I should have pointed out that I’m using only BARREL bushings for the rear truck, no cone bushings. I mean you can see they’re barrels but for anyone new to this stuff.
@michaelwagner64102 ай бұрын
Is that independent bushing the same high rebound type as the venom? And with riptide there's the krank and the APS. So is that independent bushing their high rebound one(like APS or shr) or is it the regular formula like krank or hpf? Even though the two bushing formulas are so different with performance everyone is really quick to swap them out with each other and recommend them, some people tell me krank is better for downholl others say APS. (I go to downhillers for stability advice, only problem is people don't use DKP downhill) What do you say? Should I also go .5 inch(street) bushing for roadside to make it easier to fit with cup washers? Isn't that what Tynee did anyway?
@tommynguyen86203 жыл бұрын
150lb, Riptide 87A/84A bushings here. It's a really carvy setup that has a healthy amount of rebound for me. Takes a bit of getting used to riding but it's pretty stable and handles nicely in my opinion. Rear truck 1st Boardside - 1/2 height 95A bushing + Aluminum Spacer 2nd boardside - 87A barrel bushing 1st roadside - 87A barrel bushing 2nd roadside - 84A barrel bushing Front truck 1st Boardside - 1/2 height 95A bushing + Aluminum Spacer 2nd boardside - 87A barrel bushing 1st roadside - 87A barrel bushing 2nd roadside - 84A barrel bushing
@bournechupacabra3 жыл бұрын
Can't wait for the Zeus and hurricane reviews
@ZEROBYTES3 жыл бұрын
samee!
@robertgodette46783 жыл бұрын
I get my Zeus Friday!!! I can't wait
@bartekkawalkowski27603 жыл бұрын
@@robertgodette4678 mine got delivered today
@ZEROBYTES3 жыл бұрын
@@robertgodette4678 niceee, enjoy it mate!
@kenspencer67632 жыл бұрын
Just snagged the last 97A off Amazon at the moment. Stoked for the Hurricane but should be getting it like halfway through winter so got plenty of time to tinker, thanks for the advice!
@spyplane83 жыл бұрын
Can't wait for the Flash review!!
@au18ert3 жыл бұрын
I did the same thing to my RX3 when I saw your last bushings video with different front to back. The cup washers make a massive difference and I don't understand why they are fitted as standard. The RX3 curves sweetly and is super stable right up to its max speed. It only gets sketchy going downhill beyond its max speed without power. I only wish I'd have waited for the Propel Endeavour because the RX3 is a great commuter board, quiet and almost no maintenance it just doesn't excite enough. Calling them all terrain is a push, there more street boards than street boards especially in the UK. There's not enough perfect tarmac here for anything less than a big wheel. ✌️
@user-pm2yq3wm9w3 жыл бұрын
Ive put cnc washers from exway + venom plug 95a/93a double barrel combo on atlas. The plugs are made for caliber, but if you cut them a bit they fit. Feels pretty stable
@henrismith74722 жыл бұрын
Please recommend something for a 120kg rider. Durometers etc.
@storm47102 жыл бұрын
im 122kg boardside 97a venom eliminators(plan to change these to 95A to give me a little better slow speed turning, when my buddy gets them in stock) wheelside 93a Venom Eliminators It might be to stiff for you but that is my setup
@adrianrivera8425 Жыл бұрын
I need some help I put lock tire on the screws for the motor mount and they leaked into the motor and now is squeaky and tough to move. Can I just apply acetone or will this cause more damage and the screw to take the motor apart slips so ehh
@R.u.x.xАй бұрын
What's the point of locking out the back? Why not just use different trucks that are more stable to begin with instead?
@garrettaspinwall9122 жыл бұрын
I’ve got a B-one Hercules and I was looking for pivot cups but I’m not sure what size. Also with the bushing “spacer” what would you recommend for a 110kg rider? The stock setting felt decent but I’m commuting and am looking for stability, I’m a newbie so any help is appreciated.
@albertolopezdelgado63472 жыл бұрын
I'm 66 kg i just buy the meepo hurricane which bushings do you recommend me
@jonnybryant51893 жыл бұрын
Preciate this video because I can't go over 22mph on my boundmotor flash without wobbles
@in-vision6522 жыл бұрын
How is it now and what did you settle with?
