How to replace Peugeot key fob or key case in 9 steps!

[@Sowar]

Thanks very much! A couple of suggestions to make it even easier. 1. Open the fob at the bottom with a coin not the other key. 2. Push the pin back in with a pair of pliers not a hammer.

[@Servicetutorials]

Sowar Thank you too!

[@ianschofield6440]

Many thanks, this was brilliant, very clear. Didn't know how to remove the blade. To open the case I used the end of a teaspoon (with a square end) or a screwdriver of the right size. Used long nosed pliers to hold the pin while locating it. Tapped in with small hammer. Hint make sure you are on a clear table with a clean floor. Dropping the pin almost inevitable.

[@Servicetutorials]

Thank you for your feedback!

[@briantaylor4110]

Thankyou, thankyou, and thankyou. Cheapest I could get in UK was £158.00. Bought casing online for £10.00. So grateful. Fixed just as you described. Worrying now Russia attacking Ukraine

[@Servicetutorials]

Thank you too for watching!

[@javadsaiyed9044]

Thanks for showing the correct method. You saved my £90. Thanks again

[@Servicetutorials]

Thank you too for the feedback!

[@asegoful]

In a few words...YOU ARE A GENIUS.

[@Servicetutorials]

Thank you, Felix!

[@Lakesman5308]

Great video , a little fiddly but sorted within 10 mins

[@Servicetutorials]

Glad it helped

[@patistreet]

thanks for your help! If I'd like to replace the cover side with bottons only, would the new cover work with the old one?

[@Servicetutorials]

I think that it is not possible, are not compatible.

[@rayfinkle2805]

Very informative and saved a lot of hassle. 😊

[@Servicetutorials]

Glad it was helpful!

[@ROBOK2K7]

Damn this took an hours patience getting the pin back in but great vid and I couldn’t of done it without it! Thank you 👍

[@bd_shafiulh71]

great tutorial! an absolute legend mate cheers

[@Servicetutorials]

Thank you for the feedback!

[@robindavies485]

Thanks a bunch. Saved me a lot of messing and time. Appreciated

[@Servicetutorials]

Thank you too for your feedback!

[@Egress__9]

Thank you so much. Your video helped me a lot.

[@Servicetutorials]

Thank you too for watching!

[@winston-1111]

thanks a lot!👍 instead of a nail I used a thin screwdriver and hammered it trhough with the backside of a bigger screwdriver😂 and I used a set of pliers to keep the pin in check when re-instering it..again hammering it with the bigger screwdriver.

[@Servicetutorials]

Thank you too for your feedback!

[@manocita]

Thank you so much for this video! I just managed to do this for my key!! Thank you!

[@Servicetutorials]

Glad it helped!

[@cronut7113]

This wasn't too hard, I did it with a 10 year old key and pulling the blade away after removing the pin was the hardest bit. Years of damp and grime made it quite hard too pull, I made a lever out of a ring spanner and a rod through the other end and eased it out levering back and forth in 2 directions. I happened to have a cheap watchmakers tool for removing links lying around following a previous DIY job. It worked a treat as a rod for hammering through the pins. Thank you

[@Servicetutorials]

Thank you for your feedback!

[@joeypinto9859]

Hello, could you share where you have purchased the sticky badge for the back of the key case? Thanks

[@Servicetutorials]

Hello! The sticky badge is coming in the package with the key case.

[@rwhite5529]

Excellent method to replace the blade i.e. remove the pin rather than disassembly of the spring mechanism

[@Servicetutorials]

Thank you for watching!

[@mikerhodes3273]

A great help easy to follow many thanks

[@Servicetutorials]

Thank you too for watching!

[@dereksteele1866]

thanks man made very easy for me to when i seen your video

[@Servicetutorials]

derek steele Thank you for watching!

[@jaguarcarrera]

Please help: in the new key there's no pin holding the blade but a kind of hole, maybe a small ring, I could remove the pin from the old key with a nail and hammer but not the blade from the new one.

[@cliftonshelly3154]

Well after stabbing my self with the point I used and bleed everywhere, I eventually did it with the help from this video, thanks

[@lennartstek8899]

No rfid chip issues? Everything is in the big chip?

[@leapy99]

Thanks for posting. Removing the key is easy when you've seen it done.

[@Servicetutorials]

Thank you for watching!

