How to Replace Rear Wheel Bearing 1994-2004 Chevrolet S10

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ia/1AAXX00125
This video shows you how to install a rear wheel bearing on your 1994-2004 Chevrolet S-10. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
1994 Chevrolet S10
1995 Chevrolet S10
1996 Chevrolet S10
1997 Chevrolet S10
1998 Chevrolet S10
1999 Chevrolet S10
2000 Chevrolet S10
2001 Chevrolet S10
2002 Chevrolet S10
2003 Chevrolet S10
2004 Chevrolet S10
Tools you will need:
• 13mm Socket 1aau.to/oa/1AXAA00015
• Bearing Puller
• 1/2 Inch Ratchet 1aau.to/oa/1AXAA00043
• 1/4 Inch Ratchet 1aau.to/oa/1AXAA00017
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXAA00015
• Torque Wrench 1aau.to/oa/1AXAA00044
• 5/16 Inch Wrench
• Bearing Grease
• Gear Oil
• Gloves 1aau.to/oa/1AXSS00048
• RTV
• Safety Glasses 1aau.to/oa/1AXAA00343
• 5/16 Inch Allen Wrench 1aau.to/oa/1AXAA00006
• Drain Pan 1aau.to/oa/1AXAA00320
• Grinder
• Hammer 1aau.to/oa/1AXAA00091
• Magnet - Extendable
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@testuser3167]

Refreshingly complete video of the job! I was looking for this job for a 2004 Trailblazer, and didn't find much, but this looks to be nearly the same, except for the drum brakes vs. disc brakes, and I can figure that part out 🙂 Thanks for posting this!

[@Mike_The_Hog_A_Nator]

I'll be tackling this project on my 02' Blazer ZR2 drivers rear in a few weeks. Thanks for the info..

[@Mike_The_Hog_A_Nator]

Great info, I'm doing this on my 02' Blazer ZR2 & it has a Locker in it. Kind of hard to get that C clip out & you definitely need a magnet. I used the puller tool to hammer out the bearing & the seal at 1 time. Now it's time to get the bearing in all the way (waiting on the bearing driver kit) & then put everything back together. Not a hard job, that locker just kind of threw me off.

[@claudiocrespillo3224]

Excelente video 👌.... felicitaciones

[@JamesChilds-rr1oe]

Is this procedure the same for both right and left wheel bearing replacements?

[@gusiracheta9977]

Is it the same process for the other side?

[@scottymoondogjakubin4766]

A just in time video ! i have 2 s10's ! One needs rear axle bearings and the other needs a seal ! do you have the part # s for that s10 ? I think my 94 has the gt5 axle

[@donaldharris1134]

I have the same truck what part and oil did you use?

[@12345Flipside]

Hello. I want to replace my rear hub bearings and the differential cover. There are 4 sizes (7.50, 7.625, 8.50, 8.625) for the cover and gasket, how do i know what size i need? And what is the correct rear differential oil, for my 1999 Chevy Blazer 4.3l V6 AWD...? Thanks!

[@rafaelgarcia7030]

How do u know if it the axle shaft or the wheel bearing is wore out

[@denverkenyon3203]

When taking the drum off, just adjust the drum brake adjuster…..to bring the shoes together