How to Replace Rear Struts 2003-08 Toyota Matrix

Buy Now!
New Strut & Spring Assembly from 1AAuto.com 1aau.to/ia/1ASTS00963
TRQ Struts are made to fit your vehicle exactly, just like the original part. Struts can wear out as early as 50,000 miles. You should inspect them regularly for leaks or wear. Save time, money, and hassle by replacing an entire strut assembly. This video shows you how to install new reliable TRQ struts in your 2003-2013 Toyota Matrix.
• Check here for more videos on the 2003-13 Toyota Matrix: • Toyota Matrix 1st Gene...
This process should be similar on the following vehicles:
2003 Toyota Matrix
2004 Toyota Matrix
2005 Toyota Matrix
2006 Toyota Matrix
2007 Toyota Matrix
2008 Toyota Matrix
Tools you will need:
• Pry Bar 1aau.to/oE9/1AXAA00020
• 10mm Socket 1aau.to/oaDC/1AXAA00017
• 14mm Socket 1aau.to/oaSd/1AXAA00015
• 19mm Socket 1aau.to/oVW/1AXAA00043
• Trim Tool Set 1aau.to/oPh/1AXXX00006
• Socket Driver
• Socket Extensions 1aau.to/oaSd/1AXAA00015
• Torque Wrench 1aau.to/oaei/1AXAA00044
• Liquid Thread Locker
• Rust Penetrant
• Floor Jack 1aau.to/oLf/1AXAA00068
• Hammer 1aau.to/oH3/1AXAA00091
• Jack Stands 1aau.to/oIF/1AXAA00065
• Ratchet Strap
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Toyota Matrix 1st Generation 2003-13: • Toyota Matrix 1st Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@SchmidtRandolph]

If you remove the narrow storage tray behind the seats as well as the spare tire cover tray, the nuts for the strut are accessible to be removed and torqued with a 3/8" torque wrench without removing any of the trim panels on the interior. I was also able to vacuum under the back seats with that narrow tray out. A brick-and-mortar store had a video up showing the process without removing the trim panels.

[@dasspr]

So you basically will spend 90% of the install time with the trunk plastic pieces lol

[@Swarm509]

The best kind of KZbin video, straight to the point with clear info and good camera angles.

[@TRQ]

+Swarm509 Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@bransoncarlton5425]

" A loving BUMP" wails the hell out of it with a hammer! Great VID!

[@MrBobsVids]

I call you the 'Terminator' of car repair, just getting it done with no fuss, total pro, thanks for sharing

[@dalesmith3473]

Wonderful video, BEST ONE ON KZbin. You explained the WHOLE process, others skip a lot of steps. Thank You.

[@javierh6997]

Thx for this great diy video. Torque for bottom nut on 19mm sockett was 101ftpounds on other videos and for the top it was 29ft pounds on top bolts with 14mm socket. This video shows all 59ft pounds. Hopefully someone can double check this for me. Thx in advance

[@phxamigo]

threadlocker in rust country????? should be using anti-seize on all nuts and bolts

[@bransoncarlton5425]

Your front strut vids are the best on the net! THANKS

[@Charles-vw6hr]

It's a very good video thank you I used to to replace my strut on my 04 matrix. However mine had three bolts in the trunk. And the bottom mounting bolt. Not sure why yours had that other bolt ;)

[@igsaturation]

Awesome. Thank you, quick, fast and clear. The front struts vids are as good.

[@TRQ]

+Ig Saturation Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

[@ex-engineer6657]

I just finished this job. It's totally unnecessary to remove the interior side and rear cover panels. Dropping both sides at the same time by removing the bottom mounts helped a lot.

[@DriveShopAutomotive]

No need to remove both Side Panels.

[@warrenmclaughlin9554]

I would have torqued the lower strut bolt with the vehicle off the ground to prevent torquing against the bulging bushing. Just my opinion.

[@maximegagnon8597]

Torqued!!!!! great video

[@donalddunn7362]

Pay attention to the hooky dues lol

[@otimaldo]

I'm definitely only using a wrench. Not removing all that.

[@dre6036]

You guys need to define if you have the both rear struts out at one time, or your doing one at a time

[@j0hnnyb0y]

How do you know if you need front or back struts??

[@josesalvadorguillen]

"vehercle"

[@Charles-vw6hr]

I see now. When you have the strut out you have 2 studs on top of the strut mine has 3. 04 matrix. Same difference I guess it just stinks for you that you had to do that one from the bottom

[@Computerguy2052]

The hard bushing didn't come with the new parts