Dude u r by far the best mechanic on here. The way u explain things r dead on. Ur not too fast or too slow. No wasted time or annoying intro. Nice and calm. Thank u . I had no idea about using meter and testing with dc for tps sensor. And ur paperclip to allegator clip truck is so neat I use it on everything with tight spots. Thank u so much. Keep slinging the wrench
@CarsNToys3 жыл бұрын
Thank you! I truly appreciate it. Cheers.
@daviddarviewsandmore169721 күн бұрын
Hey I have a NISSAN FRONTIER 4X4 4 cylinder and it is showing a throttle response sensor I put in a very cheap sensor from Amazon and it is showing the same code please help me?
@daviddarviewsandmore169721 күн бұрын
It's a 98 Nissan Frontier 4x4 4 cylinder.
@puffersparadise4817 жыл бұрын
and i liked the fact you cut out all the unnecessary talking short and sweet
@CarsNToys7 жыл бұрын
Thanks. I'm usually on a time crunch it helps.
@whitenugget37504 жыл бұрын
10mins isnt short lol
@tracyjackson79303 жыл бұрын
Thanks. Watched a lot of these videos and yours has been so helpful Have an 02 Nissan Xterra supercharged 3.3 4wd. Any videos on idle air control, ignition switch, how to track down a short and cat converters. Or how to bypass supercharger all together. Thanks again and GODSPEED
@petar4437 жыл бұрын
Why there are 2 connectors on the TPS?One you shown is reference,signal,ground(brown connector)..Why is the gray connector needed?Where the wires go?
@michaelhernandez38095 жыл бұрын
Hey buddy I just wanted to say I really appreciate the time you took to show these methods and skills. I've been stuck for a minute with this tps sensor. What model car are you working on here?
@brianrainey33665 жыл бұрын
I already watched this once when replacing the TPS on my 95 Nissan maxima the first time. But I'm replacing it again. I thought the transmission was going out, it was slipping so bad. Some one told me to test the TPS because the idle was surging up and it was bad, replaced it and no more transmission problems. Thanks again as always for the videos!!
@CarsNToys5 жыл бұрын
Good stuff man. Glad to help.
@mikaylavery2 жыл бұрын
Really hoping this solves my issue too 😭 Sounds the same as mine
@bradpyron89282 жыл бұрын
@CarsNToys Sir, I just watched your videos 6 years after you’ve posted it, do I still a chance to respond to my 2015 Nissan Xterra throttle body I don’t know how to test it
@elkuartostudio2 жыл бұрын
Did you have any codes?
@brandiparvin6355 Жыл бұрын
@@CarsNToys i can't find my sweet spot. I dont have a thing to check it. My at oil temp light came on after trying to adjust it. Any advice?
@ringmaster3047 жыл бұрын
base idle speed for 98 nissan quest
@gabrielbigcat86987 жыл бұрын
I love you videos I drive a 96 Nissan maximum I've been able to basically fix my car because of you and your videos thanks you so much
@kurtmcclure12243 жыл бұрын
Hey man great video. What should idling speed be of 2002 Nissan Frontier 3.3 L V6 ??
@xayy90222 жыл бұрын
1800 rpms
@danwilliams96254 жыл бұрын
Hey just wondering if the turning the key 20 times trick works for all Nissan’s, I’m in a 2002 Nissan Frontier 3.3L
@juanftw59283 жыл бұрын
Where did you hear this? I also own a 2002 Frontier 3.3L
@FrogRogers Жыл бұрын
great vid. I do have a question. We have a 2003 Nissan Frontier where we replaced the TPS, but now it wants shift funny between first and second. Revs up before shipping from 1 to 2. Like 3000 rpm then shifts. I read a lot where it says the TPS needs to relearn the transmission, but every relearning pattern I've tried doesn't work. It still shifts funning from 1 to 2. Then I got a code for TPS low voltage. Does this mean that it's just not adjusted right? anyways I'll take any help you can offer. 2003 frontier 3.3 auto trans. thanks again
@touchofgrey53725 жыл бұрын
You forgot to tell them to have the engine hot!
@dustinward79473 жыл бұрын
Thanks for Answering my question.
@fernandorivera71557 жыл бұрын
Awesome video; I just changed the TPS in my 2003 Infiniti QX4 and notice I did it wrong by placing the TPS metal tab in the opposite side of the throttle. Thanks for this video.
@c182ifly5 жыл бұрын
What is the base idle speed/RPM on a 1995 Nissan Pickup with a 2.4 L4 engine and how do you reset the RPM memory on this engine?
