The trigger power button is one of the most common problems with the Dyson V10 and V11. In this video, I will show You how You can replace it.
Пікірлер: 210
@Nintyspong3826 Жыл бұрын
I had this exact issue and was quoted £130 and a 4 week waiting time by a local vacuum repair shop. I bought the part for a few quid on eBay, and following this guide, was able to complete the replacement myself in about an hour! Thank you for this video! For anyone else trying this I would highly recommend having good tools for it, such as the long screwdrivers with decent handles on them in the video, I had to muddle through with some cheap tools which made it much harder (but still doable!).
@techfixPOV Жыл бұрын
You`re welcome. I`m glad it helped. For sure you will need good tools, especially for the torx screws (T8). I also uploaded a new video (3 ways to fix the broken trigger issue). Is more detailed and gives you more options to solve this issue.
@sasvkm11 күн бұрын
Thank you so much for this video. I ordered a replacement kit incl two long screwdrivers on Aliexpress. There wasn't a manual. Because of this video I was able to complete the replacement on mine Dyson V11. This video is superrrrrrrrrrr 👌👌👌👌👍👍👍
@techfixPOV11 күн бұрын
Glad it helped!
@bonuch6 ай бұрын
Thank you so much! I had the same issue with my V10, so I 3D printed a new trigger part and followed your video. The Dyson works great and more importantly the wife is happy!
@techfixPOV6 ай бұрын
Glad it helped!
@dee2may Жыл бұрын
I just finished repairing my V11 and I'm so proud of myself! Thank you so much for this detailed video, it helped me every step of the way.
@techfixPOV Жыл бұрын
Yes, you should be proud of yourself, you managed to fix it and there is no need to replace it with a new one.
@pianoplaynight7 ай бұрын
Thank you so much. Lifesaver! Dyson would NEVER publish such a tutorial. The planned obsolescence is part of their business plan!
@techfixPOV7 ай бұрын
Glad it helped!
@nielsdebaets6972 Жыл бұрын
Thank you so much you saved me a new vacuum cleaner.
@techfixPOV Жыл бұрын
I'm glad I could be of help. Cheers!
@kyeparry10 ай бұрын
Me too! Tricky but well worth the effort. Thank you 🙏
@lukaszp85562 ай бұрын
Dziękuje za pomoc . Bez tego filmiku nie wiedziałbym jak wyciągnąć włącznik . Pozdrawiam
@techfixPOV2 ай бұрын
Glad it helped!
@alexanderthegreat4952 Жыл бұрын
Thank you for the very detailed video. I was able to replace the push button and everything works great. You save me $600!
@techfixPOV Жыл бұрын
I'm glad I could be of help. Cheers!
@kkkddd3370 Жыл бұрын
Thanks you covered not only disassembly but reassembling, As someone else said the V10 needs aT8 Torx, which I had to go and buy It took me about 2.5 hours and saved me hundreds of GBP
@techfixPOV Жыл бұрын
I'm glad I could be of help.
@redesX Жыл бұрын
I used Torx T9
@lukaszborek3016 Жыл бұрын
That was a perfect video! Even the stops for showing the plastic pulled back as wide as a finger. I was able to repair my V10 within 1 hour.
@techfixPOV Жыл бұрын
Thank you! I`m glad it helped.
@thomasstowell492510 ай бұрын
Great video, thanks a million, you’re 100% right they don’t make it easy to take them apart ! But you definitely do ! Dyson much like other manufacturers seem to put hi usage parts in their appliances, made of plastic, probably hoping when it breaks you’ll go buy a new one ! Thanks again 😄
@techfixPOV10 ай бұрын
Thanks for watching!
@chuscascon56924 ай бұрын
Muchas gracias. En Dyson me dijeron que tenia que cambiar toda la pieza y me dieron un presupuesto de 119 euros. Me comunicaron que la pieza se había agotado y me animé a arreglarlo yo siguiendo el tutorial. ¡arreglado por 12 € con destornilladores incluidos en el precio.
@techfixPOV4 ай бұрын
Glad it helped!
