How to Remove Front Bumper - Audi A6 S6 RS6 - C6 4F - 2004-2011 - TOTAL TECHNIK

[@TotalTechnik]

Looking for tools? www.totaltechnik.com/selectstore

[@cnoel74]

Excellent video! Very well explained and edited so you don't have to sit through needless information like wheel removal, etc.

[@thorsten_w]

There is trick for undoing the electrical connectors which I learned just recently. I was always fiddling around with screewdriver and even bought some special tool that should help with these kind of connectors. Some I even broke with the screewdriver ;-( The trick is (and you usually don't need any tool): Put your finger or thumb on the end of the latch that holds the connector in place. PUSH the connector FURTHER IN just a libble bit (The rubber gasket inside the connector is usually allowing this) and apply a little for on your thumb on the latch. You may feel the hook poping out of the latch and you ar good to go.

[@rost061]

Thank you! You helped saving life of a kitty which happend to travel behind the grill for over 100 miles before we discovered it was there -)). Also we avoided using hammer to break the grill, so thanks a lot bro!))

[@TotalTechnik]

That's awesome - thank you for sharing that with us! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@Triggeroni]

This really helped me today, many thanks! (including headlight video, as that is why I am here).

[@eddiestorer2496]

Tremendously useful video, and your channel is full of brilliant, well-executed content, thanks.

[@TotalTechnik]

The front bumper's not too bad to remove on the A6 (C6). Nothing really too tricky there, and take note of the rear tap to release for disengaging the wing brackets, as those can be a real pain if they stick. Enjoy!

[@tayw3784]

Total Technik would it be the same to replace the bumper clips that hold up the front bumper?

[@BallOut357]

any video on how to u remove the interior speakers?

[@DakarDr]

Excellent! Saved me a lot of time. Also the headlight removal and service position videos. Thanks!

[@PoLk863SwAg]

Did today to my 05 a6 c6, to add new foglights and black smoked out rs6 grill, thank you 🙏🏾

[@TotalTechnik]

Excellent! Glad you found it useful :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@BallOut357]

can u upload a video ? what are rhe sizes of the interior speakers ? Total? any audio upgrade?

[@ВасилМихайлов-з3ч]

Excellent video! Does the bumper need to be fully removed and the washer fluid drained for the headlights to come out? Isn't there enough space for them to come out if all the wires and pipes etc. are still attached?

[@chrisbutler7907]

Thanks for a well filmed and described guide!

[@BIGZet]

Im changing Parking sensors on my A6 C6 on my own and this is exactly what i needed. Subscribed! Thanks a bunch!

[@TotalTechnik]

Excellent! Glad to hear it helped you out! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@sl077766]

I'm about to dismantle my A6 C6 V8 as the engine/box is going to be (mid-mounted) in my 1303 Beetle; these vids are proving very helpful. Did you do a video removing the engine/box etc with the subframe?

[@TotalTechnik]

Unfortunately not for the C6 platform. We have done engine removals videos on the B6/B7 (S4) and C5 (RS6) platforms currently. We may well have more engine removals coming soon! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@sl077766]

@@TotalTechnik No worries, thanks for getting back to me. How about I give you my A6 C6 so you can do the videos (complete front and rear subframes, exhaust, dash, wiring look etc etc etc. I'll have the bits I need you keep the rest for spares or sale or scrap :) I'm going to use as much as poss for my mid-engine V8 Beetle but haven't really time to strip it until Easter. Semi serious suggestion if you're interested, let me know

[@donalduckisaquak1884]

Unbelievably helpful. Thank you so much for your very descriptive instructions.

[@TotalTechnik]

Thank you, we really appreciate that :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@Przebudzony]

Hi I remove the front bumper also the headlights and i have a problem with adjustment the headlights there are a adjustment brackets and I don't have any aidea how to adjustment those brackets please send me some fotos or can you measure this brackets?

[@donalduckisaquak1884]

@@TotalTechnik I will be happy to donate. A quick question, I have an 08 A6 quattro 3.2l. I need to do a complete engine rebuild but can't find a kit anywhere. Do you have any suggestions?

[@donalduckisaquak1884]

Check your paypal.

[@vnikolov88]

Dude the VAG electrical plugs are not disconnected with a screwdriver this is a common misconception, you push it forward and pres the release with a thumb, it goes right off, doing it your way breaks connectors

[@uygar2580]

Thanks for video, bought an used 18 y.o a6, butchers already screwed everywhere, missing parts, broken clips and brackets. They also cancelled headlight washers too 😖

[@danieljensen2387]

Super well made video, very helpful.

