dude you’ve saved me so much money just by watching your vids, i swapped all my front suspension and now the valve covers thanks 🙏
@s33therfan6 ай бұрын
Great to hear , and I really appreciate you watching. Thank you for the great feedback.
@twinkleberry13174 ай бұрын
Thank you much made this easy for me as an 18 year old with little experience with this stuff was putting in like 2 quarts every week
@s33therfan4 ай бұрын
Great job , and thank you for the terrific feedback.
@NeoSpace386Ай бұрын
Those with the 3.7L that find this video like I did, seemingly as no one has made a vid for the 3.7 the difference please note is you have to: 1) release the water line clips at the back firewall 2) the unplug the wiring harness from the computer and radio ground etc.. note everything's positions 1st Disconnect the other line from the coils and injectors, and the position sensor below bottom of the passenger side valve cover. When that's all off Route main harness behind the engine just past the valve cover. Now you have easier access to the back bolts they still suck but its easier. You will have to do this to be able to get the valve cover off anyways, the harness prevents you getting the clearance you need to get it out. I only did the passenger side that was leaking. Seems that seal tends to go 1st on the lower back corner because of the proximity to the heat from the catalytic converter. It lead to oil dripping on the catalytic converter and making smoke and a burning smell as it gets worse.. The other side may not need it. crankcase ventilation hose will likely be cracked and need replaced on both sides.. Good luck! Also protip: buy the victor reins set with the hard carrier to make the install so much easier.
@s33therfanАй бұрын
Thank you
@gueto70Ай бұрын
I was watching to find out if the brake booster had to come out for the drivers side on my 04 3.7. Did the passengers valve cover few years back. New rockers and lash adjusters "lifters" on the passengers last weekend. Just unplugged the injectors, coils and position sensor for elbow room to work. Nothing else was in my way.
@davidadrianmorales65853 ай бұрын
good video. wouldnt pressure wash an old vehicle like this. extreme purple power or similar degreaser, parts cleaner, brush, low pressure hose rinse, and a rag wipe...more work and takes longer but lower risk of wire or connector damage
@PrintTech-3D2 ай бұрын
For those wondering the torque recommended by dodge is 105 inch pounds.
@lonesapper2 ай бұрын
Awesome video! Thanks very much!
@jaimejay60566 ай бұрын
Mine are smoking a little bit so I think its time to replce them. Same seepage you had just worse. Was smelling it a few weeks Go,now its bad enough for it to smoke when it hits the manifold.
@michaelloms3067 ай бұрын
Hi, i watched one of ur videos for ford edge rank nd pinion replacement, my question is do ford edge 2007 - 2013 use the same steering rank n pinion ( hydraulic)
@s33therfan7 ай бұрын
As far as I know , 2007-2014 use the same.
@michaelloms3067 ай бұрын
@@s33therfan thanks
@chrisdickerson62344 ай бұрын
Blew a hole on my valve cover driver side back side on ram 1500 4.7 2012 any advice for me
@mr.h.83635 ай бұрын
Where is the last stud fastener(the plastic piece) on the driver's side of the 2004 4.7l 1500?
@mr.h.83636 ай бұрын
Purple power or Super Clean are great cleansers!
@s33therfan6 ай бұрын
Yes they are , thank you for watching.
@jaimejay60566 ай бұрын
Im wondering if it would even be safe to drive it to get the parts.
@s33therfan6 ай бұрын
I would probably fix it before driving it , if possible. Hope all goes smoothly. Thanks for the feedback.
@kalebstolpa74466 ай бұрын
How long did this take you to do?
@s33therfan6 ай бұрын
I believe I spent around 4 to 5 hours total with the cleaning and everything. Thanks for watching , much appreciated.
@Helloyes65924 күн бұрын
@s33therfan what size bolt you use for the cover to remove