3M double sided mounting tape would help the tank and also yellow ptfe tape for the petcock. White is probably ok though
@AgelessNomad9 жыл бұрын
thumbs up btw.
@007tallguy3 ай бұрын
Rather than 3m, I'm going to use double sided Gorilla tape on mine. 👍
@joshchelvolski10336 жыл бұрын
What is the highest amount of litters of a gas tank I can buy and what website i buy it from, can you leave it in comments because I would like to upgrade my tank ?
@mikeshobbiesandrandomstuff4 жыл бұрын
A motorcycle gas tank holds three gallons for average tank size.
@flyingsky15594 жыл бұрын
I think you can find up to 4-5 liters
@joshchelvolski10334 жыл бұрын
Thanks you much for everyones comments, i managed to upgrade my tank to 3.5 litter tank. Sadly i bent the crank shaft while having the cluch engaged. Though i got a new replacement engine from bike berry.com , i don't think i will be using it anytime soon since i got myself a 2016 kia soul and a motor cycle.
@jimpruett40057 жыл бұрын
my fuel cap leaks, have you got a fix for that
@randomguywhostoleallofyour884 жыл бұрын
Did you find a fix? I got the same issue. Please help
@jacobschepis64073 жыл бұрын
Mine also i thought it was just vented for easy gas flow
@Westhelockpicker2 жыл бұрын
do your gas caps have the rubber seal?
@martinayala50732 жыл бұрын
do you recomnd putting any tape or rubber between the frame and tank?
@HughesMotorized2 жыл бұрын
Sure. It will help some in keeping the tank from moving
@adamdorris40816 жыл бұрын
I fabed double 1/8 plate steel 2 pieces, 3 ×6 welded them to the frame and laid some cushiony rubber down. Drilled the stud holes out and cut the excess off. I've tried all sorts of ways with 3 tanks and they all cracked at the welds eventually after a couple hundred miles from viberation with this guys method. Just sayin.
@oct1919946 жыл бұрын
Why did you not use the petcock filter and the inline filter together
@HughesMotorized6 жыл бұрын
A good inline filter works for me.
@theone2be336 жыл бұрын
redboioh9 of course you can and SHOULD. Dont listen to this guy. Remember this is KZbin where EVERYONE has an "OPINION"
@deadskinnation14114 жыл бұрын
@@theone2be33 exactly
@entertainmentforyou66777 жыл бұрын
thank you Alot of videos were very helpful for the past week I've been installing the flying horse 80cc and have ran into some issues on my Huffy 18 speed Nigeria mountain bike! the muffler hits the pedal just enough to not pedal so I have to bend it! plus the clutch cable and throttle cable is to long would it still work ok in your opinion? Thank you
@gregdenman2342 Жыл бұрын
Plumbers strapping is what I used to mount my tank, that flops around a lot...big tube 18 speed mountain bike
@jaycee2366 Жыл бұрын
Alot of bikes actually have the cables on the top of the frame. Those need rubbers because they will eventully vibrate through bottom of the tank.
@jkoeberlein19 жыл бұрын
Not bad but what we do is to use 4 sheet metal brackets. Facing each other with the compression force clamping the top tube. The tank stands on the studs and we've never had a leak.
@jamesmcgarity43307 жыл бұрын
John Koeberlein Mini bike gas tanks for sale
@jamesmcgarity43307 жыл бұрын
Mini bike gas tanks for sale.
@jamesmcgarity43307 жыл бұрын
John Koeberlein search mini bike gas tanks for sale
@mikesbarn18582 жыл бұрын
I Install the original upside down on the tank with stand off nuts then I put electrical brackets on the underside. Now all the stress is on the stud threads not the welds
@eugenegriess18963 жыл бұрын
He keeps preaching about tearing up the tank bolting it on. Why not double nut it and you won't have that problem.
@BobTheBuilder2944 жыл бұрын
The instructions mine came with were awful and didn't even mention the existence of the fuel filter. Most videos don't either.
@scaredofghosts68132 жыл бұрын
I have a curved tube😭 ..at this point ima find a baby to hand tighten my studs
@Ken19700 Жыл бұрын
The Teflon tape needs to be rated for gasoline. It should be yellow.
@infohere10005 ай бұрын
how do i order the larger plates for the 3liter gas tank online
@deanjohnston38306 жыл бұрын
Great informative video, my question is how can I use that same tank with a 2stoke weedeater style carb, which currently requires a return line?
@theone2be336 жыл бұрын
Dean Johnston drill a hole into the top of your tank for your return line. Make sure to seal it up with silicone. Should be fine.
@gregdenman2342 Жыл бұрын
I have the problem with the shifter cables running along the top of the frame, so the tank likes to flop around a lot. Anybody have a fix?? Please contact me via email.Thnaks
@HughesMotorized Жыл бұрын
Fabricate a clamp with openings for the cables that attaches to tank mount bolts.
@Westhelockpicker2 жыл бұрын
I like the new ones they thread on the outside
@JoeDemons3 жыл бұрын
Hey I got a leak.....it looks like it's coming from the petcock and I don't have a washer there where could I buy a small red washer and what's the diameter for it?
@HughesMotorized3 жыл бұрын
Teflon tape
@SantisValiant4 жыл бұрын
How can I mount the tank onto a top tube that's about 3 inches in diameter?
@HughesMotorized4 жыл бұрын
velcro might help
@larryshaver35687 жыл бұрын
Who sells a punch like that?