@NicolasB5 ай бұрын
Thank you for your video, I was able to repair my v10 thanks to you ! It's great that you are talking us through the steps, most videos will only show us and put a little music.
@techfixPOV5 ай бұрын
Glad I could help
@kwa_nguyen Жыл бұрын
thank you for making this video and helping us guide us through this process. could not have done it without your help. wishing you all the luck and love and kindness in this universe
@techfixPOV Жыл бұрын
Glad it helped
@obivandings3845Ай бұрын
One million thanks for your super detailed video: I replaced the plastic trigger with a metal one. Piece of cake with your help!!!!!! ❤❤❤❤❤
@techfixPOVАй бұрын
Glad it helped
@Cajuan267 ай бұрын
Excellent video!! I just finished replacing my trigger after following this video. My trigger was broken in the exact same place as yours. Got the part and the toolkit from Amazon, and, after a week, I'm vacumming again. Thank you so much. Your video it's been very helpful.
@techfixPOV7 ай бұрын
Glad it helped
@sergiolovaton10569 күн бұрын
Thanks Pal..!🍻 I have just struggled removing the trigger switch, there is a screw that has to be removed before to pull off the switch.
@techfixPOV9 күн бұрын
Glad it helped!
@michaelhopper36545 ай бұрын
Found the trigger online, this video was by far the most helpful i found, thanks
@techfixPOV5 ай бұрын
Glad it helped
@redesX Жыл бұрын
Fantastic! Just did it. You better are equipped with good tools to do it. Specially almost at the end of the dissembling you need a torx T9 (as before) but long and thin. Also a flexible adapter to reach some torx T9 as angle and space is minimum, this T9 is a must
@techfixPOV Жыл бұрын
That's right, without good quality tools, it could become very frustrating.
@Carlicuqui Жыл бұрын
… from Spain… thank yo so so much!!! Imposible without your help 🤗 ✌️
@techfixPOV Жыл бұрын
Happy to help!
@LukeKonstantinos-nd6oq Жыл бұрын
Great video, stopped watching another similar halfway and switched to this. Much better!
@techfixPOV Жыл бұрын
Thank you! Glad it helped!
@volkanbodur28893 ай бұрын
Thank you so much for guidance. Within an hour replaced trigger switch. 👍👍👍👍
@techfixPOV3 ай бұрын
Glad it helped
@suewinsley Жыл бұрын
thanks for the help. I was confused with the trigger when re assembling it as it wasn't springing out to the off poison until I saw you slide the battery back in place then it was all clear. the other thing I had trouble with was power leads connecting to the motor. After bending then up to get them out I found it difficult to get correct angle without putting a lot of pressure on the housing which I ended up doing.
@techfixPOV Жыл бұрын
I'm glad I could be of help. Yes, some operations can cause problems. The important thing is that you managed to get over it and the vacuum cleaner is functional again.
@cefecm3 ай бұрын
Excelente trabajo mostrando todos los pasos para desmontar y volver a montar el gatillo de Dyson V10. Le felicito y le agradezco
@techfixPOV3 ай бұрын
¡Me alegro que haya sido útil!
@ZchannelZZZ Жыл бұрын
Excellent tutorial video. It helps tremendously. My V10 now works perfectly again :)
@techfixPOV Жыл бұрын
Glad it helped
@paulwatson31484 ай бұрын
Great video, thanks for uploading. A fiddly job for sure, but worth the effort for the money saved. I found a PZ1 and a long reach Torx T8 screwdriver to be perfect for this.
@techfixPOV4 ай бұрын
Glad it helped!
@romlef526 Жыл бұрын
Hello thank you very much, this video will help me a lot, my V11 has had this problem for a few days, so I'm going to buy a reinforced model, and change it Thank you very much, it's very well explained!
@techfixPOV Жыл бұрын
I'm glad it helped. Cheers! :)
@romlef526 Жыл бұрын
I bought the new part (reinforced) because the original part is thin and I think it's just right and it will break in time, so finally, yesterday I did the assembly, disassembly, and replacement of the defective part with your video, and frankly nickel, I'm delighted, it was rather fast and it is working again Thank you, it helped me a lot
@techfixPOV Жыл бұрын
You`re welcome! I`m glad it helped. Enjoy your working machine! I hope you got one spare button, just in case... Cheers, mate!
