How To Rebuild Yamaha V6-V4 2 Stroke Carburetor.

  Рет қаралды 22,571

DSM Enterprises

DSM Enterprises

Күн бұрын

Пікірлер: 25
@Raman382cig
@Raman382cig 2 жыл бұрын
The 130 beto looks like the same carburetor. U know how there must must place the screw for perfekt engine run?
@martinkoche4375
@martinkoche4375 5 ай бұрын
Thank you
@carlospadilla9576
@carlospadilla9576 Жыл бұрын
The little plate either the gasket. There are two air jets is there a way you put them in
@bimmerwman
@bimmerwman 6 ай бұрын
Do you know if the screws are JIS or regular Phillips head? Thanks for the Video!!
@alexwallace8573
@alexwallace8573 9 ай бұрын
What is the factory idle mixture setting for a 1992 txrq 200?
@tyyoung3698
@tyyoung3698 Жыл бұрын
Wow, what a great video. Thank you. My confidence is soaring at this point. I feel like the investment in a small ultrasonic parts cleaner is worth it -- right ?
@dsmenterprises6699
@dsmenterprises6699 Жыл бұрын
It will help but a good cleaning solution with compressed air due the job most of the time.
@jaymarek1795
@jaymarek1795 16 күн бұрын
I have a 93 p150 precision blend motor. Any pointers on cleaning those carbs?
@dsmenterprises6699
@dsmenterprises6699 16 күн бұрын
@@jaymarek1795 They should be similar to the carb in the video My main bit of advice is to take your time and check every passage for blockage take pictures as you take them apart and notes on the settings. Number the carbs and fuel bowls keep all the hardware and jets set aside according to the carburetor it came from
@jaymarek1795
@jaymarek1795 16 күн бұрын
@dsmenterprises6699 thanks
@dsmenterprises6699
@dsmenterprises6699 8 ай бұрын
I check all the mixture adjustments screws if I did not have a manufacturer spec on them but it is not the gospel sometimes as the motors age and our fuel changes so will the tuning of the carburetor. As for the measurements on the float I have been doing this since 1990 and have never really seen a benefit of going that extreme on the float measurements I like to get them so that the bowel is full of fuel
@Fpvcandy
@Fpvcandy 8 ай бұрын
Man this is my main question that no one is ever %1000 clear on... On this model carb how many fuel mix screws need to be counted per revolution as they are taken out? Only 1 correct? Per carb? I usually put a digital caliper on the floats before removing them to get an exact reading on the measurement they sit at so I can match it when I put the bulb back in. Would you consider this good practice or waste of time?
@andrewjernigan799
@andrewjernigan799 Жыл бұрын
Hey I have a late 80s Yamaha pro v 150 2 stroke I just replaced both fuel pumps after I replaced them it seems to be running super rich is there a way to lean is out so it won’t be smoking as much before I replaced the pumps it was barely smoking only when first started any ideas
@dsmenterprises6699
@dsmenterprises6699 Жыл бұрын
Check your oil pump rod when the throttle is set adjust the oil rod until it is close to the sop pin
@diveandrelaxlanta
@diveandrelaxlanta 2 жыл бұрын
Can you let us know what you used in the ultrasonic cleaner?
@dsmenterprises6699
@dsmenterprises6699 2 жыл бұрын
Yes 2 parts distilled water and one part simple green. I use the lemon scent. On a side note my machine holds about 3 gallons and I will also put a small amount of dawn dish soap in the water, Never leave carburetors in the ultrasonic machine for more than 15 min it can damage the finish on the carburetor so keep an eye on them as you go.
@OGAstra
@OGAstra 2 жыл бұрын
whats the best place to order genuine yamaha carb kits and impeller kit? yamaha 175hp 2 stroker
@dsmenterprises6699
@dsmenterprises6699 2 жыл бұрын
Partsvu
@timtiffany4302
@timtiffany4302 Жыл бұрын
How do you ajust the carbs..my 200
@dsmenterprises6699
@dsmenterprises6699 Жыл бұрын
What model and year
@abdulla9869
@abdulla9869 2 жыл бұрын
Hi how are you
@georgenettlesjr1466
@georgenettlesjr1466 2 жыл бұрын
How to mail you mine?
@dsmenterprises6699
@dsmenterprises6699 2 жыл бұрын
I can do that but would suggest you try and look for someone local to you that is qualified. And I am booked until July 12
@alexebis9237
@alexebis9237 2 жыл бұрын
Hi
@blessingD-dy7fo
@blessingD-dy7fo Жыл бұрын
I need a job I'm yamaha expert
Rebuilding a Yamaha Outboard Carburetor
47:27
Michael Romer
Рет қаралды 35 М.
Мясо вегана? 🧐 @Whatthefshow
01:01
История одного вокалиста
Рет қаралды 7 МЛН
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН
CLEAN IT!! Yamaha 115 Outboard carburetor maintenance 1 of 3
12:01
CoastalCruiser
Рет қаралды 35 М.
How To Clean Evinrude 75HP Carburetors (3 CYL 2 STROKE)
31:17
buschfishin
Рет қаралды 71 М.
The BEST Way To Fine Tune Idle Mixture Screws For Your Carburetor
15:16
TheMotorcycleMD
Рет қаралды 1,9 МЛН
Yamaha 130hp 2 stroke verses 130hp four stroke
8:52
ShortFlic
Рет қаралды 189 М.
Four stroke carburettor synchronisation
29:45
Dangar Marine
Рет қаралды 880 М.
Basic Mikuni Keihin Slide Carb Tuning ✔
14:09
Mark Young - Outside The Box
Рет қаралды 560 М.
DIY Overhaul and adjustment Power Head Yamaha Outboard 2 stroke V4 V6
38:41
Yamaha 150 outboard 2 stroke carb rebuild
11:42
Chris Peters DIY
Рет қаралды 25 М.