@frankmontez68535 жыл бұрын
John Peacock did you ever get a response from him?
@tumadre10144 жыл бұрын
Did you?
@tank215753 жыл бұрын
Did you get a response
@jeremyjamison90112 жыл бұрын
2002 Infiniti G20. Followed your instructions for no multimeter. Also attempted the reset via the 20x on/off. Worked better BEFORE changing. Help!
@randybeard60407 жыл бұрын
Note before you remove old TPS, take a sharp object and mark plastic part of sensor and housing it sets in-use these marks when replacing new TPS---just like timing marks used on older cars.....
@CarsNToys7 жыл бұрын
That's a great tip!
@c-yabugginout75735 жыл бұрын
131 dislikes = 131 people who didn't get the "I want to lay in my bed and eat potato chips while my problem solves itself" answer. Great video. Thanks for being a good teacher!!
@CarsNToys5 жыл бұрын
lol..thank you
@memberson5 жыл бұрын
THANK YOU GOOD WORK I JUST CHANGED MY TPS ON A 93 TOWN CAR WITH IS THE TPS SETTING?
@taviasmith77064 жыл бұрын
02 nissan maxima gle and the scan tool tells me that the tps is too high then to low and it will not give me any rpm when pressing on the pedal. Have replaced the pedal throttle body fuel pump and a lot of things
@bekithembasibanda67923 жыл бұрын
No wasting time, straight to the point,that was nice n brief
@ejigiri128 жыл бұрын
very, very educative and on point. My 2001 Infiniti I30 idles up and down when heated up. this been going on for a while. I've changed MAFS, Throttle body more than once. However, they're used but the problem continues. sometimes it stalls, you push the gas, the car don't move and you can see the meter go up but not moving. I'm fixing to change the position sensor like you did. but it's had to get around it for lack of space. Can you help. thanks.
@Z33Garage4 күн бұрын
You would not happen to know which wire on an 03 Xterra it would be ??
@dfields95113 жыл бұрын
8:23. Reset TPS procedure Does this also work for a 2001 maxima? I am having strange idle issues. I have tightened the throttle cable bolts which got lose. It idles at 700-800rpm fine but my son says sometimes it randomly revs up and down when in park after 3-4 mins. Like when you are waiting for a curbside order pickup. I do see the TPS change on my live data when pausing the gas. Can you disconnect the TPS brown connector while it’s running to see if the idle smiths out? If it’s happening I haven’t been able to reproduce it. Could this also be IAC? No codes present with my scanner other than p0744 (transmission TCC) Throttle body was recently removed to replace rear valve cover gasket. And cleaned with carb cleaner as shop blue towels.
@murkinranzyz99615 жыл бұрын
Great video excellent on giving the information and examples and details
@KalelMares7 жыл бұрын
Thanks, It did help me a lot. I removed mine, and when a placed it back it gave me problems, but now I know why, I never imagine I had to adjust the throttle.
@ashleytouchet1974 жыл бұрын
Im having trouble with my throttle i believe its the tps bc my idle is horrible. This helps i dont know if it would be this tho bc it does almost die on me while driving it. Like sputters. I love my nissan tho thanks for sharing
@romarhafnaouiwellhereweare25832 жыл бұрын
If the plugs are good how do you know if the sensor is bad? I went to autozone cuz my check engine light was on. It came up as throttle pedal position sensor a circuit. Can I just order a new sensor and put it in? Or will the reset trick work? 1997 Nissan pickup hardbody… 🧐
@markdarais86212 ай бұрын
Need to adjust throttle position sensor on a 2001Infinity I-30, so which wire to a touch for multi-meter reading? THANK YOU
@donpavlik8215 ай бұрын
Great stuff C.N.T. I'm working on a 2001 Infiniti I30 3.0 Liter. What would be the Base Idle Speed, Which Leed do I insert the paper clip, and how many volts am I looking for? Thank you in advance Don in Boca Raton, Fl.
@Dhi-fe5eu2 ай бұрын
Very well explained. Thank you. My manual in my Kia doesn’t say anything about the turn key in and off 20 times. So I hope I’m ok.
@aaronwellswellsoguikk93726 ай бұрын
Good information dude,. ,"?" For you can do that reset 20 times for a Cadillac DTS 2006.ya bro I just don't have that high tech gadgetry. Lol but ya Bro if you can let me know I would really appreciate it...