@rogerhoman88589 ай бұрын
Excellent video, straight to the point. Thank you.
@techfixPOV9 ай бұрын
Glad it helped!
@user-qp7xb5uc4v7 ай бұрын
Огромное спасибо за это видео! Благодаря вашему видео я смог легко поменять курок пылесоса! Все было снято очень подробно и четко! Это мне очень помогло! Спасибо!
@techfixPOV7 ай бұрын
Glad it helped!
@raki_time_ Жыл бұрын
Thank you so much. You saved us a lot of money❤
@techfixPOV Жыл бұрын
I'm glad I could be of help.
@sergiojimenezcasado33005 ай бұрын
Thanks for this video, I have saved myself 125€. Dyson wanted I paid 125€ to repare this broken peace, for me it's a robery. I'll put a complain about it.
@techfixPOV5 ай бұрын
Glad it helped!
@dannyberg7053 ай бұрын
Thank you for the helpful video! Unfortunately, the display no longer turns on and the vacuum cleaner is pulsing. Could you please let me know what I might have done wrong?
@kaiserschnitselsr.9228Ай бұрын
google?
@techfixPOVАй бұрын
Make sure you have installed the small white connector correctly.
@dannywaddy913 ай бұрын
Thanks! 1 screw is hard to reach but all good
@techfixPOV3 ай бұрын
Glad it helped!
@Antares76483 ай бұрын
Thank you very much. You are the best. Perfect video 👍
@techfixPOV3 ай бұрын
Thank you too!
@1966Ally Жыл бұрын
You are a life saver, thank you for sharing your great video
@techfixPOV Жыл бұрын
Glad to be of help!
@BarbarosAlpАй бұрын
Thanks a lot for the video, I managed to fix it as well.
@techfixPOVАй бұрын
Glad it helped
@BITProductionsКүн бұрын
Thanks for this video, big help 😊
@techfixPOVКүн бұрын
Glad it was helpful!
@reeferem2643Ай бұрын
thank you, worked like a charm! Will be bookmarking this vidz for later on ;)
@techfixPOVАй бұрын
Glad it helped!
@josecg8016 Жыл бұрын
Desde Granada, España, muchas gracias! Te debo una cerveza 😊
@techfixPOV Жыл бұрын
Me alegro de haber podido ser de ayuda! :)
@sim08u7 ай бұрын
Great Vid, followed it for my V11 which was slightly different. Only problem I face now is after putting it all back together and sticking the battery in, is it turns on and stays on, from what I've read elsewhere its because i didn't push the trigger mechanism high enough or the new trigger is slightly longer - not sure. But people typically file down the black trigger button on the battery and it fixes this issue. So will have to do that.
@sys12375 ай бұрын
That has happened to me, in the end how do you fix it?
@sim08u5 ай бұрын
@@sys1237 filed down the trigger button. But I wouldn't really call this a fix tbh. Because every now and again it still sticks.
@michaeltammaro4829 ай бұрын
Excellent tutorial video. Thank you!
@techfixPOV9 ай бұрын
Glad it was helpful!
@moisescampos690 Жыл бұрын
Wow.....Perfecto, tu video es genial, muchas gracias, saludos desde España!!!
@techfixPOV Жыл бұрын
Me alegro haber podido ser de ayuda.
@moisescampos690 Жыл бұрын
@@techfixPOV gracias a tí he podido arreglar la Dyson de mi padre, y si la mía falla algún día pues también sabré arreglarla.... MUCHAS GRACIAS!!!!
@jesperrdk6 күн бұрын
Hi, thanks for a great toturial. After i changed my button, the torque brush only turns when its on boost level. On eco and med it turns 1 sec. and then stops. Do you have any clue what can curse this ? 😢 Funny thing, my wife says that it blows more than normal from the filter and if i close my hands around the holes in the filter, the brush runs, also in med and eco and when i remove hands, it changes a little in sound and brush stops 😮 do you have an idea ? Br. Jesper
@jeffgirardet53342 ай бұрын
Excellent video thank you very much
@techfixPOV2 ай бұрын
Glad it helped!