[@phillipostadden6206]

Very Good thank you looks very informative, now just need to try this.

[@Genner35]

Cheers! Thanks for sharing the knowledge 👍🏻👍🏻👍🏻

[@Servicetutorials]

Thank you for watching!

[@eirebadboy]

Worked a treat, thanks.

[@Servicetutorials]

Thank you too for watching!

[@stephgawronska2441]

Cheers done it in minutes .only had the key fob a year or so didnt dare do anything till i saw your vid .😙

[@Servicetutorials]

Glad to help you!

[@dotnetdevni]

Did it come with the new mother board mate?

[@Servicetutorials]

Did you mean circuit board? No.

[@ron9509]

Switched it, was a hassle to put the pin back in, the pin was a little to big. But now my car wont open or close with the remote. I really have no clue, when I put it all back in it also doenst work with the old one all of a sudden. Really no clue what to do now.

[@Servicetutorials]

Hi! It is a problem with these new aftermarket Peugeot key fob cases. So, after you installed all the parts from the old key fob, you have to bend that small plate that has direct contact with battery to make it work. When you install those two parts from the key fob back, that small plate near the battery is not making contact with the battery.

[@Servicetutorials]

Or you have to synchronise the key.

[@letter992stuki]

Great video.

[@Servicetutorials]

letter992stuki Thank you for watching!

[@savedfaves]

Be great if the getting the pin out wasn't edited and we could see in real time. A better procedure might be to move the mother board and battery over to the new key and then bring both keys to the locksmith and ask him to cut the new key. This way the pin stays from the factory.

The holes on the blades don't quite line up on my old and new key.

[@charleslees]

Thanks - helped me to do what I wanted.

[@Servicetutorials]

Thank you for watching!

[@s.p1512]

What's that u used to open the case ?

[@Servicetutorials]

Hi! I've used the the blade from the other key.

[@s.p1512]

@@Servicetutorials Aww okay wish me luck n thanks for replying back to my comment n uploading dis video

[@davidmitchell2926]

Thanks very much mate.

[@grahamrich11]

Hi, I've got one of these. Do they have batterys that need changing ?

[@davidbolha]

Yes

[@diegohuijbregtsgarcia5102]

Yes. CR1620 button cells.

[@fernandodelgadillo6881]

Gracias! me ayudo bastante el video. Quitar el tornillo de la llave de repuesto fue super facil pero la llave original no tiene el orificio, es un simple clavo y me costo mucho quitarlo. Una vez que lo quite todo bien. En fin me ayudo mucho tu video, gracias!!

[@Servicetutorials]

Gracias!

[@oktopod7630]

Thank you man 👍👍👍👍

[@Servicetutorials]

Chelsea CFC Thank you for watching!

[@aastrologer]

Amazing Thank you!

[@Servicetutorials]

Thank you for watching!

[@truehack3493]

You are the best. Thanks

[@Servicetutorials]

Thank you too for watching!

[@bokicrv]

where i can buy thet logo

[@davidbolha]

eBay

[@robertibbotson409]

My pin wouldn't go back in so i put a small nail in it and used a cut off wheel to shorten it then sanded it flat.

[@Servicetutorials]

Thank you for your feedback!

[@setter000]

Thanks a lot

[@Servicetutorials]

Thank you for watching!

[@ΣΟΦΙΑΧΡΥΣΟΧΟΟΥ-ζ7σ]

Thank you !!!!

[@Servicetutorials]

Thank you too for watching!

[@FABREZY]

Grazie 1000 sei stato utilissimo!!!!

[@Servicetutorials]

Grazie mille!

[@anditubeeckx4119]

thanks!

[@Servicetutorials]

Thank you too for watching!

[@sir243_simr]

I just could not get the pin back in... Its v tight fitting without it.. It will probably do

[@hardplaypt]

My car key have a chip problem only could be solved with new one they want 180 euros I don't want to give 180 euros it's too much. I wanna learn how I do it

[@billbord3205]

They’re made to fail! Good vid thanks

[@Servicetutorials]

Thank you too for watching!

[@blighty3248]

Great video ....my problem is I changed the fob on my Peugeot 206 key and now the key won't start my car...Thought it was the car's battery because that's what it sounded like however even after jump starting..it still wouldn't work...them I tried my spare "non fob key" and my car started first time...any advice would be greatly appreciated as to what I did wrong... I Now know what I did wrong...I didn't transfer the transponder from the old case to the new one 😠

[@FamilyGuySweden]

Did you solve it ? how did it go?

