How to Replace Front Drivers Side CV Axle 02-06 Nissan Altima

Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ia/1AAC...
1A Auto shows you how to repair, install, fix, change or replace broken, worn, or vibrating CV axles. This video is applicable to the 02, 03, 04, 05, 06 Nissan Altima.
This process should be similar on the following vehicles:
2002 Nissan Altima
2003 Nissan Altima
2004 Nissan Altima
2005 Nissan Altima
2006 Nissan Altima
🔧 List of tools used:
• Pry Bar 1aau.to/oER/1AX...
• 22mm Wrench
• 21mm Socket 1aau.to/oVD/1AX...
• 22mm Socket 1aau.to/oi6/1AX...
• 32mm Socket 1aau.to/obz/1AA...
• Ball Joint Press
• Dead Blow Hammer 1aau.to/oHL/1AX...
• Needle nose pliers 1aau.to/ovv/1AX...
• Needle nose pliers 1aau.to/ovv/1AX...
• Side Cutters
• 1/2 Inch Breaker Bar 1aau.to/ooq/1AX...
• Ratchet 1aau.to/oa5R/1A...
• Socket Extensions 1aau.to/oaRw/1A...
• Torque Wrench 1aau.to/oadS/1A...
• Cloth Rags 1aau.to/oux/1AX...
• Paper Towels 1aau.to/oux/1AX...
• Rust Penetrant
• Drain Pan 1aau.to/orw/1AX...
• Floor Jack 1aau.to/oKZ/1AX...
• Jack Stands 1aau.to/oIp/1AX...
• Rubber Mallet 1aau.to/oer/1AX...
Subscribe: / @1aauto
Check out our playlist:
Nissan Altima 2002-2006 3rd gen: • Nissan Altima 2002-200...
CV Axle Replacement: • CV Axle Replacement
For More Info visit us at 1aau.to/h/btd/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@K1NGPUFF]

He used ratchets!!! First pro yt mechanic using rathets not power tools! HIGHLY RESPECTED❤

[@masa.aviator]

I own 2003 Nissan Altima 2.5S. When you try to remove old CV Axle from the transmission, I recommend you to use 15" flat pry bar rather than pry bar. There is a gap about 1/4 inch between the wall of transmission and CV Axle and it may be difficult to remove it with pry bar since there is not much room for leverage. I bought a slide hammer with axle puller adapter but it required a wider size axle puller adapter so I couldn't use it at all. By the way, thanks to 1A Auto for the video series. You guys saved me a lot of money for repair cost!

[@1AAuto]

+Masanori Saito Thanks for the feedback!

[@gimlidragwayfan]

You guys always have great how to videos,,however I like the option of removing strut bolts tie rod end and brake hose clip and abs clip ,,removing cotter pin on ball joint always a pain

[@1AAuto]

+red river fisher Ches Thanks for the feedback!

[@johnnysins4158]

My man did everything with ratchets and wrenches instead of power tools. Dude is legit.

[@1AAuto]

+@johnnysins4158 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@69ChevyGarage]

Here is a tip so you won't screw up like I did. Look at how he's separating the ball joint with the tool at 5:02. I did that the top slipped off and damaged some of the threads. That was almost a disaster. Leave the nut on the top to protect the treads. So when I tried putting the nut back on, the blot turned too. I had to place a jack at the point of the control arm bolt to hold it then I was able to thread the nut on by force.

[@1AAuto]

+Giuseppe Benvenuto Thanks for the tip!

[@michaelsans8167]

Great work you make it look easy it’s not I know

[@1AAuto]

+Michael Sans Thanks for the feedback!

[@69ChevyGarage]

So mix matching an non-ABS axle with an ABS axle won't give me any problems? I am having a hard time finding a non-ABS axle for my 2006.

[@tristanprice1830]

Yup no problems

[@Smile-uwokeup-2day]

Great info here my car is 2011 Elantra my passenger side cv joint needs to be replaced

[@AvengerHawkeye95]

Does this also work with the passenger side??

[@arturohernandez3872]

You do not need to remove the ball joint bro all you need is to release the caliper that will do the trick I do it like that.

[@skylabboston6213]

Remove caliper?

