How to Replace Drivers Side CV Axle 08-13 Nissan Rogue

Buy Now!
New CV Axle Shaft from 1AAuto.com 1aau.to/ia/1AAC...
1A Auto shows you how to repair, install, fix, change or replace broken, worn, or vibrating CV axles. This video is applicable to the 12 Nissan Rogue
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oajt/1A...
• Pry Bar 1aau.to/ohA/1AX...
• 18mm Wrench
• 18mm Socket 1aau.to/orR/1AX...
• 21mm Socket 1aau.to/orR/1AX...
• 32mm Socket 1aau.to/oT/1AAS...
• Ball Joint Press
• Side Cutters
• 1/2 Inch Breaker Bar 1aau.to/okR/1AX...
• Ratchet 1aau.to/oakK/1A...
• Socket Extensions 1aau.to/o5W/1AX...
• Torque Wrench 1aau.to/ovD/1AX...
• Copper Anti-Seize
• Rust Penetrant
• Center Punch 1aau.to/ocC/1AX...
• Chisel 1aau.to/ocC/1AX...
• Drain Pan 1aau.to/ogY/1AX...
• Funnel 1aau.to/oc9/1AX...
• Hammer 1aau.to/omf/1AX...
• Wire Brush 1aau.to/oey/1AX...
For More Info visit us at 1aau.to/h/bii/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@warrenlange6106]

One of the best how to videos. Very thorough instructions.

[@1AAuto]

+WAL Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@PhillyDee215]

I usually remove the strut bolts, seems easier than removing the ball joint. Either way an alignment is recommended. Either way works tho💯

[@j3st3rjok3r]

Same here

[@chrism1130]

Yeah, after wasted time unsuccessfully trying the ball joint method, I removed the strut bolts. I outlined the position with a sharpie before removing bolts which aided in reassembly. Several videos show the ball joint method for my nissan rogue. For my outback they show the strut method. Even 1a. Would not attempt the strut method again. They should redo this version IMHO.

[@caru3257]

Thanks man. I didn't remove the ball joint and it saved me some work. Thanks for the video. I went and bought the 1/2" impact and that made it super easy.

[@shannonallen4727]

Well your alot smarter than thi s guy hey what is the snap ring on the end of the spline fpr

[@kurtgood2914]

Fantastic mechanic work

[@kurtgood2914]

This video is very helpful and thanks for sharing A-1 auto is awesome people always trying to help you,

[@MrGarrett1966]

that ball joint gave you a whoopin. there is always one bugger in a repair somewhere. never fails.

[@1AAuto]

+MrGarrett1966 Thanks for checking us out! Not all repairs can be easy all the time, this will also give a look into a vehicle that is a little more, challenging, so to say!

[@PeterCsere]

Easier way to get the ball joint out. If the control arm has ever been replaced (likely if you are driving an '09 Rogue) there is probably a dimple in the middle of the ball stud. Put a punch attachment on your air hammer and angle it downwards with the point resting on the dimple. (The shaft of the punch will be alongside the axle hub.) Pull the trigger and watch the stud gradually inch downwards - it doesn't damage the stud or anything else. Pretty nice n' easy. This even worked for me for the older ones when there wasn't a dimple in the stud, but the dimple makes it easier.

[@brapppn-can-am-man6906]

Need to do a follow-up video for the Rear CV Axels. For the Nissan Rogue.

[@SilviaJoe]

I can hear the customer pacing back and forth in the waiting room everytime you hit that ball joint

[@redlight6525]

I like the way he twisted the nut

[@bobicpfan2]

on models with aluminum rims, the lug nuts are 21mm and not 19mm. and the lower control arm has to come completely off in order to get the ball joint out of the spindle. it will not come out otherwise. it will hit on the frame.

[@franciscojavierfloressilva4197]

Excelente video. How to order both cv axles for muy Nissan Rogué 2008 from 1A AutoParts?

[@shannonallen4727]

I took off two cv joints before you got one off I just want to know what the snap ring on the spline end of axle shaft is for

[@slickdawg4634]

Good job guys

[@bdeemter1234]

thanks again guys! I just placed my order from your website.

[@1AAuto]

+Brandon Deemter Thank you for your order! We'd love to hear about your experience. Here's a link to leave us a review on Google: goo.gl/i5JFNY

[@magsteel9891]

Dealer quoted $800 for a driver side CV axle replace. Even worse, on the same quote they had: Lower control arm bushings $1150 Transmission replace $4280 So the estimate bills for the same labor multiple times. Somebody has to sue one of these days.

[@DisgustedGenXr]

mag steel dealers are pieces if shit

[@iwanta29r]

You don't need the ball joint press. You need a ball joint separator.

[@imhooks]

You also don't even need to fool with the ball joint at all for this repair. Just take out the 2 21mm bolts off the strut above and the whole knuckle drops down to give room to remove the axle.

[@sports_comics5593]

When I try to put the driver side axel back it it doesn’t go in all the way and when I look in the hole I see a thick metal cylinder pin blocking it deep inside making it not be able to go all the way inside. Any suggestions or help?

