Hi @impala1977. We are glad you found it useful. Thanks for watching!
@jasonaldrich326 Жыл бұрын
Would be nice if they showed the sign on the meter...
@IWasNoah11 ай бұрын
pretty self explanatory
@IWasNoah11 ай бұрын
if you don’t know according to the IEC / ASNZS3000 it must be tested at twice rated voltage
@davidrosas227710 ай бұрын
True… so far all the cables we’ve megg have tested at 660 M ohms in all our cables we have tested / installed here at my plant, which is what it shows on the megger she’s using in the demonstration, but like they said 20 M is a pass.
@recithree14 күн бұрын
How about verifying that the other end of wire doesn't have conductors touching.
@chchandrasekhar39129 ай бұрын
What is the test voltage
@JuanMartinez-mf5bm Жыл бұрын
You missing make test between red circuits cables or don’t apply this tests?
@reymondrono982 Жыл бұрын
All Wires minimum passing 20 mega Om's ?
@shamsadeenmohamed5074 Жыл бұрын
Thanks alot..would you mind attaching a drawing for testing wirring
@BARTECglobal Жыл бұрын
Hi! Thank you for watching. Please use the following link to download our design guide: www.bartec.de/en/downloads/heating-technology/engineering-tools/design_guide_iecex_final.pdf In page 36 you will find the "Tests and Commissioning" section. We hope this helps!
@ryanrahmat5980 Жыл бұрын
where do I put the red and black wires for testing a cable that does not have a ground braid?
@BARTECglobal Жыл бұрын
Hi @ryanrahmat5980! If the cable does not have a ground braid, then one of the cable conductors might be the grounding conductor. For example, a three-wire cords contain two current-carrying (Hot & Neutral) conductors and a grounding conductor. Check the cable type and please note, for single conductor non-shielded cables, insulation resistance testing cannot be performed because low voltage single conductors do not have a grounding conductor, shield or ground plane. Hope this helps and thank you for watching!
@___Q-bot7 ай бұрын
does anyone know what is the kind of the reel of red cable? is it for electricity or signals?
@arisan4567 Жыл бұрын
It's better if you show the results of your testing in the video
@BARTECglobal Жыл бұрын
Hi @arisan4567 You are right! We are taking notes for future videos. Thank you for watching and for sharing your feedback.
@jasonparkinson7621 Жыл бұрын
👍👍
@BARTECglobal Жыл бұрын
👍🏽
@markgil9249 Жыл бұрын
Doesn't mention what this test is for? We know but you have to mention this of you're explaining it.
@IAmThe_RA11 ай бұрын
To find out whether wires have the expected resistance value. Insufficient resistance means the wire insulation is bad and needs to be ditched as there risk of a ground fault or short circuit which can start a fire.
@Aquariun9iteMMareАй бұрын
Let me guess... you're asking for a friend?
@moristaneo9447 Жыл бұрын
you need to inject test also line to line and line1 to ground and line2 to gound. not only direct line1,2 to ground. need to separate
@BARTECglobal Жыл бұрын
Hi! Thank you for watching the video. Most Meg sheets list L1-G, L2-G, but if they pass together they’ll pass separately.
@IAmThe_RA11 ай бұрын
@@BARTECglobalwhat is her IG?
@bennyb6071 Жыл бұрын
interesting, didnt know you can megger semi conductors
@shahbazsindhu6616 Жыл бұрын
No it's was wrong because you are missing something. After testing must discharge cable...
@ibnuabassmohammed84745 ай бұрын
Please you are too fast We are learning from it Next video slowly and let's see the values recorded too
@essabhuyian2296 Жыл бұрын
ও লেডি বিউটিফুল ই ন্স টাক টার
@MarkoKastellonАй бұрын
Women test 😊
@tfun10110 ай бұрын
I’m sorry I don’t agree…we had 2 raychem techs come out to our site and Megger all of our heat trace. I worked with them for 3 days megging countless heat trace. I was told the minimum is 1 Giga Ohm of resistance “phase” to ground. They said specifically anything below 60 Mohms requires a level 2 diagnostic which is going out into the field and opening boxes to look for the problem. 20 ohms to them is a huge problem. With all do respect..what the f*ck are you talking about.
@joshuaboehler10 ай бұрын
She said 20mega Ohm's not 20 ohm's. 20 ohm's is basically a dead short.
@tfun1019 ай бұрын
@@joshuaboehler20 mohms, 20 ohms it doesn’t matter my guy. Read what I said.
@champ86056 ай бұрын
Depends on the voltage used for testing. They most likely tested upwards of 5kv whilst this test was under 500v. You're clearly not an electrician and dont know what you're talking about.
@tfun1016 ай бұрын
@@champ8605 Most likely tested upwards of 5kv? 🤣. You’re sooo clueless bro..
@garza13676 ай бұрын
You were also told, face mask and vaccines would help stop/spread covid from “qualified” people… moral of the story, not every “professional” gives the right info
@acefuellas21379 ай бұрын
why 550 meg is always the reading of a good insulation
@ducatininja3866 Жыл бұрын
Ive recently run 140mts of heat trace. I did a test and getting more than 20 megaohms. However when the heat trace is turned on its drawing 54amps. Any suggestions?