This would have been a useful video if you didn't have Steven Hawking narrate it. It was too annoying to watch.
@SparkedEd13 жыл бұрын
@bassabigdeal what? entertainment and education? Sorry, you dont have to watch if you dont want. The Goal of my vids is to give something different than all of the other bland car audio vids out there, and to spread the years of knowledge and experience I have attained from doing this. If you already know so much and make the best vids, or have seen the best vids, you need not share in my channel if you do not wish. Thank you for watching this vid and good luck to you in the future.
@SparkedEd11 жыл бұрын
Surround to cone is a tough joint and may never be back to 100%. But you can use "Amazing GOOP" or epoxy to fix that joint. Just make sure it is something that can adhere or bond to rubber.
@SparkedEd12 жыл бұрын
@Qaasim830 There are many different factors, coil inner and outer diameter and coil height, also spider sizes and clearances. You need a recone that is made for your woofer. Try fixmyspeaker . com
@SparkedEd13 жыл бұрын
@bassabigdeal lol, OK. Well you are free to watch and learn a few things, watch more of my vids and learn about what it is I do, but your immature, and ill informed remarks are not welcome here.
@SparkedEd12 жыл бұрын
lol. well you can use adhesive dissolver but it doesnt really work on silicon. The silicon shouldnt have soaked through the fiberglass/woof so it should eventually separate from the box.
@SparkedEd13 жыл бұрын
@tacomabanga1986 Its just black CA with a slight rubberization. Bonds well to Foam type surrounds. Have to rip or cut the surround to get it off. I never used any CA that sets up white.
@tyoung31913 жыл бұрын
I like to use GOOP on the surrounds as well as the dust cap, i apply the ca to the spider landing, then goop to surround landing, drop cone in, press firmly and spay activator on spider. Once held take the subwoooofer gasket and put it on, this holds the surround down to the GOOP great! Reason behind using GOOP on the surround is its much cheaper/ easyer and holds great! Awesome vid ed!
@SparkedEd13 жыл бұрын
@92TegRs Well I built my own recones. You can contact the manufacturer of the woofer you want to repair to purchase a recone, or try fix my speaker , com
@SparkedEd13 жыл бұрын
@tyoung319 GOOP is good there too. Just takes a while to fully dry and still costs some bit o money. Buy its available in most hardware stores.
@SparkedEd12 жыл бұрын
The voice coil pushes the cone in sequence to the electrical signal fed to it. The cone then vibrates the air molecules and this is sound.
@SparkedEd12 жыл бұрын
@warmaster5128 parts are hard to come by. I may sell some in the future but for now, fixmyspeaker . com is the place
@SparkedEd13 жыл бұрын
@Quekil830 Only ones you have the parts for. I only had a few parts laying around for this one.
@SparkedEd13 жыл бұрын
@emartinez0291 Nope, no Hifonics Woofers there. Just custom woofer parts and a T3 Audio woofer.
@SparkedEd12 жыл бұрын
@GoPre474 Maybe from Sony but I doubt they offer recones, youd have to contact them to see.
@SparkedEd13 жыл бұрын
@carloextreme I am not familiar enough with those woofers to know if parts are compatible.
@SparkedEd13 жыл бұрын
@CAneophyte Most hobby shops have basic types, or you can go to fixmyspeaker, dot, com
@SparkedEd13 жыл бұрын
@bubba906 Working on a new vid series now. Just needed my computer back and running.
@SparkedEd12 жыл бұрын
I purchased from an industrial supplier. You can try CA Plus, or even hobby shops
@J00bles13 жыл бұрын
i like the video! was a great how-to and even a veteran reconer (like myself) picked up a handy trick or two. i just wish YOU would have done the narration instead of the computer. got a little annoying lol
@theskeemask12 жыл бұрын
I've only done one re-cone so I'm no expert, got an 2002 RE XXX and when I re-coned it, as you did (except I did the whole surround at once) the surround moves all the way to the edge of the landing for the surround, which I thought was fine until I put the gasket on and it was riding on the surround as well the mounting screws would cut into the surround slightly asked Fi about this and they explained when you glue the surround down you need to put the gasket on to align the surround correctly
@tyoung31913 жыл бұрын
@ShowtimeSPL It does for sure, but i build the recone while reconing the sub now, so it sits for a day or 2 any way......... I always seem to run out of CA lol so i try and use it the least since theres no quick way for me to get more...... I guess I could stock more than 2lbs at a time huh lol :P With the glue I get from jacob (think its the same as yours) its tough to get it off the top landing vs the goop..... Word to the wise, dont get the ca fumes in your eyes BURNS = understatement :)
@Loudizzzzle13 жыл бұрын
I always love me some edwin T. Socket. Very informative video! LIKED!
