how to replace a clutch master cylinder on any car or truck

thank you for watching!!!!!
If this video was helpful to you and if you would like to place a donation, here is my Venmo and PayPal information. Or I would really appreciate it if you could share my KZbin channel on your social media. Links will be on the bottom.
#clutch #cylinder #mechanic #jabothemechanic
venmo.com/code?user_id=265066...
www.paypal.me/urbanautomotive

[@beastinowt3569]

Love the no such thing as a dumb question when your learning, wish all people were like you fella.

[@rojobela]

Great explanation! Thanks for the help, saved me about $300!

[@House.of.Adkins]

I believe you did a very good job of explaining this process. I also believe that I can follow your guidance in order to replace the master clutch cylinder on my Toyota pickup. My only concern is that the line that runs from the master clutch cylinder to the slave cylinder will also have to be replaced. Thank you.

[@DanielPerez-bb2yw]

Good job. You were really clear in explaining step by step . I like how you broke every thing down that it made perfect sense. Kudos keep up the good videos👍.

[@JaboTheMechanic]

Glad it helped. Thank you!

[@carlosmunoz6202]

Lmao "that should slide right out". "Mmmhhhhhmmmhmmm" i cracked up.

[@nothingsup7350]

Cheers legend, saved me a couple of bucks for sure. Great vid brother.

[@danielcervantes8720]

I enjoyed the video.made it clear and understandable

[@MatthewTaylorAu]

thanks for doing this tutorial, I found it helpful. one thing grated on me. Don't use standard open ended spanners on brake lines. get a Flare Nut Spanner Set, or brake line spanner set. they are wider ring spanners with a slot cut out to fit over the brake line. yes, I've been there with burred over nuts on brake lines. the small spend on brake line spanner set will be money well spent.

[@drewgolden9951]

eh the new snapon wrenches with the grip technology whatever you call it gets em done good for me and wrench pliers but yes you are right still

[@edinsmajovic8283]

Great video, congratulations and thanks a lot for teaching all of us! I realised I got a problem trying to shift gear when I start up my car. I don't think I have some trouble with my clutch pedal, I can push it down like was always, middle hard, I have proper amount of brake fluid at container. I have no idea what to do to try solve it.

[@fireblade8905]

Sir. May America bless you

[@parisifranco6879]

Good job thank you.

[@Lloyd.Browne]

Thanks good video

[@jacksonjamesphiri1819]

Very helpful... Thanks bro 🤝

[@astutiasadilottopredictoru4140]

Helpful

[@dzhuish4skin997]

You're a legend

[@JaboTheMechanic]

Thanks man that means alot to me

[@bubbahottep8644]

Great.

[@itsxercc]

Thankyou bro

[@Spartanguy1970]

Hey Jabo, I have a question. My 91 Nissan pathfinder has one bleed valve in the engine compartment, and then another down by the slave cylinder. Do I need to bleed the engine compartment one first and then the lower slave valve? Or should I just leave the engine compartment one closed and bleed from the slave bleed valve below?

[@jimmilsap1220]

On an 03lancer does the u shaped pin clip have to be removed before you can pull the clutch master cylinder through the firewall

[@superflyjt24]

Great video! One question, when you did the bench bleed, what was your procedure to close it up when you were done?

[@andymanaus1077]

I've had problems with my clutch master cylinder ever since I bought the truck. It has been replaced by a mechanic multiple times. Is it possible that the master cylinder continues to fail due to insufficient bleeding of the system? If it's not that, do you know of other reasons why a master cylinder should keep failing after a couple of years' driving?

[@mamajingmemes0241]

hello there I'm trying to replace my master cylinder but i saw your step pumping the newer cylinder.. can i bleed it thru the lower slave after i put the newer cylinder?

[@louisanaburton7079]

Does it apply for Ranault trucks

[@shus369]

Good video, I need to replace my clutch vacuum booster on my old Nissan. Do you have a video that can help me out?

[@dailybongtoker]

You the best Jabo once again saving my ass 😅

[@JaboTheMechanic]

Heck yeah. Glad to help

[@jojopaul6136]

Do I have to change anything of clutch like clutch disc/pad anything of that sort if my clutch cylinder is screwed up?

[@lucameny]

Hey I know this video has a couple of years but I had a question. I have a Nissan patrol with a clutch booster does this method that ur showing going to work for me as well ?

[@MultiPanthers21]

Great info thanks fam....

[@latronnorfleet6624]

So I have a Chevy s10, and where you put your brake fluid is where my clutch fluid goes so idk man

[@frankbatterson8588]

I have a 1990 Chevy Cheyenne 3500 and I had to take the starter out then clutch not working what do I do?

