Follow along as we replace our carrier bearings in our 300ex project. A step by step video of a start to finish bearing replacement. Thanks for watching, dont forget to subscribe and comment below!!!
Пікірлер: 63
@swickj_7 жыл бұрын
Very comprehensive, really helped me out. Much appreciated!
@grindinggearsgarage95787 жыл бұрын
Thank you! Please subscribe to our channel and like the video!!!
@quadbrothers58014 жыл бұрын
Used this to fix my 250x! All same parts! Thank you! Very helpful.
@robinsonsauto8 жыл бұрын
Nice! I like this format. Keeping it real, making do with what you have. felt as though I was in the shop kept looking for where I sat my beer lol
@grindinggearsgarage95788 жыл бұрын
+robinsonsauto its a constant struggle keeping track of that pesky can of beer!!!! We seem to have the same issue tracking down the last tool we used as well, its a never ending cycle.
@noahkluesner Жыл бұрын
Very good video you do a great job on getting all the details and how to do it
@leoisthatcrazy50152 ай бұрын
Nice video man I have a Honda TRX-300EX 1997 and the axel bearing carrier is snapped off and the chain has become crazy loose and comes off.So this video helped out a lot.i have to order the part and do the whole procedure you done to put your axel and everything back together with me luck with the axel nut.🫡🤣
@mikeatv6 жыл бұрын
great video... helped me figure out how to put back together a 300ex i bought cheap.... thank for posting it...
@grindinggearsgarage95786 жыл бұрын
Thanks for watching!!
@thomashoward44278 жыл бұрын
I have a 2004 Honda 300EX in my rear bearings where completely ate up the one bearing by the sprocket wasn't even in there the raz was welded to the inside of the carrier which is aluminum butt a torch gt that raz out but that carrier is all chewed up I put new bearings in the carrier but I have a new one on the way with new bearings and everything in it thanks for ur video I have done everything to a car n 4wheeler but never messed with them rear carrier n bearing and only because of your video I was able to save hundreds of dollars by doing it my self n nt sending it to a honda atv shop
@grindinggearsgarage95788 жыл бұрын
thanks man. that's exactly why we started this channel. hoping to help as many people as possible. we will have some more 300 videos shortly
@thomashoward44278 жыл бұрын
I have a a very small chip in the bottom of my motor I hve a nuther complete motor I was wondering if I could take the side casing off the spare one n put it tn on my motor its the left side im just in w.v n while that's being done id like to bore it out to the first stage is thata job u would do ???? I have never trusted to send my stuff to a shop but ur tn video was so good I NC an n tell u know what ur doing n u dnt just slop stuff together I trust n know u would do hell of gm a a job
@grindinggearsgarage95788 жыл бұрын
+ryan howard yeah switch cases around is done all the time. mainly from the chain breaking or the master link popping and cracking the left side case by the drive sprocket. we do not do any machine work on cylinders but I would find a good machine shop in your area and have them tackle it. If you take it to an atv shop they are just the middle man and will find a machine shop usually.
@thomashoward44278 жыл бұрын
I would like to have u do do u know around what something like that would cost I wont hold to u that price just an idea
@grindinggearsgarage95788 жыл бұрын
+ryan howard it honestly varies by machine shop and location. my best advice is shop around as many as you can.
@TheTrumanZoo5 жыл бұрын
thank you man... for showing me what ill never be able to do...
@cipherten98214 жыл бұрын
Great video it walked me all the way through it.
@timglivefree8 жыл бұрын
lol that tough nut ... when I come across one that's really giving me trouble and I finally get it to brake loss ... I pull a tom hanks from castaway... (like when he made fire) I'm all WOOHOOO I have Broke it lose ! I feel you pain though ..nice vid
@grindinggearsgarage95787 жыл бұрын
hahah i can picture it now! i love having those aha moments
@tjerj14 жыл бұрын
Excellent video! Thank you so much for sharing!
@tracymiller18844 жыл бұрын
Thanks for the video, it will help me on my removal 👊👍
@jacobchapman52184 жыл бұрын
Helped know what to do but my axle nut was stuck so I had to cut it off, now i cant get the disc brake holder off.
@Vagitarion4 жыл бұрын
I'm glad I don't live where it's cold. Cause everything I removed came right off. Axle came out by hand.
@Vagitarion4 жыл бұрын
Thank you for showing what to do with the bearings!