@coeniejvr4 ай бұрын
My GWM Steed 3 idles perfect at 700 RPM and then at random times climes to between 1500 - 2500 RPM for a few seconds and then drops back to 700 RPM and sometimes drops to below 500 RPM and then stalls. Bare in mind the catalytic converter has been removed about 3 years now and never had this problem before. What can be the cause?
@tanyabrown44492 ай бұрын
Thank you so much for your video. I have an Infiniti QX4 and I was replace the TPS on it but I can’t get it to start so I do believe it is the spark plug number two boot so I have to take off. I appreciate you. thank you for the video.
@peterpan19983 ай бұрын
Hi thanks for this great video really helped me a lot but i would like to get a precise adjustment using a multi meter i drive a Nissan Sentra 140i twin cam 16 valve if you could possibly guide me to the correct wire to use on my plug that would be really great thanks.
@coffee-xg6my7 ай бұрын
What about a TPS that has only has the screw holes that can't be adjusted and fits on one way only"? I just put on a new TPS on a 1997 Toyota Avalon (I disconnetd the battery first because I was told to do that before I even take the old one off). Both the original Toyota TPS and the new replacement part just have two stationary screw holes that are non-adjustable. (only fits on one way) I did however, notice that I had to twist the sensor slightly in order the match up the screw holes after inserting the part on the little gear inside the TPS Throttle body mount. (it was maybe a 1/4 inch off. The sensor has a little tension spring inside that allows you to turn it slightly to match u the screw holes. I'm assuming no adjusting of the sensor would be necessary since it only fits on one way? Or is there some other adjustment that I'm not aware of? Also, once I've put the new TPS on, how long does the ECU take to re-learn the new TPS and respond accordingly? And will I see improved performance immediately after installation or will the car continue to run badly until the ECU finishes relearning the new part? Thank you!
@robertcorcoran8408 Жыл бұрын
I have a 2000 maxima 3.0 did a tune up cause mileage it was due for one. Car was running fine prior changed plugs used oem and coils also oem tested have spark at each cylinder. Changed Mas, pcv, ignition condenser, and crankshaft sensor in front now car runs horrible. No power takes 5 seconds to hit 10 mph and will run 1st to almost 7000 and then bang to second. ANY THOUGHTS PLEASE IM STUMPED
@stellamatutina35735 ай бұрын
Hi CarsNToys, I'm wounding If its the same principal for the Nissan Narara 2000 D22..?
@junior.the.touristАй бұрын
Hope your still active in here looking for the specifics for 2001 Nissan Sentra
@briantallman3161 Жыл бұрын
I replaced my TPS on my 2001 Xterra. Thought that I had found the "sweet spot" you referred to. Now, when I drive it, the rpms will jump and fluctuate rapidly when accelerating. From what I can tell, it happens in 2nd gear (though i could be wrong). It did not happen before swapping the TPS. Do you have any advice? It is a 2001 nissan xterra se v6
@kashiflf8 ай бұрын
Nissan sunny 2006 automatic gear jerks while shifting on 2nd gear and little on 3rd gear also? Is it the problem of ETB
@johnl.9523 жыл бұрын
As you rotated the TPS past the sweet spot you described, you can hear a type of buzzing in the background. Then as you rotated back towards the sweet spot, it went away. What is that buzzing sound ?
@jluiscruz7240 Жыл бұрын
Hi I wondering how to replace the oil pump on a 1994 Nissan Pathfinder XE 3.0L manual transmission, if anybody can help me with this. I’ll appreciate it Thanks
@mikel5992 Жыл бұрын
Hello, thanks for the video. I have a 2007 Toyota Tundra. I accidently killed the battery while working on it. Now it idles at 350-400 rpm. I've tried every technique on here to reset the idle. nothing is working. Any suggestions? I might try and adjust the TPS or clean throttle body but it idled fine till I drained the battery. Thanks in advance.
@adamarek3009 Жыл бұрын
Hello. Nissan Sentra 2002 RPM in parking 750 after driving at the stop with gear it drops to 300RPM and starts to shake. I cleaned throttle body and replaced IAC actuator, cleaned mass air flow sensor. What’s your advice?
@khaleelhusbands4 жыл бұрын
Hello. Do you know what the base idle for have a 2004 Infiniti i35?
@amustsuccess Жыл бұрын
Thank you for the video. My car (Nissan Altima 2013) works fine in reverse, but does not get past 2 rpm on drive mode. What do I possibly do to fix the problem?