[@dch.projects]

Great video. I have a question, though. I followed your video step by step for pulling master cylinder out. The thing looks fine except for super old oil sludge since I neglected this for a while. It was almost empty too. Two questions: (1) Is it possible the pedal failed because I did not have oil at MIN level? (2) If I cleaned it out with WD40 or Simple Green, will any remaining of those products interact badly with the new oil? Thanks in advance.

[@alonzokincaid1362]

Yes, yes

[@williamsinnott5771]

How do u bench bleed a master cylinder without taking out the slave?

[@RichardBullittBush]

I'm about to install a clutch master cylinder for my 2001 Ford Escape (4 cylinder). The only difference I can see so far is that my master cylinder feeds from the brake master cylinder. How different will that process be compared to what you've shown? Great video by the way!

[@JaboTheMechanic]

It's the same. It just shares the brake fluid Reservoir

[@Grandpasaab]

My clutch wont disengage fully, I noticed when I depress the clutch pedal the fluid in my resevouir lowers and when I release the pedal it raises again, does this mean my clutch master cylinder is bad?

[@steveo201]

Yes

[@luvayeavocado5377]

hey when i pump mine it doesnt build pressure

[@TheRandoGuy]

just checking, would this work on a 94 ranger?

[@JaboTheMechanic]

Yes that is correct

[@joseruelas919]

I didn’t bleed the clutch master cylinder and I have already bleed it through the small nut 10 times but it’s still not building pressure

[@truth409]

Fastest way gravity bleed with clutch up get a steady string now close a slave cylinder bleeder ..Next push the clutch down with the stick n hold Open bleader and push the slave cylinder piston all the way closed clothes and bleeder You should now have pressure...Only works on sachs slave....

[@teamotmpo2]

i put everything new on 97 honda acord n no cluch at all

[@Larry-wz5kf]

92. Nissan. Truck. Pickup. 4 cly ! Two. Wheel. Drive. !

[@truth409]

Have same truck 1994....shifts perfect one day but ok the next........I just leave the master threaed fork on inside the truck and spin the rod...

[@cssst5]

What is the fair price for a job like this?

[@oldwarsnew5722]

I got a sticky clutch.Can this cause it or do I need a new clutch

[@JaboTheMechanic]

What do you mean by sticky

[@oldwarsnew5722]

@@JaboTheMechanic nm

[@finnvon-der-trenck2592]

where’s the bleeder valve? i gotta replace mine tomorrow morning

[@nayeresfandiari520]

When bleeding you're pumping the clutch pedal not the brake, correct?

[@JaboTheMechanic]

Correct

[@nayeresfandiari520]

@@JaboTheMechanic Thanks Jabo

[@keanudewitt8959]

my clutch won’t go into gear and did a lot of bleeding

[@dnacannotchange]

I've got the same truck I've changed the master and slave cylinder over a dozen times nothing works..... But of course I never went to the dealer😢😢😢😢😢😢.. Just autozone O'Reilly's in advance auto every single 1 of their parts leaks doesn't hold pressure

[@truth409]

Dirtyfluid over n over rubber hose melting...flare leaks....parker flare seals

[@Karanbhatias]

zafira clucth master cylinder

[@charliek2462]

What are the reason for a master cilnder change

[@JaboTheMechanic]

Spongy pedal or sinking pedal

[@AverageGamer-s1s]

How much would you charge someone for you doing the job

[@AbduKaoussarani]

2hrs * hourly shop rate

[@latronnorfleet6624]

But I wouldn’t say “how to change any clutch master cylinder.” If I had a Nissan I’d be good to go though

[@chrispictures1]

Not sure if i was watching a clutch video or a video about youtube ads

[@dch.projects]

I suppose you could go find a mechanic, pay them, and skip the ads. Dude, that's how people making a living for the free information you receive.

[@latronnorfleet6624]

And mines is shitty and plastic, I should of figured that from an American made truck

[@dnacannotchange]

duralast leaks😂😂😂😢😢😢😢😢😢😢😢😢😢😢😢😢

[@indridcold8433]

Um, what is a clutch? Are those the button thingies on the steering wheel that make the transmission shift? Is that what is called autostick system? I knew some one that had an autostick car. I think the clutch cylinder was going bad because he drove it like a regular car with no pushing the buttons on the steering wheel. Maybe she took out the clutch and let it drive like an ordinary car.

[@lucameny]

Hey I know this video has a couple of years but I had a question. I have a Nissan patrol with a clutch booster does this method that ur showing going to work for me as well ?

[@lucameny]

Where yours connects to the pedal that’s where my booster connects to and then my master slave connects to the booster