@warmaster512812 жыл бұрын
@i7cpu i would do 8 ohm im not a owner of the channal but that would be safe look on the magnet of they existing subwoofer on your ampilfire and get the number and look one up and see all the inpedences and try to find a subwoofer at the ohm it is and all the inpideances correct
@SparkedEd12 жыл бұрын
The automotive or the Marine. I think they are the same anyway.
@SparkedEd12 жыл бұрын
I will soon, I am building a webstore at showtimecaraudio . net
@Cashdollar200912 жыл бұрын
Hey I bought that Diamond Audio subwoofer! Lol. Made a box out of scrap wood and managed to do a 135 @ 40Hz on around 100wrms in my tiny temp. setup in my Aveo. The direct leads were nice. :)
@SparkedEd13 жыл бұрын
@bassabigdeal Oh? And who are you and why would you say that?
@theskeemask12 жыл бұрын
You do not want to glue+accel that way when doing the surround... some subwoofers require you to put the gasket on to line up the surround properly.. just sayin'. Nice vid though!
@sikvibration13 жыл бұрын
great vid man extremely helpful i hav mojos so i just swap baskets and love the subliminal showtime spl that kept popin up
@SparkedEd12 жыл бұрын
@elijahcollins1988 you can try alpine or fixmyspeaker . com
@SparkedEd11 жыл бұрын
I make my own, watch my other vid on how to make a re-cone
@UNIQUE-eu9ik11 жыл бұрын
For your permission if I can ask you questions I'd like to you what you know I hope that don't offend yousome people just need a little help like me lol I hope you reply me with just a simple yes or no will be fine instead of no reply you know Ii have a passion for this kinda stuff and I'd like to learn more I'm honestly just asking for your help and if we could be friends so I will stop there i could write all night lol yea well bye hopefully u get this
@UNIQUE-eu9ik11 жыл бұрын
Hi I just wanna say like your video and you really inspire me a lot I fix subs for friends some times and instal systems sometimes but I feel that you are really intelligent and I read every one of your comments lol and people are just immature and I know people ask you questions all the time and its prolly annoying and I know you prolly don't reply to all of them so I just wanna say I think your very smart and I wanna just ask you if
@jamesw954611 жыл бұрын
Quick question... i have read many forums regarding fixing the surround on a subwoofer but i have a Phoenix Gold Rsdc 12" Duel 2ohm voice coils capable of 600 watt rms at 2 ohm. When playing the subwoofer noticed odd flapping noise to find out that I blew the butyl rubber surround off some of the cone about 6 inches. What would be the best steps to take to attach the rubber surround to the cone again?
@tacomabanga198613 жыл бұрын
ed, do u use a different type of ca glue because mine wouldn't glue the surround, i had to use loctite glue for it to work right, all ca glue did was set up white and come unglued and shimming makes a huge difference if u have surround problems, i had to shim mine to keep vc straight, i dont like tight vc gaps but the subs perform awesome tho lol, keep up the good work mr socket
@SparkedEd12 жыл бұрын
At full power for daily use, yes that is a bit too much.
@i7cpu12 жыл бұрын
Hi I need kind a professional help , I've got 3A andante "prelude " bi-amplified 3 way speaker but woofer has blown and I don't know which woofer to put 1. Eminence Guitar Legend 4 or 8 ohms? or this kind a woofer it's only for guitars usable freq 45 hz- 3.5 khz 400 W or 2. Martini Wiseman 51 hz to 4 khz 400 W ? help me please if you can which one should i put ?
@theloudgamer97087 жыл бұрын
Subloofer xD
@Dojahs7 жыл бұрын
TheLoudGamer 9 I just remembered this video while talking with a friend. I couldn't stop laughing the first time I saw this shit 4 years ago just cruzin youtube
@theskeemask11 жыл бұрын
You're right, sorry for tryna act like I knew something when I didn't.. two re-cone kits they put the wrong surround for my basket.. sorry dude!