@jaybae8056 Жыл бұрын
i just picked up a sweet '96 pathfinder 4x4 5 spd manual. with a couple of codes. p0120, and p0325. i am qbout to change the TPS, and if you could help a bro out with odle speed info etc, or idle re-learn procedures, i would be so very grateful
@sidclaim5 жыл бұрын
I have 2002 Nissan Frontier 2.4L with 210 k miles. Started with P0302. I replaced plugs, wires, distributor cap, fuel filter and fuel injector. I have spark on all plugs, harness were tested. Rough idle, below 500 rpm on drive. Came with new service code P0505 and p0300. Any suggestion?
@waynejohn11602 жыл бұрын
Thanks for info .... I've a 1993 nissan bluebird sss with a sr20 engine I'm having a problem with properly setting the TPS on it could u give me some info on it ? Thanks much!
@simonsulu56724 жыл бұрын
Have a problem with my Nissan Xtrail SR20...the accelerator pedal sensor keeps blowing every time I fitted a new sensor....vehicle cant start now..Any help please..
@RETARDEDFATTKIDROBOT3 ай бұрын
Nice vid. I just wanted the voltage specs to test my current one and to set the new one if it needs replacing. Lost my nissan FSM bundle for a wide array of cars to mold
@salsinger9985 Жыл бұрын
please help .. after mechanic cleaned my IAC my car kept rev up & down after it get warm ( from 1000 - 2000 RPM ) repeating .. did all the relearning idle no help .. i don't know if the TPS is the problem for idle repeating rev , or of the Mechanic missed with it ..
@TyroneMaye10 ай бұрын
Hi i have a 2007 Audi Q7 3.6L V6 engine. My first question is how can or do i bench test of my gas foot pedal with the sensor attached to it ? Second question is what is the idle rpm for my model Q7 ?
@mariavaladez79813 жыл бұрын
Hi cars and toys. Mi car is an old 1985 Nissan 200 sx coupe. And Im thinking Im having that Problem. Low idle ...stalls.. And I can see the sensor is broken
@emsman592 жыл бұрын
You seem to be pretty knowledgeable, I NEED your HELP! Can you please show me if I or how I can bring up my RPM idle speed say 100 RPM on my 2006 HUMMER H3? Please help me.
@nickryan64696 ай бұрын
Good day. Can you please tell me the volts and idle speed for 2002 nissian xterra 3.3L manual transmission. Thanks
@keralavibes30504 жыл бұрын
Can you make a video for EGR valve
@CarsNToys4 жыл бұрын
Sure. Here you go: kzbin.info/www/bejne/gmjcc598q6yGp7M
@STARFIRETRANSPORTLLC7 ай бұрын
1994 mitsubishi mighty max 2.4l. Replaced tps, cap,rotor,wires,but can't seem to get the truck to start or it starts and stalls. Looking to find how many turns on the idle adj. Screw and there is also another on opposite sit of the butterfly where cable connects. Appears to split the butterfly . It has mikuni throttle body efi any info would be greatly appreciated
@dahammanasa303610 ай бұрын
Your educational presentation is very precise. I have a 2000 Infiniti i30. I would appreciate if you could send me throttle position specifics for this car. Thank you
@Duwhop312 жыл бұрын
Hey Bud i have a 2007 Nissan Maxima 3.5L & i unplugged & cleaned the Throttle Position sensor & now the rpms r very high & it has a P0507 code. Everyone whos had this problem needed to do the idle control system relearn. But Im not sure how to do it. Any help would be appreciated
@thesetruths14042 жыл бұрын
Hi. I've got a 2003 Montero Limited 3.8L. Twice so far (1,000 miles apart) mine has gone into a condition where it will not accelerate. It idles and starts fine, but will not go over 40mph on level road, and takes a long time to get to that speed (severel minutes). It will be fine one moment and then begin this malfunction in the middle of driving it, in town or on interstate. I do have a TPS sensor code (P2135) but also cam and crankshaft sensors codes. The timing system is fine and it doesn't jerk or do anything strange except refuse to accelerate. I can turn it off and after 20 minutes it will operate fine again. Is the the TPS sensor getting hot and then it fails?
@boygeorge68087 ай бұрын
hi, i find your video so interesting, im trying to figure out if my nissan murano 2017 has a throttle position sensor because I know I am having a problem on its idle and hesitation during shifting. pls help me to locate it if I have one. thanks in advance.
@TheKillerkyle_7 ай бұрын
I have a 1998 Nissan frontier 2.4 L five speed manual that is rev bouncing. Can you get me the wires I need for the multimeter and the voltage I need to be at.
