How to Replace Front Bump Stop 1999-2007 Chevy Silverado

Buy Now!
New Control Arm Bump Stop from 1AAuto.com 1aau.to/ia/DMSMX00029
Rubber bump stops prevent suspension components from slamming against the frame or body of the vehicle when the shocks or struts bottom out. Over time the rubber can harden or break down, making it less effective, or causing the bump stop to fall out, This video shows you how to install a new front bump stop on your 1999-2007 Chevy Silverado.
• Check here for more videos on the 1999-2007 Chevy Silverado: • Chevy Silverado 1999-2...
This process should be similar on the following vehicles:
1999 Chevrolet Silverado 1500
2000 Chevrolet Silverado 1500
2001 Chevrolet Silverado 1500
2002 Chevrolet Silverado 1500
2003 Chevrolet Silverado 1500
2004 Chevrolet Silverado 1500
2005 Chevrolet Silverado 1500
2006 Chevrolet Silverado 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• Pry Bar 1aau.to/oa/1AXAA00020
• 22mm Socket 1aau.to/oa/1AXAA00266
• Torque Wrench 1aau.to/oa/1AXAA00044
• Gloves 1aau.to/oa/1AXSS00048
• Rust Penetrant
• Safety Glasses 1aau.to/oa/1AXAA00343
• Floor Jack 1aau.to/oa/1AXAA00068
• Hammer 1aau.to/oa/1AXAA00091
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Chevy Silverado 1999-2007 1st Gen: • Chevy Silverado 1999-2...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@ricardovelasco1365]

Thanks for the info!

[@Mike.715]

Nicely done 👍 I liked how you went over different options/ways to get it in if someone was having a problem getting the new ones in

[@rogermerritt6470]

Do the front bumpers normally rest on the control arms? I have no clearance on my 2002 Suburban. Getting a rough ride.

[@WayOffGrid]

What are the cups which hold the bump stop connected to? Are they welded?

[@ricardoflores403]

Where did you buy those bump stop? I have a trailblazer and it has the same ones as those i look on line but they have different ones even though it says it fits my truck.

[@elevatedinnature]

Is this a 1500? Because I have a 2004 with the odd shaped rectangular block, I bought both bc I wasn’t sure which one it needed do to it being rotted off

[@randyowens3947]

I have 2001 S-10 Blazer that needs that in front.Will it be like that?

[@artsisland1683]

This procedure is also applicable to the Ford F350, same vintage years. 👍

[@chevyss18]

Are they the same size for the rear?

[@TRQ]

+JayR Thanks for watching! No rears would be a different size.

[@leorickt.9604]

how do you know if the bump stops need replacing?

[@JohnKieken]

Usually the old ones are dried up, broken, and falling apart.

[@maddmavic]

If the lil cup that holds them comes off how do u fix that

[@DoomedandFuzzed]

With a saws all or angle grinder. I had to do my fronts they rusted out you can buy the whole assembly with the nut and bolt you are better off in the long run.

[@WayOffGrid]

Mine appeared to be plug welded and came off. Not bolted!

[@fluoridaman2332]

Remove the rust using a wire wheel die grinder and it will slide right on.

[@scott2228]

I have a 2009 GMC Sierra and I can’t find the Bump Stop online anywhere. Everything I find says it doesn’t fit. Even though the pic looks correct. 🤷‍♂️🤷‍♂️🤷‍♂️

[@DoomedandFuzzed]

They are universal with a Silverado 1A Auto is where I got my front and rear.

[@johnharrison5098]

why not take a wire brush to the inside? little tlc goes a long way