Thank you Simon, not published anything for a week or so as have been away, more to come this week.
@luciasmoore2705Ай бұрын
Tidy Job mate, thank you
@rpsspain1966Ай бұрын
Thank you for your support!
@paulyoung-gb2sy Жыл бұрын
Just changed a front bearing hub on one yesterday...surprisingly easy
@rpsspain1966 Жыл бұрын
it was for this one kzbin.infolZEb9T1ygO Engine out at the minute, hopefully get away with bottom end shells, however there was a lot of shiny bits in the oil.
@simonbone11 ай бұрын
I did the left one last year, which was straightforward apart from some very sticky bolts. This year I did the other side and everything was seized together - the knuckle, backing plate, and bearing. Fortunately, replacement parts not too expensive. Also a good time to replace control arms, drop shafts, and possibly tie rod ends. Fairly simple compared to the rear suspension, at least if you're doing it on the driveway.
@jimbowen501 Жыл бұрын
I have a 2013 petrol qashqai and When a mechanic says the drive shaft is totally fudged does he mean the whole front drive shaft or is it something totally different and is the prop shaft...I had cruching coming from front suspension the last month and got really bad this morning and all i could here was banging and the car was going really slow.
@rpsspain1966 Жыл бұрын
I can not answer for your mechanic, totally fudged is not a diagnosis, he needs to be more specific.
@ashleyseeley84096 ай бұрын
Do you have to drain the gearbox oil when you changing it?
@rpsspain19666 ай бұрын
You will lose oil if you pull the shafts.
@bkfilms5843Ай бұрын
@@rpsspain1966Yh but how much oil ….
@rpsspain1966Ай бұрын
@@bkfilms5843 If you drain the oil apprx 2ltrs. you need to check the spec for your vehicle gearbox......Manual transmission, RS6F52A, 6-speed Gear oil (Preferred lubricant specification) Homologation OEM Temperature Viscosity Nissan MT-XZ Manual transmission RS6F52A Gearbox refill 2.0
@MadZprod23 Жыл бұрын
Hiya mate, my qashqai's drive shaft bearing carrier snapped, do you know if you can buy the complete bearing and carrier seprate from the drive shaft or is this going to be a new drive shaft job. Tah
@rpsspain1966 Жыл бұрын
Bearing carrier is a separate part, not sure about the bearing though.
@daveski87 Жыл бұрын
Hi there, how much transmission oil does the gearbox take? Thanks
@rpsspain1966 Жыл бұрын
Manual transmission litres2,0 Transmission type RS6F52A
@EvertHarley1 Жыл бұрын
what whas the reason for the removal? i have a (Dutch) J11 too with a ramblin driveshaft on the right side when accelerating and when i drive up (about 1%) my lane it makes a "clongkin" sound could it be that bearing ?
@rpsspain1966 Жыл бұрын
The reason was vibration at speeds over 100 kph.
@rasmadrak8 ай бұрын
Would you say this way is easier than removing the bottom ball joint? This seems easier, although removes more components. I'm "looking forward" to doing both drive shafts on my drive way in a near future, so I'm looking for the quickest and easiest way... 😅
@rpsspain19668 ай бұрын
Thank you for watching and taking time to comment. Yes, for me as you do not need to separate the ball joint.