[@TotalTechnik]

Excellent, glad you found it useful :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@nwa974]

helpfull video, but for my A6 removing wheel is not necessary just turn wheel inside and u can access the screw inside.

[@flossyht6632]

did you jack it up at all

[@Salad_Dodger77]

You are a life saver. Thank you.

[@TotalTechnik]

Glad you found the video helpful :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@tam1381]

Excellent video.

[@TotalTechnik]

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@rikkijones7553]

Really useful guide, thank you.

[@TotalTechnik]

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@bullenjao1]

Super good video man 👌👌👌

[@TotalTechnik]

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@neilt1889]

Hi is this a similar proses on a A8 D4 model ? .

[@aliothman6525]

Terbaik bossku

[@EmeqPL]

I need to replace far right parking sensor, I think I can get acces just by removing wheel and the whell cover without taking off whole bumper or is it nessecary?

[@themetalfusionologist]

That black pop out in the fender well will access the bolt behind the bumper

[@TooBlessedToStress88]

Is it on both sides? Seems like a better bet then peeling the whole fender liner.

[@skegy]

Thenk you mate job done

[@TotalTechnik]

Thank you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@AmatorElektronik]

Excellent video :-)))))

[@TotalTechnik]

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@yyeboc]

whqt size torx on the inside for the triple scres

[@skymoo75]

Great video, but could you try not advising to use a screwdriver to remove the electrical connectors for things like the fog lights. If you push the clip on firmly, then use your fingers to lift the security tab it will come straight off. Using a screwdriver on these connectors is likely to damage/snap the securing clip and make more of a problem. Since I learnt this trick I've never broken a connector since.

[@skux93]

Hi what is that tank behind the red cover on the left side of the screen 6:00

[@skylerbrehm1443]

Thats the windshield wiper pump thing

[@Ramon.marin87]

Hola maestro, cómo estás, espero que usted y toda sus familias estén bien , bueno vine a este canal porque tengo un Audi A4 quattro 2008 y quiero quitarle el bumper para poder sacar el faro . El lado del conductor está dañado y quiero repararlo y me gustaría saber cómo hacer para quitar el bumper...gracias...los siento por molestarlo...y disculpa por escribir en español. Espero que me ayude

[@Fisher1903]

Excellent video, but that is not how to remove VAG connectors... that is how you break them.

[@platon001]

Great video! Very helpful, thank you. :-)

[@TotalTechnik]

Glad it was useful for you :-)

[@verlaaa]

do you think it's possible to change the bumper in 2 hours?

[@TotalTechnik]

Anything is possible :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@devinmcgee5130]

10/10

[@2024-x4o]

What nut size is te one into the bumper?

[@bemused3865]

if you mean the one at 6:42 its a 10mm, can be found by searching the part number WHT001002

[@HB-fk9sn]

You need to upload a video of how to remove rear bumper on Audi A6 c5 avant, estate or Allroad. There is no single one on KZbin.

[@TotalTechnik]

Yes, that's a good point. We'll take a look into that for a possible future vid! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@vnikolov88]

Don't pry the VAG conectors like this, YOu push them inward and press the tab they just come right off, most shops don't know it and they end up braking the connectors when prying like you are

[@pistabx]

thanks

[@TotalTechnik]

Welcome :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@jason.arthur.taylor]

I need to do this job to change a daytime running headlight I don't want working anyways. On principle, I think I am putting this up for sale.

[@TotalTechnik]

Best of luck with the sale. BTW, you should be able to disable daytime running lights on the car settings section. --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@zwosiebener]

Did it on my RS to change a fog lamp bulb....

[@TotalTechnik]

Excellent, glad you found the video useful! :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@jj-tq4hx]

Just for a bulb? That's insane.

[@jj-tq4hx]

Insane that you have to do this just to replace a simple headlight bulb too.👎😳

[@mhaff2661]

🎉

[@gjavitpacolli8447]

👍

[@TotalTechnik]

Thank you :-) --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!

[@mohamedsd84]

thanks

[@TotalTechnik]

Thank you! --- To help support us (for both you and others reading this) there are a few things you can do: 1) Donations both needed and welcome! We cannot operate Total Technik without the support of people like you! You can donate by PayPal - just go to www.paypal.me/totaltechnik 2) Please ensure you subscribe to our KZbin channel. 3) Please give our video's the Thumbs Up on KZbin. 4) Please help spread the word, the more people who know about us the better! Add links to our video's in forums, let people know about us. Thank you for your support!