How to Replace Front Wheel Bearing 2006-2011 Honda Civic

Buy Now!
New Wheel Bearing from 1AAuto.com trq.video/ib-1...
New Wheel Bearing Set from 1AAuto.com trq.video/ia-1...
This video shows you how to do the replacement yourself on your 2006-2011 Honda Civic. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This repair was done on a 2009 Honda Civic LX 1.8L Sedan 4-Door FWD Manual and the process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
Tools you will need:
• Flat Blade Screwdriver trq.video/obmE...
• Pry Bar trq.video/oUM-...
• 19mm Wrench trq.video/oW4-...
• 10mm Socket trq.video/obdA...
• 17mm Socket trq.video/obxG...
• 19mm Socket
• 32mm Socket trq.video/ocN-...
• Brake Caliper Hanger trq.video/oi5-...
• Torque Wrench trq.video/oaHc...
• Brake Parts Cleaner
• Copper Anti-Seize
• Gloves trq.video/oabN...
• Safety Glasses
• Floor Jack trq.video/o7k-...
• Hammer
• Jack Stands trq.video/oU5-...
• Punch
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Honda Civic 2006-2011 8th Generation: • Honda Civic 2006-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@diablo2815]

I took the lazy more expensive way out. I bought the loaded knuckle with the bearing already pressed in along with new ball joints.

[@tiocruz1836]

what happened to the knuckle u pressed the bearing into? u installed a brand new knuckle with bearing and hub also when u pressed that bearing in u didn't put any grease on the bearing u installed it dry..... not to mention if I was resusing that rusty knuckle I would've wire brushed it and painted it with some corrosion reducer paint....

[@user7xz38v4]

Anybody noticed that the wheel hub looks brand new at the end 🤔🧐

[@TomsCustomCreations]

Did you pull this car out of the Pacific Ocean?? So much corrosion! Done well to clean it up

[@dd___dc]

🤔🤔🤣😭 they found it next to the titanic

[@lumbearjack3722]

😂

[@joeflaco4390]

No wayyyy!!!!! My mechanic did it 400$ for both front....

[@Fishing_4_Recovery]

Any chance you can make a video of how to change a bearing without a press?

[@TRQ]

+Fishing_4_Recovery We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-TRQ

[@9er4life67]

Thank you, you are a life saver

[@panagiotis1519]

Once you press (or hammer) out the wheel hub, TAKE OFF THE BACKING PLATE BEFORE you try press out the bearing otherwise you'll damage the plate & the knuckle! I'm so upset I damaged the thing, the bearing would not press out & I had the caliper bracket mounting points flex on the edge while in the press bending the upper mounting. Bad day!

[@marvinurgel]

I am going to tackle this soon but a little confused on the removal of the sleeve from the old OEM wheel hub. Check out 13:56 , is that step necessary because when you remove the wheel hub, that sleeve if that is what is called will always be stuck with the wheel hub upon removal? if I get both new bearing and wheel hub, I do not need to do this step correct?

[@guirochulo]

Thanks , really was my solution your video ,

[@TheAed38]

How big of a hydraulic press do you need for this?

[@megaprimemaster]

The hub was not fine at 14:00

[@garyreams6248]

Where did you get spacer for bearing removal?

[@hellfire08]

How much should I charge to do this job 🤔

[@yvnggbeast528]

My guy has all snap on tools