@jonnybryant51892 жыл бұрын
@@in-vision652 I've completely changed the board since then. Switched to bigger motors, Boardnamics gear drives and trucks
@wolfkoolaid7222 жыл бұрын
I'm 140-145 pounds. My set up was from back board side to front road side : 87 purple venom eliminator/ 87 riptide white short street barrel / 87 venom purple barrel/ 87 riptide white short street barrel/ 87 venom purple barrel/84 red short street barrel /85 venom yellow barrel/ 84 red short street barrel. cup washers on all board sides and back road sides. Sleeved washer worked on first front king pin but had to use a flat washer for second king pin because it made a loud clicking noise.
@bournechupacabra3 жыл бұрын
Where do we get the washers?
@DanielKwanExtras3 жыл бұрын
Good question…I’m not really sure. Riptide, Muirskate, and other skate shops should at least have the common cup and flat washers. For the tighter cup washers you might have to ask them.
@quentinquentin87933 жыл бұрын
And do you like the dkp bushing Riptide kit ?
@Ian13293 жыл бұрын
Not for me but I'm 200 lbs so probably on the heavy side I guess
@DanielKwanExtras3 жыл бұрын
Never tried them but probably good. Bit of an expensive solution.
@highestvirtue18922 жыл бұрын
How fast can you go with this set n carve?
@khaliltheking3 жыл бұрын
So when are you gonna review this boundmotor flash 2.0. ? Is it me or you usually avoid VESC boards?
@DanielKwanExtras3 жыл бұрын
There are 3 vesc boards in queue…
@douma03 жыл бұрын
How do you like the flash. Just received mine today fell twice the thing is such a beast and way too wobbly. Where do you buy these bushings from?
@DanielKwanExtras3 жыл бұрын
You can buy from Amazon or skate shops. See links in description.
@douma03 жыл бұрын
Thanks. How Do you like the flash?
@camomaster63163 жыл бұрын
Is that the zeus?🧐
@robertgodette46783 жыл бұрын
The Zeus has traditional trucks not reverse or double
@Ian13293 жыл бұрын
I'm 200 lbs dude I had to get 100a bushings LOL
@rango_unchained3 жыл бұрын
I'm a big old fat guy, over 300lbs, and new to electric skateboards. I want to get the Meepo Hurricane, but I'm not sure if I should be concerned with the stock bushings on that board?
@DanielKwanExtras3 жыл бұрын
My guess is you’d want to change them but you can of course try the stock bushings first and get aftermarket ones later if needed.
@rango_unchained3 жыл бұрын
@@DanielKwanExtras Okay, thank you.
@storm47102 жыл бұрын
Im 270lbs/122kg boardside 97a venom eliminators(plan to change these to 95A to give me a little better slow speed turning, when my buddy gets them in stock) wheelside 93a Venom Eliminators That is my setup(it's a good starting point)
@61193alexis3 жыл бұрын
Do barrel bushings even fit the Black carve 2?
@DanielKwanExtras3 жыл бұрын
Except for Exway and Metroboard, all the other eskate DKP trucks are basically the same with minor cosmetic differences.
@250rRida3 жыл бұрын
So tighten it up so much you basically creat a single kingpin truck. This is why double kingpins should not be on Eboards
@Ian13293 жыл бұрын
Agreed *sigh*
@tommynguyen86203 жыл бұрын
You don't *have* to do this to DKP trucks to get a stable setup. If you're okay with getting used to DKP trucks you can absolutely run a really soft carvy setup. I'm on 87/84 at 150lbs and its perfectly stable for me.
@TheAETHER223 жыл бұрын
Yeah true but taller trucks eliminate wheel bite
@DanielKwanExtras3 жыл бұрын
For boards that advertise speed and power (nearly every eboard), I agree
@DanielKwanExtras3 жыл бұрын
@@TheAETHER22 risers too
@DarkBloodyFoxy3 жыл бұрын
Is it BoundMotor Flash?
@DanielKwanExtras3 жыл бұрын
Yes
@DarkBloodyFoxy3 жыл бұрын
@@DanielKwanExtras Nice BTW 96/93 DKP combo from Riptide: it’s very stable but don’t turn well. But hey, I got 60+ kmph easily without any fear downhill
@lalalala39682 жыл бұрын
@@DarkBloodyFoxy WTF is KMPH ? lmfao
@michaelmercer80542 жыл бұрын
Cool
@mike2129163 жыл бұрын
answer: buy riptide bushings
@chrysr77739 ай бұрын
Double kingpin truck are a crap design and don't belong on any esk8. Your remedy is to nullify the bottom half of the truck, why not just remove the offending piece and run the truck without the bottom half? Better yet, get a set of trucks that work right.