@HughesMotorized7 жыл бұрын
amzn.to/2fi6AmH
@pdogg3108 жыл бұрын
thank you this helped a lot
@audieallen97342 жыл бұрын
I think the filter in my petcock is clogged on the first tank.... what do I do!?
@HughesMotorized2 жыл бұрын
Remove it. Toss filter in trash and use inline filter
@c.rutherford Жыл бұрын
It seems a strange design for the kit stock tank (they all seem identical) that it tapers downward in the back when they almost always slope at such a steep incline mounted on bike frames 7:00. Wouldn't it hold so much more gas, if it was mounted reversed and the cap was on the other side? Or at least if the cap was at the top. idk.
@theAussieG4 жыл бұрын
I ran a length of clear, Gorilla double sided tape along the valley of the tank. Seems to help hold it and stops it slipping side to side.
@earthenergyhex4 жыл бұрын
Do you have any tricks to keep the gas cap from leaking while riding it?
@HughesMotorized4 жыл бұрын
Never an issue. New cap might be in order
@andreleverettejr37477 жыл бұрын
I can't find a way to look up the dye I need for the powder coating, anyone know what you have to look up?
@rhetorical_annihilation5 жыл бұрын
I was wondering about the gas tank lid. It's lips are shaped like a flower and it doesn't screw on. I can't figure out how its supposed to secure and stay on while riding. Is yours like that? Please let me know if you know how to secure it. I would really appreciate it.
@williammason34535 жыл бұрын
Helped me understand what was going on. Thanks. Great start to fixing problem
@jacobsurrett59284 жыл бұрын
Good call on the Teflon tape. Mine too about a dozen wraps.
@scaredofghosts68132 жыл бұрын
What od/id is that gas line ?
@HughesMotorized2 жыл бұрын
3/16" or 5mm
@craigalbright51265 жыл бұрын
Cool thanks, that is my next project
@luisclaudio9995 Жыл бұрын
Exactly what I was looking for to solve the tank mounting issue I was having... Thanks
@HughesMotorized Жыл бұрын
Glad I could help
@melissaboam53228 жыл бұрын
is it a 1 gallon tank?
@HughesMotorized8 жыл бұрын
+Melissa Boam no 3 liter
@Kihidokid8 жыл бұрын
+HoustonMotorized if i mounted a jerry can as a gas tank down by my back wheel like a saddle bag or in a saddle bag, will it work or does the tank have to be above the engine
@HughesMotorized8 жыл бұрын
Needs to be above. Gravity feed
@entertainmentforyou66777 жыл бұрын
thank you Alot of videos were very helpful for the past week I've been installing the flying horse 80cc and have ran into some issues on my Huffy 18 speed Nigeria mountain bike! the muffler hits the pedal just enough to not pedal so I have to bend it! plus the clutch cable and throttle cable is to long would it still work ok in your opinion? Thank you
@theone2be336 жыл бұрын
Entertainment for you cut the cables shorter for length you need.
@Amunrad5 жыл бұрын
Use the yellow teflon tape for gas.
@matthewsteva60187 жыл бұрын
is the any way to get a fuel gage gas cap
@360brokebros37 жыл бұрын
I know this is kinda old. But if I don't enough room for the gas tank. To mount it to the top does it need to be on the top tune above the engine. Or can I lit it leval with engine. Or underneath it?
@theone2be336 жыл бұрын
GBodyBoys you can put tank anywhere you want as long as it's somewhere above it. Its gravity fed
@mikesisto26554 жыл бұрын
Very helpful thank you
@joshchelvolski10336 жыл бұрын
would'nt the gasoline dissolve the teflon tape when wraping the petcock value ?
@theone2be336 жыл бұрын
Josh Chelvolski nope. The teflon tape is wrapped around and petcock is screwed over it thus creating a seal. I did it to mine and works fine. No leaks yet. Get 62 miles per tank
@miguelvelasquez15305 жыл бұрын
What size is that gas tank ??
@HughesMotorized5 жыл бұрын
about .6 gallon I think
@dawnbenoit15417 жыл бұрын
I'm building a Electric bike &want to use a tank for a motorcycle battery inside of it what size tank will I need?
@notcholibre7 жыл бұрын
Probably 3.5 liter
@theone2be336 жыл бұрын
A 20ton tank will work just fine honey
@deltabluesdavidraye6 жыл бұрын
You need rubber between motor mounts,tank and frame .
@theone2be336 жыл бұрын
David Raye just some padding is sufficient for sure. Helps with vibration and stress to tank bolts for sure.
@HughesMotorized6 жыл бұрын
Not no, but HELL NO ! Great way to break a mounting stud. Signed ... someone who has built 100's of bikes
@martinayala50732 жыл бұрын
@@HughesMotorized would you v put something between the frame and the mounting plate for the 4 stroke?
@HughesMotorized2 жыл бұрын
@@martinayala5073 No. Just make sure the mount matches the frame. You might have to file or grind some on the mount to get the best fit
@martinayala50732 жыл бұрын
@@HughesMotorized OK. Thanks for your advice
@yelstan47766 жыл бұрын
Thanks.....
@denise4646crn508 жыл бұрын
HOW FAR CAN ONE GO ON A TAKE OF GAS
@themonroeboys87008 жыл бұрын
if it's an 80cc it's 150 miles a gallon
@theone2be336 жыл бұрын
As far as it'll take you
@martinayala50732 жыл бұрын
About 60 miles. On that tank. Since it's half a gallon.