@kylemoore13879 ай бұрын
Hey there , i have a 97 pathfinder and im having a hard time adjusting my throttle position sensor, im trying to find IPM sequence and cant find it anywhere please help!!
@Jack144322 жыл бұрын
I opened my throttle body and cleaned it, also cleaned the position sensor now my car having issue when I start moving the rpm goes suddenly up and down in low gears below 60 kilometers per hour. And has some rough shifting. I adjusted the sensor as you explained and reset the sensor without a scan tool as you explained in the video my RPM is around 800 and the car runs with no issue above 60km. What could be the problem any info would be appreciated. 🙏🙏🙏
@lowkeydjab1814 Жыл бұрын
I have a 2013 Nissan Maxima the throttle body went bad I changed it, I changed my fuel pump but now it only revs once I first start it on park, once I put it on drive it don’t rev the rpm stays at 1000 just enough to keep the car rolling
@sugashack74 Жыл бұрын
Dude I just want to kiss you on the lips so hard. And I'm totally straight.. you have no idea how your instructions have helped me out. I have a 1997 Nissan Maxima the only thing is my screws were stripped at the head. I had to just break up the sensor and use a pliers to screw the screws out. This sir has saved me so much headache. My 97 Maxima has 312,000 miles and of course that part would have gone by now. The shift points are so much stronger now.
@christinaakatbird8201 Жыл бұрын
2000 nissan Pathfinder. It sat for 3+ years, it was given to my child and the idle runs high and will not shift past 2nd and the RPM will jump up, we shift it into 2 low and the rpm will come down but its not shifting. We were told the rpm's were not adjusted but I have never seen where you couldn't manipulate to get the vehicle to shift. We did change out the trans fluid without flushing it or cleaning off the magnet. and that did help a lot but still have the issue. How can I trouble shoot the issue? one time it did not want to go into reverse but it only happened once and that was right after it sat after an accident.
@anthonyplew88462 жыл бұрын
I have a 2008 Buick Lacrosse with a p2138 code come up n it saying throttle position sensor however I cannot find anywhere to purchase a tps. Can you lmk where please?
@joseaguilar3377 Жыл бұрын
Hi I have a 1988 nissan pick up D21 with a problem, it doesn't go over 3000 Rpms and I could really use some advice
@bbear3763 Жыл бұрын
02 Xterra 2wd Auto. Idle goes up and down or surges when cold. After it warms up its ok. Seems to idle high. I believe I need to adjust it. No codes. Adjusted it now its shifting funny. Ordered a new sensor and trying again.
@1NcognitoXx Жыл бұрын
Well, just did the replacement, and now when I rev in park it surges up and down quickly until I release, or I can sort of rev through it and it smooths out over 4k rpm. But when driving it feels so much better, so I am just gonna roll with it until it gives me trouble. I did the 20 ignition turns to hopefully reset it, and the idle air reset attempt. It acted the same before and after the idle air reset attempt. Did I fail the 20 key turns or what the hell is going on?
@guillermomartinez79073 жыл бұрын
I've been working on my sons 2005 nissan Murano changed the cover gasket and spark plugs and disconnected the throttle now I can't get it to relearn the idle I can only get it down to like about 825 rpm and I read that it has to be between 600 to 800 rpm can I perform this technique to get the idle down cause the check engine light keeps coming back on with the same code P0507 Please Help Thank You
@Paul27Sultana2 ай бұрын
Does the turning thr key 20 times work on a 2001 Oldsmobile Alero?
@johnroggy80993 жыл бұрын
What are the ideal rpm for a 2001 Mitsubishi Montero Sport XLS. Because I'm going to change the throttle body position sensor on my car. Thanks
@colandaigle66683 жыл бұрын
Hi I need some help I have a 1997 Nissan pathfinder 2 wheel drive 3.3 engine I have change the IAC,and the TPS and the MAF and the knock sensor and still have a surge when idling at like a red light ok I actually changed TPS twice really don't know if it really needed to be changed the second time but it kept throwing me the knock sensor and TPS codes even after changing them it is still throwing those two codes I need to know exactly how to relearn all those sensors to get my pathfinder to run right can you help me
@davidnewhouse1347 Жыл бұрын
hi my daughters 98 maxima had bad injectors so i took the top end of the engine apart to replace injectors and while i was at it i replaced the coils. i put everything back together and the car idles super high (6-9k rpm) but if i put it into gear it settles down to around 2-3k drives for a lil bit then dies....i didnt touch anything on throttle body at all ...any ideas on what it could be.