@pimpinoes11 жыл бұрын
i have a 12 inch kicker cvr do you think if i grabbed a recone kit i would be able to use the basket from the cvr if i got the same size voice coil and would that change the rms in any way could i make it go up or down??? ive never reconed but i have so many blown subs lying around it wont hurt to try
@SparkedEd12 жыл бұрын
just gotta get a razor knife under there and chip away
@SparkedEd12 жыл бұрын
@sk82rap I built my own, I worked at a woofer factory
@Qaasim83012 жыл бұрын
I got a question if you guys dont mind.....I want to recone my subwoofer but the manufacture doesnot make recones so i was searching on the web and found this sing 4 ohm recone kit and my subwoofer is a single 4 ohm will this work
@bassabigdeal13 жыл бұрын
Hey man listen, If you like the computer voice keep it. You shouldn't have to compromise your video on my personal judge men
@mminc8110 жыл бұрын
@patriotpaqtrick, The glue he is using is called CA Glue and the spray is to speed up the drying of the CA Glue.
@TACTICIAN400912 жыл бұрын
Mixed emotions im having as i watched as those sub came back to life and i also feel bad because ive trashed a lot of sub's because they where blown dam.But screw it good job on the sub's and the vid.keep it up
@splaudio113 жыл бұрын
the robot voice had me loling really hard but its great to see the great ed lester and his alter ego edwin t hard at work
@matrixownz11 жыл бұрын
ed i have a question i need to glue a new foam surround to a polypropyene cone and dust cap what glue can i use the will have a strong hold contact cement says it wont work with it ? thanks
@scbjgs12 жыл бұрын
...that's only gunna take 3 years...but ok..didn't know if there were any tricks like heating olive oil and vinegar to exactly 134.7 degrees and spraying it on there or something dumb. haha
@Ian2lo4u2c13 жыл бұрын
(Standing Ovation) Ian2lo gives 2 thumbs up.... Showtime, has outdone himself.... I shall sub now.... I feel like a vid response is in order, if you'll watch it... I have something to say....
@bassabigdeal13 жыл бұрын
It's a good video dont get me wrong and it's helpful. I just don't think you really had to include all that bullshit
@GeoAl0911 жыл бұрын
Silly but serious question. Guy with the glasses I really like your hairstyle. What do you call that? Er like if you go to get your haircut, what do you say to get that style?
@357demonio12 жыл бұрын
@ShowtimeSPL hey man T3is out businnes, so i wonder if your guys have TSNS motor for sale. cuz i have 2 baskets from DC audio , I wany use w/ TSNS motor, please let me know...
@FonZ459013 жыл бұрын
@narcoti yes that is possible, then you just need to recone with a different coil. Where you have to do this depends on what subwoofer you've got. what subwoofer do you have??
@SparkedEd13 жыл бұрын
@bassabigdeal oh Thank you, its not about that. A lot of people bash on youtube, unreasonably. I look at all of us car audio guys as a select group that share a common interest and that's the groundwork for friendship. If a lot of people dont like the computer voice, I wont use it again. But a lot of people like my humor and what I add with knowledge so I keep including it. We can all share ideas for vids and audio.
@956rangoflex13 жыл бұрын
@showtimespl if I got db drive,Memphis,hifonics goliath,etc. That don't have recones where or how do I go about fixing them and psi has turned down every request I submitted
@SparkedEd12 жыл бұрын
@poweracoustik267 These are Dual voice coil subs
@warmaster512812 жыл бұрын
@ShowtimeSPL were you get the parts then just wondering i kinda want to get into this to recone and stuff
@FAMOOSE13 жыл бұрын
awesome vid ed way to go aways wondered how to do it right still dont know if i would try it but good info
@scbjgs12 жыл бұрын
i've got 3 jl audio 12's in a fiberglass box that are siliconed/colked into the box....does anyone know any way to get them out with-out destroying anything?...
@habrimable13 жыл бұрын
hey i got a eclipse sw4200 12" thats blown and i want to recone it but where can i get the kit, how much will it be, and what kind of recone kit should i buy.
@carloextreme13 жыл бұрын
hi Mr.Socket! i have a DD 2515 that is rated @ 750W RMS and im pushing it to 1000W RMS, daily. my question is, can i use a 3515 recone kit if i blew off my 2515?
@Piggie82213 жыл бұрын
I like the computer voice, but maybe some subtitles would be helpful. I wouldn't be able to recone a woofer because of how easily I get distracted by animals.
