how to replace a clutch baja 5b,5t.sc,ss

[@neliocar]

If you dont have the piston stoper , you can go to any hardwear store and get a ( 10mm bolt fine tread 1.0.pitch ) . It does the same job , no need for complicaring wire

[@aeroprecision8260]

Looks like thread SEALER,not loctite? I have never seen white loctite before.

[@modex20]

red or blue threadlock?

[@gntlawry21]

I have a HSP BJ5S and it's only a few days old and already it has problems . The main gear for the clutch has a square but with two grub screws and they come loose and the cog just spun like it had shit the clutch . In Fack the clutch was fine . The in side of the square nut is like I mill to big so I had to fill that gap and try get the square nut for the drive cog to site square on the shaft . Not easy I tell you .. but l got it and tomorrow is another day ..thanks the gavman

[@nakkie1616]

Red or blue locktite?

[@toddyrotten]

No, don't use a wire!!! Buy the piston stop. In a bind, some small diameter, soft rope or cording.

[@neliocar]

10mm bolt fine tread 1.0 pitch , does the same thing

[@kylejoslin7073]

dope airfilter i just ordered one do they work good

[@BigDuke6ixx]

If the brake is slightly engaged, it's the brake pads that wear not the clutch.

[@peterbennpan7288]

I can move my clutch bell in and out as with the pinion gear, until I have time to find out why can you tell me what might be the problem?

[@stonedjedi87012]

yep worn bearings or maybe a worn clutch go to your local hobby shop and just ask them what the maybe causing it to wobble.

[@bajamike3803]

That’s fine. Just make sure your pinion gear is fully seated on the clutch bell. I’ve built 3 bajas and they all do this, no matter what clutch system I’m using. I like the turtle racing the best. The pinion gear is keyed with the clutch bell so just make they sure that they are tight and loctite the bolt.

[@theyounggamer1429]

What happens if u use wrong size screw for clutch

[@demonetizedhistory5806]

Then ur fkd

[@gusmackie7329]

What happens if you do use the wire method?

[@stonedjedi87012]

2 things 1 it could brake a ring or the wire brakes and you have a stuffed motor or to piston gets stuck and you have a stuffed motor just buy a piston stop they dont cost that much.

[@Mroswaldo16]

Hi. Need help. I installed a mew clutch and i went to try it and it bearly goes (20mph) it has problem gaining speed. And clutch it get HOT.

[@tyeasewoods2567]

Oswaldo Castillo clutch is slipping bad

[@FullSend93]

Tyease Woods so in that case what would you suggest...im about to do my new clutch and if I come across it not gaining speed what should I do.

[@mazpr2025]

That is one nice buggy!

[@stonedjedi87012]

NEVER PUT ANYTHING INTO THE CHAMBER USE THE RIGHT TOOL FOR THE JOB JUST BUY A PISTON STOP FROM EBAY OR YOUR HOBBY SHOP.

[@robertdavis7453]

Chamber? It's not a rifle! It's called the jug! 🤣

[@stonedjedi87012]

Combustion chamber

[@supermanwhereareyounow3081]

Impact wrench will make it easier...

[@flyingcatsofthesalishsea.]

are you gona eat that mint?

[@Bathurst_1000]

hello how do you REMOVE THE GEAR DRIVE GEAR'S ON THE SIDE OF MOTOR in front of the clutch as im having problems with my one == 1/5 HSP 26cc Buggy / Monster Truck kzbin.info/www/bejne/qKHKo6F4fLmsl8k == thank you for your help

[@thesunchaser.]

just buy a freakin 5 buck piston stop! dont go with a piece of wire inside lol! :)

[@coryxj6er873]

Angelo van santen I used some folded cardboard in the exhaust port when I lost my piston stop :)

[@damianjacox3320]

Your cool

[@ygtx44]

lmao gas linkage gas nothing to do with the clutch my man