[@kamilbmx]

I couldn't get the pry bar in the ideal position to undo the clip inside the transmission. I ended up using a crowbar and placed it between the wheel well and the caliper. That allowed me to get the right amount of leverage to pull it apart. I hope this helps somebody

[@1AAuto]

+@kamilbmx Thanks for the feedback!

[@69ChevyGarage]

How different is the passenger side? Longer axle.

[@chuimn8]

My Axel is stuck what other options I have to pull it out????

[@tannerschwindt9684]

thank you simple repair just buy a ball joint separator save u a headache

[@meTimetraveler]

I WISH I HAD A LIFT. I always wondered if Nissan ABS CV axles were interchangeable with Non ABS CV Axels.

[@rsice]

how would one go about getting out the axle where it meets the transmission if inside the boot has disconnected pretty much i cant seem to get a pry bar between the back of the axle and the transmission any suggestions? i tried to grab the axle and pull by hand and its not gonna be enough stength to get it over the surclip

[@jorgepalomera6527]

Hi! Mike, I assume you do what I will ask but just making sure. for doing your self parts do you offer warranty?

[@tonya3570]

I have an 09 Altima. Will CVT fluid or transmission oil come out when changing the axel from both sides?

[@bryanmac4583]

Can you guys do a video on how to replace the axle seals

[@LeoMartinez-fe6jz]

Gracias por su video amigo

[@1AAuto]

+Leo Martinez Thanks for checking us out! 1AAuto.com

[@tanyahill3347]

Is it better to change the whole axle if it's just the CV joint needs to change or just change the CV joint alone

[@jaysoncolbert6187]

U can't change just the CV joint, they don't sell them like that. An Axle has 2 CV joints so if any going wrong u replace the axle. I'm in same boat as u and just recently learned

[@bubaba8938]

On the right side the axle is longer..I have a sound comming from the middle part.Not sure how it's called a nut? Can that be bought,changed separtly oŕ the whole right axle?

[@TheKidAustin09]

Please make a video on how to replace front cv axels on Infiniti G35X

[@roadstar499]

It this 4 cyl or 6 cl...? What year?

[@jimmymolinaro7554]

What size (lbs) was that dead blow hammer you used?

[@Andrew-yw8vz]

Same process for the passenger side???

[@1AAuto]

+Andrew Chrisos The steps may vary slightly but the basic installation will be the same for this vehicle. +1A Auto

[@Andrew-yw8vz]

Would it be possible for you guys to do a passenger side video? You are the best guys out there for these videos

[@1AAuto]

We're always cycling through cars filming hundreds of common repairs for common vehicles every month. We'll add this to our list of repairs to film. Check back again and hopefully we'll have it soon. +Andrew Chrisos

[@Andrew-yw8vz]

Thank you so much! The passenger side is a little different. It has a carrier bearing, and I think I even messed the alignment up putting the new one in, so it would be awesome to be able to see the most professional way to do it

[@That_Guy_Miggy]

I had to change my dads 2006 2.5s model, thing is the passenger cv axle ended getting stuck. My dads been needing a new axle anyway since it’s never been changed after 14 years! Problem is we can’t break the axle nut loose and I can’t get the tire on either since the shock isn’t mounted in. Again the axle is stuck but I some advice on getting it loose without the tire on.😤 please help!

[@1AAuto]

+Miguel Bernabe Have you tried PB Blaster? There are lots of forums online discussing how people got stuck axle nuts off from impact guns to sledge hammers. Good luck!

[@nomethodjustmadness6323]

Great video. Greatly appreciate it

[@1AAuto]

Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/2002-06-nissan-altima-cv-axle-shaft/i/1aacv00214?KZbin&CTA+Comment&Z3YGZBi1c-0 +BigBadda Boom

[@jonlee2186]

Nice video, Thanks for explaining the process. Honestly though, most of us common folks don't have the luxury of a "vehicle host/lift" . Most of us are regulated to lowly floor jack. Popping out the axle from the trans axle can be a real bitch. I've watched a burly mechanic pry it out of a Maxima and he struggled a bit before it popped out. And trans fluid kinda shot out too. This was an older Maxima , so maybe they made it easier on the Altima. But trying to pop out the axle while laying on your back , on the floor with limited space to angle the pry bar can be f king Hell. And I ain't no prim a Donna. But thanks for the video.

