How to program your Blendtec blender | Connoissuer 825 / SpaceSaver 825

[@heartbeatforyouali]

Hello , I am having a motor overload error in my blendtech 825. Any chance you can explain how to fix it ? Thank you

[@carlybruckner1554]

Thanks for your help!

[@theblendtecspecialist7002]

You're very welcome Carly

[@nachovanbuuren]

Hola, como puedo quitar el error Overlord?

[@jelimart]

Great video!👍 How do I transfer custom cycles to the older 5-pin version?🤔

[@theblendtecspecialist7002]

Hi Jesper, thanks for the comment and glad you found this useful! That’s a really good question that unfortunately has a complicated answer. If you are making your own custom blend cycles using the blend wizard and a USB stick then it is not possible to simply transfer these same settings to a 5-pin port. Furthermore, I think the software and hardware support for custom programming the 5-pin version is now obsolete. The old way of custom programming involved using some Blendtec software and having your blender connected to your PC via a 5 pin programmer - it was cumbersome and sometimes tricky. These days, things are much easier and quicker simply using a USB stick. My suggestion for your 5-pin machine(s) would be that you use the pre-programmed settings and get as close as possible to what you need (Q-Series, ABS, Smoother) and I have a video on how to do that here: kzbin.info/www/bejne/rn_HoZyFjqpsptE If you really, really want to get your old machine set up with your custom programming, I can help you with that but the hardware will be expensive as it’s hard to get hold of these days. All the best Adam

[@dmounce5513]

Bpught of these used. Where can i find the blend profile chart you showed in the video. Thanks

[@sewhoppy]

I have the big train model and lost my manual 😢

[@paulobatista3434]

Hi just bought a second hand Blendtec connoisseur 825 But doesn’t have a USB port or 5 pins entry Also I can’t get to menu Every time I press and hold 2 and 4 buttons just start work Looking forward for your help Thank you Paulo

[@theblendtecspecialist7002]

Hi Paulo, Thanks for the comment, I really appreciate it. If you don't have a USB port or a 5pin port, then I'm not sure what model it is as it should have one or the other. Is it possible that you've purchased a domestic model such as the Pro 750 which looks very similar? You could try following this guide which is for previous models of the Connoisseur called the Q-series. kzbin.info/www/bejne/rn_HoZyFjqpsptE Either way, let me know how you get on. All the best and thanks again Adam

[@beardfais]

Main menu doesn't come up with button 2 and 4. I have the blend tec connoisseur 825... When I hold both buttons down it just starts a cycle.

[@theblendtecspecialist7002]

Check the underside of your blender motor. Do you have a USB slot or a 5-pin port. If you have a 5-pin port then check this video instead kzbin.info/www/bejne/rn_HoZyFjqpsptE Thanks and good luck

[@felipedecarvalho5827]

Do you have a decibel scale for each model with and without a hood?

[@boomer7862]

My blendtec has a problem With The rotor, can you help me please? The model is es3

[@theblendtecspecialist7002]

Hi Boomer, where are you based? ES3 is a family of blenders - is yours a commercial machine such as an EZ600?

[@boomer7862]

@@theblendtecspecialist7002 yes

[@theblendtecspecialist7002]

@@boomer7862 If you are in the UK, you can call the UK repair agents on 0117 9533 522. Outside of that, you will need to contact the local repair agent for your country. If you can tell me where you are, i can find that for you if you like :) Thanks

[@kennethjessie1282]

get to it you talk too much about non necessary information