How to Replace Front Forward Subframe Bushing 2008-2013 Nissan Rogue

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@chrisgulotta3533]

Thank you. My front bushings were completely ripped. There was a loud clunk noise as the vehicle either accelerated or slowed. To remove the old bushing shells, I heated the tube for about 2 min and used a hammer and chisel (big screwdriver) to hit all around the sleeve. Each bushing was about 7 min to remove. To install, I did not have the bushing install kit. You might be able to rent it from an auto parts store. Whatever you do, Don't try to pound it in with a hammer. At about the 8 min mark of the vid, you can see that technician cut a chamfer (is that the right word?) to get the bushing started. I cheated and since the subframe was out of the car, I took it to the shop and they installed for $50. Working in the driveway I used a jack to lift the subframe into place. This is a very helpful video. The most valuable part, for me, is the torque settings. All together, this was a $90 repair. Plan you work space, time and tools. This can easily be done in 4 hrs (hiccups and corrosion pending)

[@Felrock12]

Tomorrow, I'm fixing my 2009 sentra subframe bushings and this video is making me very confident in what I need to do to replace it myself. Basically the same parts as a 2009 rogue since it's the same engine and transmission as in a sentra from the same year. And my cradle condition is very similar to the one in this video. Front forward bushings are shut and almost non-existent, and the bolts have the same amount of rust on them. I must say, you're pretty confident in taking those off without penetrating fluid first, good job for not having destroyed any bolts. I hope my repairs will be as simple as this video shows.

[@kingvenomc1447]

Some of the best instructionals on the tube

[@kalani4471]

a lotta rust on the frame, i guess you've determined the vehicle is still safe. thanks for the lesson.

[@nodnarbuho5789]

7:58 do you need the bushing installation tool? can you just whack it with a rubber mallet?

[@TheGhost-gx5vd]

I really enjoyed watching this excellent how you show how it should be done

[@johandevilliers756]

Thank you for a very well descriptive video. Ill be doing mine ,on the weekend.

[@michaelpatton5012]

This is my second time asking about where can I get the sub frame bushing install tool. You should show it without asking. O no you show were to buy your bushing

[@LionzDen4]

Where did you get the installation tool?

[@ced-one374]

Great video !! Can I do this job with 4 floor jacks?

[@franciscojavierfloressilva4197]

Thanks, very helpfull, Is ir absolutely necesary to removevthe lower ballboint?

[@michaelpatton5012]

Where can I get the sub frame bushing in stalling tool

[@olenaerhardt7725]

May I know the name of the Bushing Removal Tool used in this film? Actually it was used for the installation of the new bushing. Thank you.

[@cesareomiranda4485]

Thank you so much,great video⭐⭐⭐⭐⭐

[@kimberlyarmstrong4641]

Approximately how long does this job take once it’s in the air? I’m assuming this has been edited for time. Nissan wants to charge me for 8 hours. Thanks so much!

[@oludayoadeoye519]

where’s your workshop located please? I have same suv with same issues

[@TheSaabsaab]

The amount of rust I would just replace the whole subframe.

[@Duzzii_]

What is the took called to press the bushings in

[@gottosahani7571]

Thanks for the video It was very helpful

[@Dylan-tf7ru]

Where can I get the tool to remove them and what is it called?

[@MargieBKeith]

Is this called H beam bushings too?

[@cawsticky1322]

And repeat in 12months time, or 8 months in my case... OR buy poly bushes from PS Bushings in south africa and fit and forget :) the OEM type bushes aren't branded and it's impossible to tell the quality, I got mine from E bay and they didn't last, it's such a big job go for the PSB (problem solving bushings) one, you won't regret it :)

[@chrisbaker8816]

Great video

[@joonyaboy]

Anyone know where to get the tool?

[@LuisMartinez-km9gi]

You didn't show how you pushed the bushings into the subframe.

[@josefranciscoesquertalaman3827]

Like 🎉

[@shottaz2003]

He did not even install the rubber for the bottom of the bushing. What a quack. That customer is gonna be back for noises and u spoiled their good bushings. This is a poor video. Disliked 👎

[@grilledchickenwrap]

Great info... can my issue be like subframe bushing ? sound is coming from my front wheel passenger side. kzbin.info/www/bejne/jHS9npltmNGlfsk