[@blighty3248]

@@FamilyGuySweden...Hi yes it was the transponder...i had forgotten to transfer it over from the original key fob...works perfectly well now thank you....

[@rasheedalhammoud844]

Danke

[@Kramblueify]

I'm not sure what this achieves exactly apart from getting a new piece of black plastic ??

[@timbunker4529]

The case buttons break down over time, once that happens the key gets unreliable. Also the battery needs replacing periodically.

[@DarkHunterDJB13]

Excellent

[@inphanta]

You made knocking the pin out look easy. I tried it repeatedly and ended up bending the nails. :(

[@ianpeel4862]

Yep, did make it look a lot easier than it really is!

[@chrislang1945]

inphanta 4

[@GuilhermeSilva-kx6ms]

You saved me!!!

[@Servicetutorials]

Thank you for watching!

[@michatylicki17]

The hardest part is the hollow pin

[@savedfaves]

I don't believe the pin is supposed to be removed. Otherwise the replacement key wouldn't come from the factory with pin inserted. Procedure is supposed to be: buy new blank key. Open both keys using a coin. Move motherboard from old key to new key (that's why it's not glued in). Close both keys. Bring keys to locksmith and have locksmith key the new key in the shape of old key.

[@krystianbaamut1426]

Thanks!:-D

[@Servicetutorials]

Thank you for watching!

[@Chapps1941]

New ones don't have the pin. Replace whole key blank with complete old key

[@benskingle8927]

This helped so much! Thank you!!!!

[@mountainremedy1784]

Bit too fast for me to keep up and there music is really distracting.

[@Servicetutorials]

Thank you for the feedback! For the next videos we gave up the music.

[@tonyash9239]

Please tell me how the hell you get the little pin back in again ??!!

[@The_Internet_Diaries]

In local keycutter they asked me 190$ for key fob replacement

[@Servicetutorials]

Wow!

[@The_Internet_Diaries]

@@Servicetutorials Yep, managed to change it on my own, it only cost 10 EUR. Ordered one from amazon.

[@Servicetutorials]

@@The_Internet_Diaries Thank you for your feedback!

[@darkomilosevic4565]

Thanks i have winished in 5 minutes

[@Servicetutorials]

darko milosevic Thank you for watching!

[@stevenwilliams520]

The keys are not all like that ! 😂

[@albertkutw]

Great! It's definitely the best video for changing key fob on KZbin. b^_^

[@Servicetutorials]

Thank you for watching!

[@wojciech41]

Dziękuje,

[@peterpeterson9182]

Not easy trying to put the pin back in with sausage fingers 😄

[@derekweir7692]

Really, why didn't you just change the button portion of the key fob, swapping the electronics over too.

[@ROBOK2K7]

The cheap replaceable key fob button cover doesn’t fit the original Peugeot key back, mate. They just don’t click-lock together for some reason. It was the first thing I tried doing to save on having to do this.

[@Rapas4U]

*Fuyez les concessionnaires !!! Ça se fait tout seul, le remplacement n'est pas bien compliqué !!!*

[@pansiara7527]

Hahahha Minute 4:57 :-D easy ? :-D Hahhahahahah

[@61barrackroad]

Great now key doesn't recognise the remote fob press

[@RM97800]

Fob gets deactivated every time you replace battery, consult your car manual to reactivate fob (I am 100% sure that my car's manual has reactivation procedure explained in it)

[@61barrackroad]

@@RM97800 yeah it does but that doesn't work either.

[@RM97800]

@@61barrackroad Then I don't have any idea. I'm in a process of replacing fob right now (I have some trouble putting the pin back into a key and I left it for tomorrow [I have spare key set, so I don't need to rush it]). I hope I won't encounter any nasty issue once I'm done.

[@61barrackroad]

@@RM97800 might be the fob then thanks anyway

[@pansiara7527]

hahahhahahahhaha

[@desmondjeanpaul6553]

Thank you 😊

[@Servicetutorials]

desmond jean paul Thank you too for watching!

[@Chapps1941]

New ones don't have the pin. Replace whole key blank with complete old key

[@Servicetutorials]

Thank you for the info!