@murrkaya230510 ай бұрын
5:46 Just make sure that you removed the screw before pulling out the assembly! If not, you will end up breaking something like I did.
@techfixPOV10 ай бұрын
The screw you refer to is removed at 1:00 kzbin.info/www/bejne/nJu6i36ihdGkeacsi=FrtoZU1sR_QImwRd&t=60
@murrkaya230510 ай бұрын
You are right! I might have missed it. My bad!@@techfixPOV
@tsung138 ай бұрын
Great video but it should be noted that before I pulled out the trigger assembly at around the 5:50 mark, there was a screw that I had to take out first. At first I pulled and pulled and finally shined a flashlight inside to discover the screw! Maybe Dyson changed their design but definitely should be added to the video.
@techfixPOV8 ай бұрын
The screw you refer to is removed at 1:00 kzbin.info/www/bejne/nJu6i36ihdGkeacsi=FrtoZU1sR_QImwRd&t=60
@user-pf7eu4cv9y6 ай бұрын
Спасибо брат🤗 благодаря тебе сэкономила время на сервисе👍👍👍👍👍
@user-fv7fr3lc1w8 ай бұрын
拍得非常仔細。成功換了按鍵。
@techfixPOV8 ай бұрын
Glad it helped!
@luisdomingorojassanmartin246816 сағат бұрын
Gracias, muchas gracias por el video🎉
@techfixPOV16 сағат бұрын
Glad it helped!
@erwinkomer40063 ай бұрын
Dzięki super materiał bardzo mi pomogłeś. Pozdrawiam z polski.
@techfixPOV3 ай бұрын
Cieszę się, że było pomocne!
@rushelaronov88554 ай бұрын
Thank you very much.
@techfixPOV4 ай бұрын
You are welcome!
@puntomiron Жыл бұрын
Fantástico!!! Muchas gracias desde España!!!
@techfixPOV Жыл бұрын
Me alegro haber podido ser de ayuda.
@moranaheimspecv Жыл бұрын
Thank you! But you make it look so easy haha
@techfixPOV Жыл бұрын
Happy to help!
@horselogy2 ай бұрын
I've changed my dyson v10's trigger but when I put battery on it starts running and does not stop. I suspect that my triggers tail is longer than it should be. Do you have any suggestions?
@elenacl78619 ай бұрын
Muchas gracias!!!me ayudado mucho el video!!
@techfixPOV9 ай бұрын
Glad it was helpful!
@roswinda Жыл бұрын
Muchas gracias, lo hice bien Gracias a tu vídeo ❤
@techfixPOV Жыл бұрын
I'm glad it was helpful.
@MadelineMoloney11 ай бұрын
I followed the instructions and it works again! However I can’t get it to stop. If the battery is in it keeps running. Where did I go wrong?
@techfixPOV10 ай бұрын
I think you didn't push the trigger hard enough inside the case and the button on the battery is pressed by the button you replaced.
@andrewziem37010 ай бұрын
Did you figure this out? I'm having the same problem. I have the white panel open, and I'm trying to avoid disassembling the next part which was tricky. When the battery is in, it feels like the trigger has a good range of motion.
@melvingoh23307 ай бұрын
I had the same problem. I figured it might be the new trigger being a little bit too long, applying pressure on the switch prematurely. So I took a blade and cut off around 2mm of the edge. That worked for me.
@svenhartinger2629 Жыл бұрын
Thanks a lot for this video!
@techfixPOV Жыл бұрын
Glad it was helpful!
@sabinoliebana43785 ай бұрын
Thank you!!!!🎉🎉
@techfixPOV5 ай бұрын
You're welcome!!
@HolgerGnodtke Жыл бұрын
Bester Mann! Super Video-Vielen Dank!!!
@techfixPOV Жыл бұрын
Thanks!
