh ? Ve ne kadar akım vermeli ?

[@Kendin-Yap]

4A ve üstü akıma sahip olmalı. Kapasite önemli değil. Tercihinize kalmış. Çünkü 18650 pillerde kapasite ağırlığı değiştirmiyor. Benim kullandığım 2500 mah

[@owengrossman1414]

Why not put the servos as far forward as possible?

[@Kendin-Yap]

For the center of gravity.

[@venkatratnakar685]

Hi There....i need your help...i followed the instructions but 5:53 to 7:22. But FC-16X is not remembering the setting. CH3 still goes complete back n forth and not able to see any power to Motor. What am i doing wrong? Could you please guide? Both reciver and ESC have flashing blue (slow) and fashing red and it only makes 1 DO sound.

[@Kendin-Yap]

If you are talking about FS-i6X, you need to press and hold the CANCEL button for a long time to save the setting.

[@venkatratnakar685]

@@Kendin-Yap Thanks so much for responding. Got it able to pass that one. But still no power is going to motor. ESD board just makes one DO beep but nothing past that, unlike in your video DO BE MI (7:36 to 7:43). Could you please help, if the issue is receiver board or ESC Board? i ordered another set just in case. Battery is fully charged 4.18v , Now reciever light is blinking slow (so should be connected). Any suggestion will be very helpful

[@venkatratnakar685]

@Kendin-Yap Could it be the ESC board not working? I just not able to figure out if the receiver is the problem or the ESC board. Shipping is taking time. Any suggestion will be helpful!!

[@venkatratnakar685]

@Kendin-Yap: Thanks for your help. Realized the issue with Transmitter and Receiver were not binded. After doing the binding process it started working.

[@denizvural163]

Atılan uçak olarak da kullanılabilir mi?

[@dogukankocak1822]

ağırlık merkezini iyi ayarlarsan olur

[@mehidiadjel559]

What is the name of the material used to make the frame

[@Kendin-Yap]

Fuselage: Kraft foamboard. Wing: insulation foam

[@PePDude]

Whats the weight of that rc?

[@Kendin-Yap]

192gr

[@nuricetin8398]

Bizim normal 6 kanal fly sky 3.7 ile çalışmıyor galiba

[@Kendin-Yap]

Çalışır ama menzil önemli ölçüde kısalacaktır. Tüm alıcılar için ideal voltaj 5-6V dur. Yaklaşık en az 3-3.5V a kadar çalışırlar ama menzil kısalır. Bunun gibi kısa mesafede kullanılan modellerde sorun olmaz.

[@baykemal7874]

Merhaba 1 adet dc 180 motor kaç gram itiyor veya çekiyor ortalama 100 mm pervane ile?

[@Kendin-Yap]

Yaklaşık 140-160 gr

[@baykemal7874]

@@Kendin-Yap süper, teşekkürler.

[@robertosabatino7213]

👏x💯

[@oguzhanarslnx]

Hocam kumandayı kendim yapacagım pcb yide ben tasarliyacagim. Hangi parcalara ihtiyacim var antenli. Nrf kullancam yazar misiniz lutfen

[@Kendin-Yap]

Kumanda yapımı videolarımda malzeme listeleri mevcuttur. Onlar size faydalı olacaktır. kzbin.info/www/bejne/mHWao4SYo7iVm80 kzbin.info/www/bejne/ppuln3mQfMumoKs

[@MrDucnb]

Can you give me list and measure? Thanks

[@Kendin-Yap]

Materials and links are in the description below the video. Press the arrow symbol on the right below the video. (For mobile) Click the "More Information" link below the video. (For PC)

[@user-wr5xg1py7u]

merhaba, kullandığınız alıcı nedir onun hakkında bilgi vermeniz mümkün mü?

