Mine pulses with everything clean on high. I want to see how to bypass the trip~

Nice video! Is it safe to assume the new chip got it working?

next time to remove back part install filter and use it as handle, don't use screwdriver, it lefts damages on parts, use thin knife if necessary

Nice video music is annoying

Same issue here power switch worked intermittent. Morons at dyson half screwing the screw and melted the plastic. Thanks!

Hi, I don't have power on the vacuum cleaner brush (dyson v15 detected absolut). I've already changed the mosfet, but it has no effect. What can be done?

Solved my problem as well, thanks for sharing. Very helpful👍🏼👍🏼👍🏼❤️

Thanks for the video. I fixed my devive ❤

Hello, you might find this helpful. I had a similar problem with my V12, after starting, it would turn off immediately. Only after 5-6 attempts of starting and stopping would it finally run continuously. The issue was with the three capacitors on the motor board. On mine, the capacitors are marked as 1N2 270 VHC. I discovered that they are 270 µF, 35 V hybrid capacitors. I replaced them six months ago, and I haven’t had any issues since then.

Muchas gracias! Me ha servido para reparar mi V10

Hi! I'm subscribed to your channel, I read that many slim v12s turn off after a few seconds. It happened with mine too. Can you make a video or tell us the problem?

Thank you sir I love your video explanation is great but mine is brand new and it stopped working I find them cheap for the price and needs a lot of care !!

Hi! I'm subscribed to your channel, I read that many slim v12s turn off after a few seconds. It happened with mine too. Can you make a video or tell us the problem?

Hi! I'm subscribed to your channel, I read that many slim v12s turn off after a few seconds. It happened with mine too. Can you make a video or tell us the problem?

Thanks!

VERY helpful video in walking through the disassembly steps. What I discovered may be important to other viewers. The wires looked intact, yet the motor would die after 5-10 seconds. I discovered that the grey wire coming from the motor had likely internally broken slightly just as it entered the spade connector. So it acted like one tiny strand of wire was initially conducting but as it overheated it pulled apart. The answer was to "flood" a little solder from the connector back up the wire maybe 1/20th inch by heating the connector enough with a pointed soldering iron. Problem fixed. But not an obvious one. Thanks for this great video.

Thanks! I was able to replace the broken trigger by myself! The hardest part is to find a T8 tool)

Ps Great video 😁

Anyone else have tears running down their face at the end? Just the sound of the Tuba to the extended zoom shot of the rust! Alas... Mine too has succumb to that dastardly rust! 😢

my device stops after 5 seconds of running. What could be the problem?

January 2025. Thanks, just completed the replacement in 90 minutes following this. No problem, and my Dyson V10 didn’t have the silicon protection on the board. The plastic trigger was broken in such a way it prevented a direct pull-out, so I had to break and prise it out through the trigger hole. Replaced with a steel version, a little smear of Vaseline helped get the new trigger over the pins.

What should I do if a red light comes on when I use a magnet?

Today, i washed mine and drying now. I saw that a gasket around 7 pound. I hope you make a video about only changing gasket.

Grazie x aver condiviso 😉👍💯

Soldering is a horrible fix. The copper wires will work harden and break at the solder joint. Only a new wire or a mechanical splice (butt connector, twist wires etc) will truly fix it. It WILL break again.

Can you tell me what’s those wire function, I already sent to Dyson and repaired, so the motor Dyson says broken is at my home, I want to test it,because I think it isn’t broken,I know the power pin,but I do not know what’s the red and white wire, I need a teacher!

Thanks bro!!!!!!! DIY forever!!

This still works.

We opened our Xiaomi vacuum cleaner and discovered its poor design, especially the internal filter for the fan that discharges air to the outside, as it was made in a way that ensures that the motor malfunctions after a measured period and thus leads to damage to the main board.

Comprehensive video but the music is annoying

Merci beaucoup 🙏

Could you list the tools needed for this? I'll probably need to buy a couple of them. Thanks!

This is a joke , had many hoovers in my life , but to spend over 200 pounds on this one and fix like that i crazy , i just scrap mine and buy new one , never dyson again

How do you replace the blue hose on the Dyson V15 laser cleaning head? I can't find a replacement hose for the laser head or any videos or instructions on how to do it. It's frustrating.

What a goat !

hi where you located

The old trigger piece did not look bad but the pivot holes were worn and elongated a very little bit, but it fixed the problem. Can't believe it was designed to be so critical..

I have the Dyson 7 animal. My bar will spin freely so I know the shaft is not stuck. It will not spin when powered though. The Minnie head works fine though. Do you know want the issue is? Some say to clean all electrical ports going back to the main vacuum motor. But if the Minnie will spin and work fine could that be the issue?

Thanks but I know because I’m here to remember that for my hp04

Fantastic teardown. Really helped me clean mine. Thank you. ❤

Where can I buy one new motor from ?

Merci beaucoup pour ce tuto ! Il m'a bien aidé à changer la gâchette de mon V10 ! 👍👍👍👍👍👍👍

I’m interested in seeing the part where you take the gold plastic piece off the motor body there’s some purple foam in between the two gold pieces. How do I repair that purple foam seal? Mine is deteriorating and I could feel air blowing through. You skipped that part in your video.

Muchas gracias por tu video, ha sido de gran ayuda. Saludos desde España

Je. l'ai acheté il y'a deux ans une fois la garantie passée ce lui ci tombe en panne ,ça réparation coûte un bras et bien entendu son prix d'achat aussi un conseil passez votre chemin .il est excessivement cher, vous allez payer juste la marque et cerise sur le gâteau il aspire moyen. rien de phénoménal !

First of all, I apologize for my poor English. I have a similar problem with my V15. It works like this and then stops, but after doing this 3-4 times, it continues to work without any problems. Then I stop the machine again and take a 1-minute break and it works without any problems again. But if I take a 15-20-minute break and do not start the machine, it starts to have the same problem again. So I think the machine returns to normal after working and warming up a little. If we take a break and let the machine cool down, the problem starts again. What do you think could be the source of this problem? I have been researching for 1 year but I could not find a solution.

Hello. Could you please make a video how to fix the Dyson v11 motor that turn on 1 second then stops ? ( motor issue not pcb board issue)

Hello, Could you help me? I have a similar problem with Dyson v10, that the motor does not turn because there is no power, how could I check that it is the mosfet that is failing

Podrias ayudarme? tengo un problema similar con Dyson v10 animal, que el motor no gira porque no llega alimentación, como podria comprobar que sea el mosfet lo que esta fallando

Wow! You are a genius. My vac smells like a wet dog. The smell is coming from the metal screen on my Dyson 15. I’m quite shocked that all the dust gets so deep into the vacuum.