How To Remove the Front Differential on BMW xDrive F10 F01

How To Remove the Front Differential on BMW xDrive F10 F01 | BOND Garage

Рет қаралды 11,374

Күн бұрын

Пікірлер

@HarlekinN57 2 ай бұрын

I was looking to change fluid for my car, 2014 535dx… and was looking at your video, and then realized you got an N57 as well! 👏

@BONDGarage 2 ай бұрын

not mine but might be on the channel more often :)

@ronaldclarke4815 6 ай бұрын

What an amazing video with details, I have a xdrive and I lowered mine and the front axel broke I replaced it and it broke again. So I'm going to do this exact procedure to make it only rwd

@BONDGarage 6 ай бұрын

sounds just like what happened here before the diff gave out

@Sonin66 9 ай бұрын

You finally did x drive content! To bad its not n55. When removing the axels, diff oil would have started to pour out. Also you could have gotten a used diff if he wanted to save his x drive

@BONDGarage 9 ай бұрын

the moment I touch an xdrive I'm getting rid of it 😅 maybe I'll put it back in if he wants to. it's really not that hard. but yea they must have lost all oil when removing the axles before. must have been dry ever since. as for N55, after changing my motor mounts I can say that it'll be the same for all 6 cylinders, gas or diesel. the periphery is pretty similar on the bottom end.

@Sonin66 9 ай бұрын

@BONDGarage x drive is nice when getting off the line in a race, and works for me in Ohio with the snow. And they are very much the same underneath when I did my oil pan gasket. I had to remove alot of the same things just to get the axels out of the way

@BONDGarage 9 ай бұрын

I feel you. the benefits are undeniable but it's also more complex. would love to have the on-the-fly switchability from the M5/M3 because sometimes I just want to pull a quick drift and other times I'd like it to hook a little better :)@@Sonin66

@Sonin66 9 ай бұрын

@BONDGarage that is true, want to drift in the snow but it does make it hard

@sokola311 4 ай бұрын

Where did you get those lights on your garage ceiling? I need those. :)

@BONDGarage 3 ай бұрын

aliexpress. there's a video on it on the channel. made a custom layout and had some leds go out already. the internals are kinda flimsy but haven't found anything more substantial. absolute love it though!

@highendtrends3508 Ай бұрын

Would you say that changing the fluid can possibly help prevent this from happening?

@BONDGarage 29 күн бұрын

possibly. in general, transmission/diff fluids should be changed regularly like all 50k miles maybe. the oil does pick up all the debris and shavings from normal wear. but in this case I believe they accidentally drained the oil when replacing an axle and then it just ran with too little oil.

@adilnicolasgundogar8534 2 ай бұрын

Habts ihr das wegen Xdelete gemacht kann man das dann ohne differntial fahren? Wie habts ihrs mit der radnabe gemacht? LG:)

@BONDGarage 2 ай бұрын

radnabe sollte nicht rausfallen. wenn man ganz auf Nummer sicher gehen will könnte man das achsegelenk zerlegen und wieder anschrauben. die RWD Modelle haben da aber auch nix.

@FawadFerouz 8 ай бұрын

Did ABS and other warning lights came on the dashboard? How was that handled?

@BONDGarage 8 ай бұрын

no lights. no nothing. even without x-delete flashed. drives like a rwd. but got x-delete flashed now just to be safe

@cristianzmara2369 Ай бұрын

Bravo!

@johnathandecerna4714 Ай бұрын

You didnt have the use the cv joint part of the axle to lock the rotor and wheel bearing in place?

@BONDGarage Ай бұрын

I might in retrospective even though I believe that the bearing won't disintegrate by itself. just my opinion, but the non-xdrive models have almost identical bearings. both are bolted to the wheel carrier and that's it. of course the axle will have to be secured to the hub in order to transfer torque but that doesn't mean that the hub will fall out without the axlehead in place. for peace of mind, yes, just take the axle joint apart and screw it back in. won't hurt anything.

@chrisclemons7564 Ай бұрын

This. Without the axle and nut in place the hub wobbles against the knuckle, creating serious drivability problems not to mention a whole slew of abs faults because the wheel speed sensor has inconsistent contact with the tone ring. Found all this out today after getting the front axles out on my f15. Will be figuring out how to separate the cv joints so I can install them tomorrow.

@hunterschroder6572 8 ай бұрын

My front diff is making a horrible noise. The fluid is like silver, shop said it would be 6k for that and the drive shaft. Couldn't I just get X-Delete and make it 100% RWD? The shop told me no but I'm thinking it's because they want me to spend the money replacing it.

@BONDGarage 8 ай бұрын

Not quite. Think about it. x-delete will cut power to the front diff from the mid diff. So that clutch is open. so far so good. but when driving, your front wheels still turn (now passive like a rwd car but still turn) and that will still keep your front diff turning. So instead of the mid diff actively powering th front diff and wheels, now the wheels power the front diff but it doesn't do anything. just dead weight. So either you replace the diff or get x-delete and remove the front diff from the car.

@name7150 8 ай бұрын

Thank you! So if I remove front diff, axles and driveshaft and x-delete. Then it will be just rwd with no problems? Have you had any problems driving that way?

@adilnicolasgundogar8534 2 ай бұрын

Das Differential ist ja am getriebe dran, wenn man es ausbaut verliert da des Getriebe kein Öl? Oder irgendwas?

@BONDGarage 2 ай бұрын

der flansch bleibt ja drin und damit der Dichtring auch. haben im Nachgang den flansch mit nem Kabelbinder fixiert und das VTG mittels xdelete stillgelegt. bisher kein Verlust aber werde nochmal genauer hinschauen wenn der wagen wieder vorbei kommt.

@adilnicolasgundogar8534 2 ай бұрын

@@BONDGaragedanke für die antwort, welcher Flansch? LG:)

@mpmp1093 6 ай бұрын

What about wheel bearings?I think better to change too?😊

@BONDGarage 5 ай бұрын

you think so?

@Tony-jv5pr 5 ай бұрын

Did you try to lift up the engine and remove it from the bottom?

@BONDGarage 5 ай бұрын

I did but it wouldn't give me enough room to take it out. that attempt didn't make the final cut tough.

@Tony-jv5pr 5 ай бұрын

@@BONDGarage I see I was able to do it. I need your help can't remove the sub frame. I see the 2 bolts in the back to remove but don't see the bolts in the front to remove it. Can you help to understand this and I can explain how I did it.

@BONDGarage 5 ай бұрын

@@Tony-jv5pr I wouldn't and didn't touch the subframe. you loosen that thing, you'll have to align your wheels. just support the engine and remove the engine mount and arm like I did. you'll have to feel for the bolts that connect the arm to the block though. they'r tucked in.

@Tony-jv5pr 5 ай бұрын

@@BONDGarage OK I feel you, I don't understand because I'm changing my oil pan gasket that's why I need to remove it.

@BONDGarage 5 ай бұрын

@@Tony-jv5pr oh I see. in that case it'll have to come out. will have to do that somewhen soon too.