How to Replace Engine Mount 2006-2013 Chevy Impala

Buy Now!
New Engine Mount from 1AAuto.com 1aau.to/ia/1AEMT00254
This video shows you how to install a new engine mount on your 2006-2013 Chevy Impala. A shaking or vibrating engine, or bucking when changing gears are signs of worn engine mounts.
This process should be similar on the following vehicles:
2006 Chevrolet Impala
2007 Chevrolet Impala
2008 Chevrolet Impala
2009 Chevrolet Impala
2010 Chevrolet Impala
2011 Chevrolet Impala
2012 Chevrolet Impala
2013 Chevrolet Impala
Tools you will need:
• 15mm Socket 1aau.to/oa/1AXAA00015
• Ratchet 1aau.to/oa/1AXAA00016
• Socket Driver
• Swivel
• Torque Wrench 1aau.to/ob/1AXAA00044
• Block of Wood
• Paper Towels 1aau.to/oa/1AXSS00035
• Floor Jack 1aau.to/oa/1AXAA00068
• Jack Stands 1aau.to/oa/1AXAA00065
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@casdoitall5645]

I just changed out my mom's engine and trans mount. All thanks to you guy's videos.

[@casdoitall5645]

Excellent video, I didn't know Bob Ross was also a mechanic!😂😂

[@user-nu6rx5wi4k]

Do you have to loosen the upper motor mount to raise the motor to replace the hydraulic motor mount

[@barrysauce]

If these bolts are not properly tightened would it cause vibrations during hard acceleration and also make the engine not run as smooth?

[@tsfyootwiin]

Just ordered mimes today, can't wait to fix it on my 2010 Impala

[@sumbamotor]

Thank you so much

[@adriannavarro4255]

I replaced all mounts on my 2010 Impala, but it seems to kick/jerk when i shift from parking to reverse, at times it kicks pretty hard, anyone knows what it could be? A transmission solenoid maybe?

[@capadon77]

How many lower engine are on this vehicle?

[@travisbutler4365]

How many mounts are they

[@brianszanyi5538]

I just did the job I did it from the I took the passenger tire off I would suggest that you cut away the bad rubber with a steak knife so you can use your socket better cut away the bad

[@drjoeset]

Never tighten bolts until all bolts are in place, it makes life a lot easier, Now as far as the nuts on the bracket you have no choice because you won't be able to reach them later

[@RCLBWD]

Bro you gotta show us where the bolt is at, you got the camera zoomed in so far you can’t tell where it is

[@tsfyootwiin]

Its literally under the crankshaft, can't miss it

[@doc_ineeda_win5834]

did you have to losen or take of top mount to let it lift enough?

[@tsfyootwiin]

Don't really have to, unless you wanna make extra work.

[@JimTMcDaniels1]

I say wrap-cover that new mount, before installing, in some discarded durable plastic bag/packaging and use some clear box tape to secure around it. This way, petroleum oils which leak out of the seals of our old engines won’t be able to drip on and degrade the edpm rubber mount, causing another failure! Take care

[@cecilwebb2277]

Poor camera angles on this 1. Couldn't tell what you were doing and where.

[@thewildbros1044]

U don't curse enough...lol.

[@xx_tyrome_xx8288]

If your not a mechanic already you have a tough time this video