@Sergey025843 ай бұрын
Спасибо за видео!
@techfixPOV3 ай бұрын
Glad it helped!
@tennentslover Жыл бұрын
Thx a lot man! Useful af
@techfixPOV Жыл бұрын
Glad to be of help!
@lyhorcish2 ай бұрын
Thank you
@techfixPOVАй бұрын
You're welcome
@amak3203 ай бұрын
I accidentally ripped the white and black wires off the board. I thought I stuffed it up but I tried putting it back to the two holes and it seems to be working and charging fine. Would you know what the two wires are for if I will have any issues later down the track?
@techfixPOV3 ай бұрын
The two wires you refer to are connected to the connector that powers the brushes. If those wires are not installed correctly, the motorized brushes will not work. So, make sure they are connected correctly in the electronic board. You just have to simply push them into the dedicated holes.
@amak3203 ай бұрын
Thank you, it’s working fine since so I must have pushed them In correctly. Phew.
@berlindoktor82Ай бұрын
Worked perfect ! 👍 thx
@techfixPOVАй бұрын
Glad it helped!
@drorbank61554 ай бұрын
Thank you so much!!!!!!! 👑👑👑
@techfixPOV4 ай бұрын
You are so welcome!
@SuperMch74 ай бұрын
The Best.
@techfixPOV4 ай бұрын
Thank you!
@belkacemrebbouh492527 күн бұрын
Thanks !
@techfixPOV15 күн бұрын
Welcome!
@EnjoyTech6929 Жыл бұрын
Hey ! Is it good to use thé little accessory that Block thé button when you use it ? Will it help not to break it ? Thank you
@techfixPOV Жыл бұрын
Hello! This is a very good question. In my opinion, the button fails due to a design issue with the button, the button having a weak area that fails when high pressure is applied repeatedly. In my opinion, using an accessory like the one you mention would help because the pressure applied to that button will be constant and, certainly, lower than those pressure spikes when the vacuum cleaner is used without such an accessory.
@EnjoyTech6929 Жыл бұрын
@@techfixPOV thank you for your answer, that makes sense !
@korbondacob6 ай бұрын
Is there a good trick to get the switch back in its position I have pushed as hard as I can and it will not pop back into place no matter what I try
@sys12375 ай бұрын
Before watching the video I had my Dayson V10 not working, now after changing the red button that had it broken, it is working all the time and does not stop. What can I do?
@techfixPOV3 ай бұрын
Carefully follow the steps from minute 7:00. You have to make sure that the trigger is fully pushed and that it is fixed with the screw. It seems that the trigger is not fully pushed and the red button permanently activates the button on the battery.
@stefano3983 Жыл бұрын
Great video! Congrats and thanks! ;-)
@techfixPOV Жыл бұрын
Thank you! I`m glad it helped!
@pianoplaynight7 ай бұрын
To everyone that put the vacuum back together and is horrified that it's not turning on - as I was - but instead only briefly shlwing three blue lines: it means you didn't plug the small white square connector back to the electronic board in properly. I suggest you go back, really push it in (it should click) and even add a nice layer of glue like it was when you opened it. Works like a charm after this!
@user-jq2uf8jq5r2 ай бұрын
Vorrei sapere perché invece non stacca più la batteria. Sarà difettoso il grilletto?
@psicoclinicamexico47602 ай бұрын
Gracias!
@techfixPOV2 ай бұрын
Glad it helped!
@ivanrudskyi36033 ай бұрын
Огромное спасибо
@techfixPOV3 ай бұрын
Glad it helped!
@yuinamiinachannel Жыл бұрын
Mine still wouldn’t work after replacing the trigger. The battery and the trigger works, yes but the vacuum doesn’t. Could I have ruined the circuit or some other part while replacing the trigger? When the filter isn’t placed and I pull the trigger, the filter light doesn’t turn on. Thank you.
@techfixPOV11 ай бұрын
What model of vacuum cleaner? Before changing the button, did it work properly (except for the button problem)? Maybe you didn't mount the small white connector with thin wires correctly.
