For those of you that don’t know big block started in 2000!......really dude........actually people it was 1997 when the first 700 twin big block came out for Polaris
@dirtyfacegeorge99385 жыл бұрын
96 had a 600 twin, rare. I assume it was a big block too.
@joelaichner30258 ай бұрын
Snow checked my 1998 XC 700 , got the good jugs , that was a mystery surprise ,
@joelaichner30258 ай бұрын
2005 RMK SLP performance edition motor , bored carbs , and the whole SLP catalog, in a 2004 switchback , complete restoration , ridiculous money ! Plus the motor is at SLP right now , ate a power valve last year , 1 inch in under 30 seconds , if I’d just have ridden the old XLT for a few more years , I could have paid cash today , for a VR1 turbo , but I like my old ride. The Snow Missle , see you in the twisties & trees , Ride the Upper Peninsula of Michigan ! We’re Friendly
@davidhaley70534 жыл бұрын
Very good video. Thanks
@breezy20924 жыл бұрын
My pto crank bearing went after 3700 miles on my 2001 rmk 700 , first time anything went on it besides voltage regulator and my low beam bulb
@thatmodshop71608 ай бұрын
Polaris Big Blocks started in 1997 and only in 1997 with big purple rectangle/square head 700, they then went to the red head round design 700 600 and 800. 1997-2001 were non ves 2002-2005 was when ves came to the twins and the 600 ves was a short block.
@edwardabrahamiii37424 жыл бұрын
Do the 14 indy liberty 800s have the wide bearings in em the good 1s?? Its the pro chassis
@devinsegin52285 жыл бұрын
Are the middle bearings supost to be harder to turn on a pro rmk 600 2016?
@dwanebernier3142 жыл бұрын
I have a 2013 switchback assault 800 and am upgrading crank bearings and seals. Is there an all inclusive kit or, are all bearings/seals purchased separately? One of your videos talks about o-rings on the inner bearings to prevent them from spinning in the case? Thanks for your time! Dwane B.
@deanthompson89204 жыл бұрын
I have had to Polaris 800 big bearings go out.. on a 2011 and a 2013 first one with fifteen hundred miles second one with 2400.. why?
@troypaulson91523 жыл бұрын
I have a 2004 artic cat 900 mountain cat. How much would you charge to rebuild the crank with new bearing?
@prestonjames81804 жыл бұрын
I got a 2011 rmk 700 in need of a motor. Is a 600 ho block the same? Just different jugs and stuff?
@kyle.carmichael58563 жыл бұрын
I dont know if u will see this but can I change the conecting rod or what do I have to do the bearings bad
@whatsup73422 жыл бұрын
Can you guys rebuild 97 seadoo 787 cranks?
@joelaichner30258 ай бұрын
P.S. BYOB ! Lots of it !
@2strokeadventures4 жыл бұрын
Do u have a video installing the crank in a stock 12 pro rmk 800 case?
@2strokeadventures4 жыл бұрын
@@rockymountainchainsaw I just pulled the motor and took the crank out... Getting ready to re assemble. Getting a service manual for this sled on Tuesday and going to finish er up this month. Im good at reading and following instructions but visuals help alot. Was able to replce my clutch with nothing but KZbin videos, so ive been looking for some bottom end vids. Lots of top end vids but nothing on bottom end. Thanks for responding quickly.
@colbylawrie66086 жыл бұрын
What the company that I can buy my parts from, or company I can send my crank to???
@colbylawrie66086 жыл бұрын
Okay,thanks
@Rickydbaby3 жыл бұрын
what type of bearing puller do you use to pull the PTO bearing off? something similar to this? www.harborfreight.com/bearing-separator-and-puller-set-62593.html
@brianmosurak87753 жыл бұрын
I need help 2000 to 800 X
@beemerkon3 жыл бұрын
thousands of miles in the back country thats way out in the back
@jehleiter1 Жыл бұрын
North Pole
@brianmosurak87753 жыл бұрын
2002 800 x
@brianmosurak87753 жыл бұрын
Could you possibly get ahold of me I need to have you rebuild a Creek shaft for 800 X 2200