[@missourianfarmlife6331]

The pinch bolt nut was only torqued to 20 ft-lb? Are you sure that is the correct torque spec?

[@louadams4942]

Yes the pinch bolt holds the balljoint not the pressure of the pinch 🧐

[@j3st3rjok3r]

Love how easily he gets the axle out, meanwhile I've already broken 2 chisel's and 1 pry bar trying to take out mine 😒😑

[@dissectionproductions8783]

Tip: Turn the axle.. Try to pry/hammer it out.. Then turn again and try to pry again. Keep going that.. Eventually the the c ring will line up nicely and let you pop it out..

[@johncollins8304]

Thanks. 10:30...I can't get The axle fully back in the hub so it pokes out enough to put the nut on to pull it out.

[@Wanderrap]

This is awesome.Great vid!

[@milkman2591]

My knuckle was seized to the ball joint to the point where I had to replace both. Ended up cutting the knuckle off with a cutoff wheel.

[@writeupking]

Oh God buddy. You could have undone the two bolts that hold the strut to the knuckle . I've done this cv axle before in like 20 minutes 😂

[@MacAutoDiag]

@@writeupking LOL

[@awesomeness7117]

You dont need ball joint separator I did it with a hammer and pb blaster in like 5 mins

[@1AAuto]

+Dylan Wagner Thanks for the feedback!

[@Wire-Free]

Can you make or share a video for the drive shaft replacement?! By TY

[@MrMetalclay]

Could you separate the knuckle from the top instead of the ball joint?

[@johnj05]

Yes, you could separate it from the shock (top mount). But you will change your alignment and have to get it reset.

[@milkman2591]

Ive separated from the top and it didnt affect my alignment, I replaced the knuckle, ball joints and wheel hub and she still drove straight as an arrow after

[@bwmcreynolds]

Is this an AWD model or 2WD? And if so is there a difference in the process? A shop told me that there was a front subframe assembly that had to be removed to do this repair because my rogue is AWD.

[@shannonallen4727]

No difference but the parts aren't interchangeable

[@michaelmcandrews1329]

I'm looking at the parts you are woking on and my drivers side aLL THREE are broken the axel and balljoint and I don't know what the other on is called

[@jamespinckard4210]

Why use copper anti seize rather that the silver?

[@danteestacion2205]

How to order cv joint for nissan serena model 2003

[@tommyjackson5330]

When he was taking that nut off he was turning it to the right as he would tighten it as right handed thread then he says I'm going to take the nut off then he was turning it to the left what's up with that?

[@bryanrowell2054]

Did you torque the ball joint nut also?

[@1AAuto]

+Bryan Rowell There usually isn't a very good way to do that due to where it's mounted. Usually, they can be tightened well with a wrench. Thanks for checking us out! 1AAuto.com

[@kellydavis7497]

How did you get it out?

[@dannydnice1]

How much do shops ruffly charge for this work?

[@MacAutoDiag]

Around $300-$400

[@aprilsonner3286]

In FL for one side $300 to $400. Or buy your own part and they'll just charge you labor. Don't let them BS you. It takes under an hour. Really 30 minutes for an experienced mechanic to install. It should cost no more than what they charge for 1 hour of labor. You could cut your cost in half buying the part(s) yourself.

[@asankovlogs]

What about the oil came out?

[@bdeemter1234]

is the axle nut reverse threads?

[@FloridaMan7337]

No

[@kellydavis7497]

I’m having trouble getting my half shaft out on a 2018 Nissan pro 4 X crew cab 4X4

[@asankovlogs]

What about the oil came out

[@jordyrodriguez4813]

Lol you were careful to leave the nut on when hammering the axle out but when hammering in the NEW one you just went right ahead

[@1AAuto]

Thanks for checking us out. 1aauto.com +Jordy Rodriguez

[@bdeemter1234]

they used a different style hammer. its a dead blow hammer, not made with steel. no deformation on the new part would be possible

[@scarface17857]

That ball joint separator tool is unnecessary all you need is a couple wacks with a hammer and a prybar.

[@1AAuto]

+scarface17857 We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair.

[@FloridaMan7337]

I just did this job and it didn't free up with PB blaster and a few hammer wacks. This one was a bit more of a pain. The best tool to use is an air hammer with a 18 inch pneumatic taper punch. That'll get it off the quickest.

[@chrisnutt8429]

Why wouldn’t you replace the oil seal?? That’s not smart.

[@johnj05]

As a mechanic, I would have 100% no point not too. Could very easily damage or be leaking already.

[@musiclyrics5473]

YUP !! my daughters car is a 2009 Rogue and 150,000 miles. Her driver side CV boot is broken. I plan to replace the seal while I am already replacing the CV axle. This way I know everything should be good for another 100,000 miles

[@williamredford635]

The dip stick fluid ?????? Lol 😆

[@kakaa37]

Solo martillo not good

[@shannonallen4727]

AA

[@yachtyteam6978]

T