@user-cq8no5mf6n8 ай бұрын
Всё чётко по этапно повторяя за видео можно поменять за пол часа! Но есть одно но! Последний шурупчик который внутри ручки, он падла😂 под него нужна тоненькая отвёртка звёздочка, который не во всех магазинах продеться эта кнопка продаться на озоне вместе с отвёрткой берите отвёртку сразу если нет таковой, переходники не пролезут нужна именно тоненькая отвёртка
@antoniodigregorio32619 ай бұрын
thx for the videoo!! now the speed selector doesn't work. the dyson only runs at full speed. any solutions?thx
@techfixPOV7 ай бұрын
I think you did not mount the module containing the hall sensor correctly. It is a small PCB that is mounted in the upper part near the selector button.
@valaki20588 ай бұрын
Hello! Could you give me a tip on how to prevent the trigger from breaking, eg not pushing it all the way in? 😅
@techfixPOV8 ай бұрын
Yes, it would be a good idea to try pressing the button with less pressure. Otherwise, the only option would be to replace the existing button with a model that has a stiffened area where the button frequently fails.
@Peekaboo0910 ай бұрын
I followed the video and changed the new trigger, as soon as I inserted the battery without pushing the trigger, the vacuum turns on and won’t stop. Any clue?
@techfixPOV10 ай бұрын
I think you didn't push the trigger hard enough inside the case and the button on the battery is pressed by the button you replaced.
@Braxen807 ай бұрын
How do I get the trigger part out of the handle? Do I have to do anything more than then just pull it out?
@techfixPOV7 ай бұрын
Do not forget to remove the screw that blocks the trigger. I dismantled it in the first part of the video.
@pedror.c6685 Жыл бұрын
Thanks!!! ❤
@techfixPOV Жыл бұрын
You're welcome 😊
@Sineadnichaollai3 ай бұрын
I’ve done something wrong - worked again for 5 mins and now red constant light ? Anyone know what I’ve done?
@techfixPOV3 ай бұрын
Make sure that the small white connector with red and black wires is mounted correctly (11:00). Also make sure that the two terminals fixed with screws are tight and do not come into contact with each other.
@sandrofranco55847 ай бұрын
ottimo
@techfixPOV7 ай бұрын
Glad it helped!
@irubia4 ай бұрын
Demasiado laborioso.. hay que tocar muchas piezas.
@techfixPOV3 ай бұрын
Si tiene paciencia y las herramientas adecuadas, definitivamente podrá realizar esta reparación.
@steveczupryna9720 Жыл бұрын
anyone know where the screws for the two power cables can be found if someone "ahem" misplaced them? The two silver screws at 10:45 in the video
@techfixPOV Жыл бұрын
You can use M3 screws, but they should not be longer than 7mm (thread length). Make sure you tighten them well to avoid imperfect contact and overheating of the connectors.
@user-lj7iq3ro4l Жыл бұрын
Это было великолепно!
@techfixPOV Жыл бұрын
Спасибо!
@user-kd2ow7pb1c11 ай бұрын
Просчет конструкторов Dyson. Массовые поломки этих кнопок. Кнопка многофункциональная, нажал - вкл, еще раз нажал - выкл. Кнопка слабо усилена. Чтобы до нее добраться нужно разобрать весь пылесос, еще и двумя типа бит. В 10 модели еще с сделана заливка кампаундом печатной платы и контактов( в 11 серии убрали заливку). Есть три типа кнопок в продаже : простая, усиленная с али, и родная. Я бы предьявил заводу дайсон претензию за столь дилетанский подход к конструкции. Сидят теоретики , рисуют на компах. Их пальчики приспособлены только , чтобы буквы на тачскрине телефона нажимать.
@Sergey025843 ай бұрын
Кнопка сломалась после 4 лет использования, на озоне за 600 руб заказал. В сервисе 3к сказали. То и то норм вроде. Но самое интересное, что пиндосам заряжают за ремонт по 200$ + судя по комментам)
@Elliotscootsalot Жыл бұрын
Wow! Dyson don’t make it easy to replace that part!!!! 😳
@techfixPOV Жыл бұрын
That's right, it's not the easiest thing to do. But with a lot of patience and the necessary tools it is not impossible.