[@Kendin-Yap]

FS2A 4CH af2a 2A Mini alıcı: s.click.aliexpress.com/e/_DEXCStt

[@mahmudmitu]

How much time it can fly in single charge

[@Kendin-Yap]

about 20-25 minutes

[@mahmudmitu]

@@Kendin-Yap in your video it showed only 3 to 4 minutes

[@Kendin-Yap]

@@mahmudmitu Of course, the flight scene lasting twenty-five minutes would be very boring. Then no one might want to watch the video..:)

[@mahmudmitu]

@@Kendin-Yap I will be not bored if you send me that video link

[@omrsgr31]

6 kanallı kumanda olurmu(flysky)

[@Kendin-Yap]

3 kanal ve üstü tüm uçak kumandaları olur

[@CoolestDuckAround]

How do I land this plane?

[@CoolestDuckAround]

Hm

[@ArielBaravalle]

the ESC and servo not work with less to 4v.

[@Kendin-Yap]

it works. The receiver and servos I use work over 3.7V

[@oswelbaltodano6439]

Hl algo en la electronica que no entiendo lo podes aser con un 30 A el esc una sola bateria podes

[@Kendin-Yap]

6A is enough but 20A or 30A esc is cheaper.

[@DENE-OGREN]

Merhaba öğrencilerin kullanabileceği en basit RC model uçak hangisini yapmamızı tavsiye edersiniz

[@Kendin-Yap]

kzbin.info/www/bejne/eHzRqZ53nKeana8si=Cu0uJGoCekYlQ_HC .. sanırım bu daha kolay ve düşük maliyetli bir model olur.

[@DENE-OGREN]

@@Kendin-Yap maliyeti önemli değil önemli olan stabil uçması, çok ince ayar gerektirmeyecek bir uçak olacak 3s pil kumanda diğer her malzemeler var

[@DENE-OGREN]

@@Kendin-Yap çok teşekkürler hocam

[@Kendin-Yap]

Her uçakta ayarlar aşağı yukarı aynıdır. önceki linkteki model olur veya kanalımdaki üstten kanatlı trainer (eğitim) modellerinden herhangi biri olabilir.@@DENE-OGREN

[@DENE-OGREN]

@@Kendin-Yap tamam çok teşekkürler dediğiniz modelden başlayalım insallah çok sağolun

[@fatbubba2097]

I can't figure out why none of my rc planes fly. They are all light (made of foam board about 350g with batt), have a 700g of thrust motor (8060 prop), have large control surfaces and wing spans, yet they all take off, fly about 8-12 mph and have no control (rolling or vertical). I can even see the control surfaces working well with my controller during a "flight." Any ideas?????

[@gamerzempire2573]

CG

[@fatbubba2097]

@@gamerzempire2573 I have tried moving the CG all over the wing, and it will ether go 90 degrees or it will fly straight and quickly dart to one side with no control.

[@priyanshusahani5673]

Bhai Thora aur chep plane

[@spacelovers472]

Motorun itiş kuvveti ne kadar ? Aslında asıl sorum ağırlıktan fazla itiş kuvvetine gerek var mı ? Ben aynısının gövde konusunda biraz değişiğini mikro fırçasız motor, 3S 1050 mAh LiPo konfigrasyonlusunu yapmayı planlıyorum. Ağırlık 300 gram, thrust da 250 gram, yeter mi sizce ?

[@Kendin-Yap]

İtiş kuvveti ihtiyacı uçağın genel yapısına bağlıdır. Her uçakta aynı mantık geçerli olmaz. Benim kullandığım motorun 7.4V ile itiş kuvveti 180-190 gr. Ama tek pil yani 3.7V ile ile itiş kuvveti 100gr ın altında. Fakat Uçağın kanat yapısı, ince gövde yapısı vs ile bu192gr lık modeli uçurabiliyor. Yaptığınız modelin ağırlığı 300gr olduğu için kesinlikle kanadın altını düz bir şekilde köpük ile kaplayın yoksa havada katlanacaktır. Benim yaptığım kanat yapısı çok hafif modeller için uygundur.