How To - Replace a bumper on a 2003-2008 Toyota Corolla step by step

[@Cashewthenut]

Really gained my confidence on working on my car :)

[@jakeandcameron7022]

That’s Awesome to hear, Thanks!

[@elizabethademi2740]

Love the way you just threw the old bumper outta camera view lol

[@kerrylee4489]

Thank you so much for being clear and concise! I looked at 3 other videos yet yours was the only one to go step by step. Cheers for Portland Oregon ❤️

[@jakeandcameron7022]

Glad we could help!

[@HiddenMoonVisuals]

Thank you for video bud! helped me teach my brother in law how to swap his smashed bumper.

[@rtcar6990]

Awesome vid and nice instructions. Thank you. I’m now going to pull off my 06 Corolla rear bumper to heat gun a dent out of it.

[@jakeandcameron7022]

Thank you!, Good luck with the dent 👍

[@cbeuning]

Same!! 06 Corolla S w/ dent in the corner (slow hit in the parking lot) I was thinking a pot of hot water and press back into shape! ;) Have 400k miles on this 06 and she is not done yet!

[@rtcar6990]

That’s awesome miles. I use a heat gun to heat up from back side until I can feel ouch that’s getting hot heat I can feel from the painted side. I’ll put the bumper down on a blanket and holding the rest of it up with my hands I step on the dent and they always pop out amazingly well. Then I’ll heat any areas again where little fine tunes needed and use a skateboard wheel to roll around on the backside to smooth out these places till it’s good enough. Never perfect but gets to where you don’t really notice the dent any longer. Too cool. Today I get the bumper off. Some rusted screws were a challenge but pretty deep dent popped out great. Thanks for your comment !!

[@ThanhNguyen-ns5xx]

This video is very clear, excellent. Thanks

[@jakeandcameron7022]

Glad we could help

[@THOREAU79]

Short & sweet, don't you hate those videos that go on forever...

[@warrenhart3255]

Excellent explanation nice quality im here for more good job 👍🏽

[@jakeandcameron7022]

Thanks!

[@Welder6131]

Nice job, easy to follow

[@dragontiger5560]

Great video, are there clips on the lower area not sure what there called its connected to the rear bumper, tnx

[@mannytim7670]

Thank You helped me remove my 2006 corolla bumper

[@dragontiger5560]

Great video, my 2005 corolla S rear bumper flares were damaged can I just remove them completely, tnx!

[@jakeandcameron7022]

Yes there is a couple of clips on the back side of the bumper

[@dragontiger5560]

@@jakeandcameron7022 tnx for the quick reply, so basically once I remove the bottom flares on both sides it'll look like the corolla le bumper then, tnx!

[@jakeandcameron7022]

Yeah, it will just have a couple small holes where the trim pieces attached

[@dragontiger5560]

OK tnx!

[@shaunsingh8113]

Thanks for the great video

[@Jim80thinner]

I have a dent in the rear bumper cover. If I take the 10 mm fastener off, pop it off the side clip. Would I be able to reach in a corner add pop the dent out?

[@Randy-ul5hy]

Tip: Buy the clip puller tool. Its only a few bucks and saves you having to replace the plastic tabs you destroy when using a screw driver and pliers.

[@jakeandcameron7022]

Yeah definitely a handy tool

[@stealthflythecoop6819]

You could just remove the right side valance from the new bumper as well no need to remove bumper

[@LifestriderX]

very good video thanks you helped me

[@jakeandcameron7022]

Glad we could help

[@swAgtaker]

Great video headed to salvage yard mate 😅

[@Randy-ul5hy]

Great video...however I should mention/add that depending on the age and model of your Corolla, there may be more work required than shown here. For example, my 2008 CE has factory mud flaps/guards attached to the bumper so they have to be removed as well to reuse on the new skin. Secondly, many of those screws/clips you may find rusted so badly that it takes more time and more tools to get the job completed. All in all though, nice instructional.

[@miguelangelgidura954]

Thanks for the explanation!

[@l502r2k]

very helpful thank you very much

[@Julees_Craft_Technology]

what is the deep socket size require?

[@JulioCruz1995]

How arre they guides for this bumper?

[@EmekaNebo-m8n]

What of my 2004 corolla if make it to padad is it possible

[@ericsprout]

You forgot to mention the seals required for the top 4 bolts so the trunk doesn’t leak

[@michaelhaile401]

Of course you don’t film the hardest parts (the clips by the mud flap)

[@danielfbej]

For me it was the one near the exuast 3:32

[@michaelhaile401]

@@danielfbej that was the easiest for me. just spray some pb blaster then use a trim removal tool to pull down the center circle. Then it pulls off by the base

[@frankoalexandermedinamolin1267]

Muy bien explicado

[@169user]

i have weird clips on the plastic peice in the trunk and i can't get them off

[@blaze2051]

Does a 2005 xrs corolla front bumper fit on a base model like ce ?

[@jakeandcameron7022]

I responded to your other comment

[@CarlosLopez-rx9bi]

Thank dude