@deni299098 ай бұрын
СПАСИБО 🙏
@techfixPOV8 ай бұрын
Glad it helped!
@eyul.Sky_eylul Жыл бұрын
Neden motorun üstü plastik kaplı? Ben kendi motorumu açtım bende de var , ben daha önce tamir edildiğini düşündüm bu yüzden daha fazla devam edemedim.
@techfixPOV Жыл бұрын
The role of that plastic is to protect the electronic board from dust, water and vibrations.
@kollianaestrada7410 Жыл бұрын
Bonjour, J’ai fait exactement ce qui est montré sur la vidéo, mon bouton est réparé mais l’appareil ne démarre plus. Quand j’appuie sur le bouton de démarrage la Batterie clignote bleu 10 fois. Pourriez vous m’aider ? Merci beaucoup
@techfixPOV Жыл бұрын
Bonjour, Your issue (battery led blinks 10 times) can be caused by these reasons: 1. you forgot to plug the small connector that powers up the mainboard: kzbin.info/www/bejne/nJu6i36ihdGkeac 2. maybe the same connector got damaged somehow or is not properly connected. You can check if the mainboard is powered up by pressing the button placed on the display. If the display shows nothing, probably there is a problem with the connector. 3. the mainboard is damaged
@kollianaestrada7410 Жыл бұрын
@@techfixPOV La carte mère doit donc être endommagé .. parce que le connecteur est bien branché et mon écran s’allume bien, seulement le moteur ne démarre pas.
@techfixPOV Жыл бұрын
Before replacing the button, did it work fine? I mean, are you sure that only the button was broken? Because if it worked fine before, maybe something happened at reassembly. Maybe the battery terminals are not tight enough on the mainboard or are getting in touch with each other.
@kollianaestrada7410 Жыл бұрын
@@techfixPOV oui l’aspirateur fonctionnait avant le remplacement du bouton, mais comme le bouton était cassé il avait du mal à démarrer, une fois que j’ai remplacé le bouton, j’ai pu voir que ça fonctionnait car dès que j’appuie sur le bouton la batterie clignote bleu. Je pense effectivement que c’est lors du remontage que quelques choses c’est passé. Mais j’ai tout démonter et remonter plusieurs fois et je n’arrive pas à trouvé mon erreur, j’ai l’impression de tout avoir bien remonté et pourtant il doit y avoir une erreur. Merci beaucoup pour tes réponses rapides en tout cas !
@user-wc8ce1xi5o7 ай бұрын
Круто 👍👍
@techfixPOV7 ай бұрын
Thanks!
@pablopmdodi3 ай бұрын
¡Gracias!
@pablopmdodi3 ай бұрын
Muchas gracias, me has ahorrado 109 euros!!
@techfixPOV3 ай бұрын
Thanks for the reward! I'm glad the video was helpful!
@juneburns1565 Жыл бұрын
Not sure I could do this !!
@techfixPOV Жыл бұрын
Sure you can! Make sure you have the new button, a plier and two screwdrivers (phillips, torx t8).
@Ak750004 сағат бұрын
Y’a 1 millions de vis de quoi construire un avion ✈️ 😂
This device is such junk 😅..... I replaced the switch on mine I've never held anything so cheap.
@guillermoenki1069 Жыл бұрын
The thing that you take out at 2:39 ( with black and red wire) broke. The plastic white where the wires go. Now I have the wires free. Is there anyway to fix it? Thank you.
@techfixPOV Жыл бұрын
Try to solder both wires directly to the motherboard.
@jesperrdk6 күн бұрын
Hi, thanks for a great toturial. After i changed my button, the torque brush only turns when its on boost level. On eco and med it turns 1 sec. and then stops. Do you have any clue what can curse this ? 😢 Funny thing, my wife says that it blows more than normal from the filter and if i close my hands around the holes in the filter, the brush runs and when i remove hands, it changes a little in sound and brush stops 😮 do you have an idea ? Br. Jesper