@SparkedEd12 жыл бұрын
Sounds like there may have been an issue or something custom going on. Most woofers are not like that and only use the basket to align the surround. And some surrounds have a solid landing so the holes have to be cut or punched afterwards anyway. Some are tooled with the holes already punched and that would require spinning the cone/surround until they are lined up.
@scbjgs12 жыл бұрын
seperate from the box by itself?...it's been in there for like 7 years.. :/. and i used adhesive colk. haha. gunna have a fun day doing this..
@teamfapa13 жыл бұрын
@ShowtimeSPL where can you buy the black ca glue all i can find is clear @ mobile solutions
@SparkedEd12 жыл бұрын
@Got5pl You can try contacting Soundstream
@SparkedEd12 жыл бұрын
@poweracoustik267 I will be selling an 18"
@CFH4E13 жыл бұрын
hahaha ive always done the battery thing after i install stuff to see if its all in phase i never seen anyone else doit though
@SparkedEd13 жыл бұрын
@trancedj77 haha, He was the inspiration
@SparkedEd13 жыл бұрын
@ShowtimeSPL BTW, I am a professional woofer builder at a factory and never wanted to show a recone vid because of some Trade secrets I may let out. But a bunch of viewers kept asking for one. So whalla! And I couldnt narrate myself that day because the audio got screwed up. that's a behind the scenes secret.
@SparkedEd12 жыл бұрын
Cause I like to have fun with my vids.
@SenorDennis12 жыл бұрын
Wtf the computer voice totally ruined this video. Couldnt even watch it
@Got5pl12 жыл бұрын
Is it possible to get a recone kit for a Soundstream T4 15"?, Im in australia.... The whole coil is catus.
@DJInclined11 жыл бұрын
is one of those an old DAD woofer?
@SparkedEd12 жыл бұрын
@warmaster5128 I made them myself
@korebrent123412 жыл бұрын
I was about to ask where u get your cones but read you made them u have a skill set to be envied son
@randomsavage52012 жыл бұрын
aye man, how could i purchase a couple of these woofers??? and what is the power ratings on them????
@LordPS312 жыл бұрын
i always prefer wrapping the tape around a popsicle stick when i clean the gap. makes it much easier.
@bassabigdeal13 жыл бұрын
@ShowtimeSPL Alright dude sorry for waisting your time. Subscribed.
@perlewitzaudio13 жыл бұрын
I laughed out loud while watching these guys make faces!! LOL!!! :)
@cotyballs13 жыл бұрын
Liked the vid man. Great instructions for peeps that haven't done it
@jesseadkins18713 жыл бұрын
exactly how i do my recones.. :)
@SparkedEd12 жыл бұрын
The gasket is used to line up the surround? Hmm I've never seen that, can you explain? Which model woofers? I'm curious
@krisraps11 жыл бұрын
Oww My Ge Ou Double D , You Talk Like Snoop De Ou Double G..
@Dicer69r12 жыл бұрын
where do i get recones? i have audiovox subs theyre kinda rare but i blew the hell out of them
@bigcurt01112 жыл бұрын
I have kicker cvr and my adhesive dissolved around my cone what can I use to seal it back
@airforceranger4813 жыл бұрын
always love your vids bro... imformative... yet funny as hell
@SparkedEd13 жыл бұрын
@teamfapa check out fixmyspeaker ,dot, com
@hrdcoreme2 жыл бұрын
I have laughed at this subwooofer so hard probably to hard but it’s so funny
@saedabumokh957711 жыл бұрын
The title attracted me, but i managed to get out of this video because of that voice.
@SparkedEd13 жыл бұрын
@splaudio1 lol, thanks dude
@ivgen198711 жыл бұрын
are you selling them? or do you know where can we buy a recone kit? please help us
@Quekil83013 жыл бұрын
Loved the video guys i got a question Can you recone any sub woofer or certain ones
@Alexlivingloud12 жыл бұрын
lmfao at the voice..LIKED!! funny and informative.. thats what i like to watch...
@SparkedEd12 жыл бұрын
GOOP is the brand I prefer
@SparkedEd11 жыл бұрын
Amazing GOOP will work, or epoxy meant for plastics. Just scratch up the plastic with sandpaper first.
@SparkedEd13 жыл бұрын
@importracer4life69 lol, sorry, it was glitches in my editing program. I need a new computer.
@Warl0k12 жыл бұрын
Seeing the video but hearing Mr Hawkins speak made this video so worth watching.