@mikeowens84835 жыл бұрын
Thanks, for the video. tearing mine down.
@shawnfast98524 жыл бұрын
Old video but very helpful. If you see this how would I get my spacer of my axel?
@revlimiterlife62762 жыл бұрын
Very in detail thank you
@EliteGamingHQ5 жыл бұрын
Hey man, nice video! You really had to fight with it. I subbed, also you are not far from me.
@James7796ify3 жыл бұрын
Hey I’m about to install a new carrier and noticed my sprocket hub is wobbling is that related to bad bearings?
@roberthaberman9491 Жыл бұрын
What size nut did you use to drive the bearings in?
@DanteFeraco816 жыл бұрын
I got a 1987 250x are the castle nuts with the cotter pin the same size you think?
@chadlepak9612 жыл бұрын
When I did mine it had 2 bearings on each side of the Carrier. Is that normal or should I put 1 on each side?
@johnlouk76912 жыл бұрын
Do I need to grease these bearings or is it gear lube
@cs6528066 жыл бұрын
Good video but you should have broke the axle nut loose before anything else. That way the chain would have prevented it from turning if you left it in gear.
@jeffwhitsit63864 жыл бұрын
I’m literally putting a new axle and carrier bearing on right now and I can’t get the snap ring back on, any ideas ?
@kevinsturtevant272Ай бұрын
I’m debating on buying a carrier bearing or just the bearings themselves. Anyone have any advice? I don’t have a press. 87trx250x
@dustintownsend78103 жыл бұрын
Helpful
@connersnow2983 жыл бұрын
Nice vid
@Tippycrawdad3024 жыл бұрын
My caliper bracket is loose should I shim it or something?
@АндрейЧеркасов-ж9ш3 жыл бұрын
Спасибо🤝
@ihorsepoweri27887 жыл бұрын
How lond did that axel and career last?
@grindinggearsgarage95787 жыл бұрын
Erich Ireland I purchased the quad with bad axle bearings, and I parted it out and never got to ride it. Good quality bearings that are taken care of will last a while
@keenanjohn66718 жыл бұрын
I watched this video and I took it all apart and put the new bearing in and now the axle nut and the brake disc holder doesn't slid on enough,any ideas? Thanks
@grindinggearsgarage95788 жыл бұрын
The axle sometimes needs a few taps to pop into the carrier. the hub for the sprocket should be all but against the carrier
@keenanjohn66718 жыл бұрын
+Grinding Gears Garage i cant seem to get it to slide into it
@grindinggearsgarage95788 жыл бұрын
do you happen to have everything threaded in? as you thread the nut in (reverse thread) you gain more space
@keenanjohn66718 жыл бұрын
yup tried everything
@benrobles83466 жыл бұрын
im having trouble getting the axle nut off how do i get it off?
@grindinggearsgarage95786 жыл бұрын
its tough. they usually take lots of force and soaking with penetrate
@2andrewneff5 жыл бұрын
is this what i need if the rear end is shifting around
@hammer499465 жыл бұрын
Jack up the rear and move the axle back and forth up. You will be able to feel a lot of play if the bearings are bad.
@2andrewneff5 жыл бұрын
@@hammer49946 I pulled the axle out and the bearing looked fine, the caliper looks to be rounded out definitely need some help
@shadesmoto11388 жыл бұрын
i had to do this last summer but i also replaced the whole fucking carrier too so it took alot longer
@ravenracing7977 жыл бұрын
do you have to use a press to get the bearings in or is their another way I don't have a press haha
@grindinggearsgarage95787 жыл бұрын
you can just drive the nut out with a hammer and punch
@ravenracing7977 жыл бұрын
thanks
@josecollazos65 жыл бұрын
Grinding Gears Garage what year is the bike ? I have a 2006 300ex i bought a new axle and have to replace it would it be the same was to take it off as this one ?
@sk8terdude1011007 жыл бұрын
You didn't show how to put the oil seals and stuff in
@grindinggearsgarage95787 жыл бұрын
angus sauve the seals just push in. Not much to it
@sk8terdude1011007 жыл бұрын
Grinding Gears Garage my carrier didn't come out on the axle and doesn't want to come out general any advice?
@wheninrome425 жыл бұрын
well im never removing this shit! lol the cam that spins to tighten the chain is all seized up, looks like ill just remove a few links to tighten her