How to Replace Front Brakes 2012-2017 Toyota Camry

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@Majinjef2099]

There's noway the mechanic at the shop does that thorough of a job.

[@jkgoet01]

Best brake change instruction video ever made! 👏👏👏 Very thorough, no fluff, great explanations of the reason for each step, perfect!... I'm very comfortable changing brakes and didn't need to watch this but couldn't help but keep watching.

[@jonathanjohnson9192]

A solid, clean video that explained everything for a first-timer's success. These $89 brakes "Autospecialty KOE3053 1-Click OE Replacement Brake Kit" plus a few other mentioned supplies from the local auto store is a total of ~$130. Contrast that with a local mechanic and a dealer who both quoted ~$600 for the job. Tips: - Invest in a quality lift jack and stands, not the dangerous and unstable one in your trunk. - C-clamp vise grips will effectively squeeze the caliper piston. - Use two bolts that you can screw into the existing wheel bearing holes that are specifically designated to pop off the old rotor in less than a minute. No hammering or wheel pull tool is needed.

[@sotechy92]

Such a detailed/ quick/ and very accurate explanation of the front rotor/ brake pad install. Thank you so much!

[@JBRion22]

T Super thorough, thanks for including the torque specs

[@sgarrett36]

Great, detailed video, and at only 6.5 minutes!

[@REDACTED-1]

What a great video. Right to the point and thorough. Thanks for uploading.

[@Nwwoods]

Excellent information… thank you

[@user-oz3bu3qz5t]

Nice! Would’ve been allot better if you mentioned the socket sizes too when removing the bolts though

[@toppo3667]

Good quality work and video. Thank you!

[@azvtxrider]

Direct and to the point. Thank you for this.

[@weeshock3480]

Just found out after an hour of frustration, and calling every parts dealer in town, the retaining bolts on the calipers also compress. I thought my pads were too thick, and everyone said that I needed to compress the piston more.

[@miketobin2324]

Can the brake system be damaged during the piston retraction if the bleed valve isn't opened first? Is there any check valves in the ABS that might be damaged with fluid going against the grain?

[@traderboi2662]

Man loves his job!

[@baby19981997]

What happens if you put the wrong bolt pin with the rubber seal?

[@imnot2398]

Nice job and cleane.

[@khoivuong1537]

Good job thanks

[@c.h.r.i.s2253]

Every Camry front brake video has the wear indicators on different ends on the outer and inner Most have both on top

[@napsterbater]

I just wish they were back on the pads permanently like they used to be. But I just did my car and didn't realize they were going to be separate and I ended up putting them both back on the bottom It doesn't look like it matters but hopefully it doesn't.

[@digitalcamaraderie5685]

I only added top pad separater. Didnt had bottom for one side amd othee i lost it

[@Shmilio]

I wish this guy would work on my car lol

[@ElroyBeezley]

Tell us what size bolts are.

[@aateel71]

Nice job but I would never push brake fluid back up into the system. It’s simple to just break open the bleed screw.

[@TRQ]

+aateel71 Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@REDACTED-1]

Yeah. Except it’s completely fine. The system is sealed. Anything in the system is already in the system. The piston being seated again isn’t introducing anything foreign to the hydraulics.

[@firetools1]

Never squeeze the piston back using that tool. Use a caliper tool or put the old pad back in and use a C clamp. Also went a little too far with the grease, no need to coat the outer pad and caliper piston.

[@frederickflores8152]

Be great if you guys listed the size sockets

[@Menudo-boy]

I have replaced pads and rotors 3 times. And my breaks squake

[@jaysofresh3482]

You don't have to bleed the brake lines?

[@zakac17]

Thanks!

[@aminudan5748]

Please future video said the bolt size it helps...

[@TRQ]

+Aminu Dan Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

[@bantuerverh607]

You didnt say nothing about doing rotors

[@fmart3617]

Feel like doing mine? I'll pay.

[@traevonbassett9654]

Verhicle