@JennyB-ii6sw Жыл бұрын
I have a Nissan Xterra and was wondering if you could give me the base idle for it.. as we was the DC that it's supposed to be please!! Thank you!!
@NicoleBasilico4 жыл бұрын
Hay there my tps is adjusted all the way back i can't get the idol to go any lower its at 1100 rpm can't advance it any. My last tps was setting it at 700 perfect shifted will but couldn't get rid of p0120 not could i confirm meter test on variable out put voltages i did every meter test i can as well three was a service bulletin to the procedure in 2006 for the 1996 maxima either way i can not physically back off the adjustment any regsurdless
@lowkey5585 жыл бұрын
Good day Sir, im from Philippines, i own a Nissan Sentra 2004 1.3 qg13 engine, the problem is when i cold start the car it runs fine for about 4-5 mins until when its hot it will start stalling, i cant even rev it upto 1.5k rpm it only talls, i wonder if its the Tps or any other sensor, i hope you can help me sir
@terryiverson83555 жыл бұрын
After 2 years it is still helping people. Thank you very much, I will look up my own specs no reason to make you do it. Thanks again.
@57westy2 жыл бұрын
I have an 2000 3.3 mercury villager / nissaan motor.which wire do I place multimeter leads?
@Crazwolf152 ай бұрын
One great way to not risk breaking the screws is to remove the throttle body from the car cuz then u can hold it however u need that's what I did for my grand prix
@daffodill70823 жыл бұрын
@carNtoys RPMS•••---} for 1999 Nissan Altima gxe 2.4l manual engine
@mandoky16472 жыл бұрын
If it's Japanese it's not a phillips it is a JIS screwdriver. Very similiar and if you find yourself camming out screws then that's why.
@elneneeserio3 жыл бұрын
Please I need the TP v for a 04 subaru x AT naturally aspired SOHC I've read it's 0.6 v while the car is on with the throttle at resting place
@robbybenjamin89394 ай бұрын
2001 nissan sunny B15, qg15 engine, specs??? Throttle position
@BaggettCyclingAdventures Жыл бұрын
Does the key flick memory reset work on an 06 frontier? I'm going to replace mine, to see if if fixes the random turning off of the truck, and going to replace the cam position sensor as well.
@llg74563 жыл бұрын
Changed my throttle body sensor in my 2001 Nissan pathfinder now when I first crank it it idles up and down. Hate I got new sensor it actually ran way better before I bought new one.
@JoshuasReality Жыл бұрын
I'm trying to raise the idle on a 2009 Ford escape 4 cylinder XLS. Can you comment on here for a way for me to do that, on my ford machine?
@briceparker52864 жыл бұрын
I have a 2004 Cadillac Srx v6, 2wd and the car hesitates when trying to accelerate the car fast and it idles rough. And would cleaning the throttle body and mass air flow sensor make the car run better.
@jasonjobe98852 жыл бұрын
2001 Infiniti I30 what’s Voltage anybody if you could tell me I greatly appreciate it
@johnwbuttram82022 жыл бұрын
I have a 95 Nissan maxima that when you rev it over 2500 it starts sputtering and acts like it's out of gas but it's got plenty of pressure and flow
@ryancrompton538111 ай бұрын
I've got a 97 Toyota corolla. What is the base voltage of the tps when throttle is closed engine not running. What is my base idle as well
@kingfila31526 ай бұрын
Great video... is there any difference changing a TPS on a cbr1000rr 🤔😊
@JohnPritchett-qk6zd Жыл бұрын
I just replaced the tps and iac on my 1999 cadillac deville. Now it is idling at two thousand rpm. How do I fix this ?
@kabibnurmagomedov197 Жыл бұрын
My 1997 nissan maxima gle engine shut off while driving or sometime when slow down at stop sign it feels like engine cutting off what seems the problem kindly lmk
@markdale2782 жыл бұрын
Thank you
@yousifAlQaisi2 жыл бұрын
Work on reading 5.89 Is this true Nissan Maxima 3000 engine
@oscarcruz60072 жыл бұрын
Cuestión,I have a infinity i30 and I replacing the TPS,what are the rpm for this vehicle?
@karloslopez70243 жыл бұрын
1993 2.4 L 4 cylinder Nissan pickup if you know the volt spec and wiring diagram
@simonkordek66522 жыл бұрын
Hey bud I have a 2004 Nissan Xterra 3.3 with an automatic transmission, need some help setting the idle