[@MrPami9899]

Why did you replace it ?it look fine

[@1AAuto]

+STEEVE DAVID Nicolas The video is intended to show our viewers on how to replace their axles.

[@lowlifespore8993]

My cv axle bolt won’t come off... even with heat... it’s too tight. What do I do?

[@UMAIRISTA]

Can axels can cause vibration in car while driving?? I mean it will shake?

[@1AAuto]

+Umair Rocky Uneven or bent axles are another common cause of car vibration. ... If this happens, you'll feel your car start to “jostle” as you drive - and this vibration will usually increase in intensity as you drive faster. It's also possible that your driveshaft is damaged.

[@antifekaantifeka1808]

How much time to do that Job?

[@10krms8]

Is these a v6 i nee to do that to my 05 maxima automatic 5 speed any tips will help alot thanks

[@1AAuto]

This is for a L4 engine on an automatic Altima. The steps would not be the same for your V6 manual. We will keep this in mind for future videos! Thanks for watching! +10k Rms

[@michaelburke7978]

Are CV Axles transmission specific, or are they universal for both auto and manuals?

[@1AAuto]

+Michael Burke The part shown in the video is only for automatic transmission models. I would double check the part listing prior to ordering as it will always say if there are other specifications that you need to match to your vehicle. Thanks for watching!

[@davidbarlow7955]

both side same length??

[@Sroor2023]

How do you remove circlip from transmission 😅

[@tannerschwindt9684]

pop it like it's hot

[@matthewlee4303]

Would this process be the same for a 05 maxima?.

[@1AAuto]

It may be similar to this video. Thanks for checking us out! +Sir Lee

[@rrpo811]

This video is an insult to reality.

[@jacob14redisawesome34]

If only it was this easy in reality.

[@andreabuan4137]

would that throw the car out of alignment when you replace cv axle

[@1AAuto]

+Andrea Buan Since The steering knuckle has to be disconnected to make the repair, it may be a good idea to have the vehicle aligned after performing the repair. 1aauto.com

[@SuperRobertHayes]

Is this the same process for the back drivers side? I’ve been trying to look up rear driver side cv axle on your website and haven’t found anything. I’m assuming the front driver side axle is the same as the driver side rear?

[@1AAuto]

Thanks for checking us out! The rear axles are different parts than the ones for the front. +Robert Hayes

[@SuperRobertHayes]

1A Auto Parts cool thanks so much, after doing some research I realized how dumb my comment is haha

[@jorgemartinez8373]

What can happen if the clip on the end of the axel doesn't go all the way inn?

[@1AAuto]

+jorge martinez It may slip out on you.

[@jorgemartinez8373]

1A Auto Parts Oh ok...I appreciate your help

[@jaysoncolbert6187]

lol funny question. I once repaired an Axle and then realized....I didn't even put the new axle in.....jk I wastd both our time

[@FreshKicks4545]

Would it help on a 99 Altima?

[@1AAuto]

+Angel T. Thank you for checking us out. You may be able to use some of the steps shown, but the 1999 model uses a different part and the sizing of hardware may be different. 1aauto.com

[@jesselopez-gonzalez8999]

What size would i need for the ball joint separator tool?

[@tannerschwindt9684]

@@jesselopez-gonzalez8999 universal

[@bryanmac4583]

What was wrong with the old one

[@PR4470]

Sometimes the rubber boots on the axle wear out and dries out the grease then it starts making a clicking sound whenever you turn the steering wheel to turn.

[@profzvezdochkin5739]

"Driver's side".. Isn't it much easier and precise to say LEFT side? Who cares, what side they drive on in America, since BEST cars are made by Japan anyway)) Those yanks always surprise me with their weird mentality)) Driver's side! Give me a break))

[@jaysoncolbert6187]

Wanka u are

[@ramonsantiago2098]

Tall pipes nissan altima 2001

[@ramonsantiago2098]

Ok thanks

[@ramonsantiago2098]

Moflert tall pipe nissan altima 2001

[@ramonsantiago2098]

Auto pats