Thanks for this video. Have to do this this weekend, and I feel much better going into it now.
@PeterFinnTheCarDoctor5 жыл бұрын
Great !
@louisvilleslugger39795 жыл бұрын
MAN THANK YOU SO MUCH FOR THIS! 92 Toyota, has 200k miles and would not start one day. Oh God, what am I getting ready to get into! lol
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks
@claudioa.parragonzalez58410 ай бұрын
great trick! people usually mark the pulley/engine. Marking the pulley/belt is much better. Even the mighty Scotty marks the pulley/engine!
@PeterFinnTheCarDoctor10 ай бұрын
Great point!
@osvaldob79394 жыл бұрын
Thank you peter you did a good job I'm going to do the timing belt in my camry 2.0 1985
@PeterFinnTheCarDoctor4 жыл бұрын
Ok, I read your comment and Thanks 👍😀
@JohnEboyee4 жыл бұрын
Forgot to rotate the crankshaft 1 7/8th with loose tensioner to pick up belt slack as the final step before tightening tensioner bolt. Critical step so the belt doesnt jump and/or develop an awful slapping sound.
@PeterFinnTheCarDoctor4 жыл бұрын
Thank You for comment. 👍😀
@JohnEboyee4 жыл бұрын
Thank you for your videos. Hoping to be one of the last '93 Camrys on the road =D
@arunayuven21024 жыл бұрын
Thanks, but as for me I always Tim the engine by using the down belt cover to Tim the grandshaft second I put the camshaft on point 👈👌👌👌👌
@bernardocisneros4402 Жыл бұрын
You can run into problems that way.
@jonathanngo91717 жыл бұрын
thank you for your instruction, exellence job.
@PeterFinnTheCarDoctor7 жыл бұрын
Thank You. :-) BR Peter
@davidessien54652 жыл бұрын
Good work sir!
@PeterFinnTheCarDoctor2 жыл бұрын
Thank you! Cheers!
@pedroluizsignore4582 Жыл бұрын
Hello! Please, could you tell me if when the timing belt breaks on the Toyota Camry 2.2 5S-FE engine there is damage to the cylinder head and valves?Thanks.
@PeterFinnTheCarDoctor Жыл бұрын
Yes it will
@bernardocisneros4402 Жыл бұрын
@@PeterFinnTheCarDoctor No, that is wrong. The Toyota Camry 2.2 liter 5S-FE engine is a non-interference engine so pistons will not collide with valves if timing belt breaks.
@bernardocisneros4402 Жыл бұрын
@pedroluizsignore4582 If the timing belt breaks on the Toyota Camry 2.2 Liter 5S-FE engine, the pistons will not hit the valves. The Toyota Camry 2.2 Liter 5S-FE engine is a non-interference engine, so you can drive it until the timing belt breaks. The only bad thing is that it might break in an area where you'll be stranded and have to get your car towed.
@davidessien54652 жыл бұрын
A client called me to check is Toyota Camry 2000 model with a 5sfe engine which always have a broken timing belt about 4 days after replacement. When I examined the car the only thing I saw that seems to be faulty was that the belt was weak, not really tensioned. The engineers have replaced the timing belt adjuster but to no prevail, the belt keeps cutting off. There was no oil on the belt that could be responsible for that. Please help me, what could be causing the belt to cut frequently?
@PeterFinnTheCarDoctor Жыл бұрын
Good comment 👍
@robertgorge1152 Жыл бұрын
Thank for your video.i will do change my camry 1999 very soon.i am not sure like 100000 mile or 5 years or 6 years of drive.
@PeterFinnTheCarDoctor Жыл бұрын
Glad it helped
@jorgedosanjos66452 жыл бұрын
Hello Friend... I have a Toyota corona engine 3Sfe that broke the timing belt, in this case there is warping of the valves????....
@PeterFinnTheCarDoctor2 жыл бұрын
Ok, can you rotate the engine pistons?
@darthmal7 жыл бұрын
I did this and the car is running smooth, except the temperature gauge goes all the way to hot. The car is not overheating though. I replaced thermostat but it is still overheating according to gauge. I put the heater on and air comes out warm.
@PeterFinnTheCarDoctor7 жыл бұрын
Ok, you need a new radiator, radiator fan and water pump
@darthmal7 жыл бұрын
The kit also included a new water pump, gaskets, seals and all,
@darthmal7 жыл бұрын
Water pump was also installled during timing belt. Car was fine heat wise before I replaced the belt.
@7smr6 жыл бұрын
Make sure your coolant temperature sensor is working and bleed all of the air out of the cooling system. Check other videos on youtube on how to do these.
@Ltholst76 жыл бұрын
Darth Mal. Sounds like a bad temp sensor. That's a simple fix.
@TheZippydoda1234 жыл бұрын
Why no new timing belt as long as you have it apart?
@geojor7 жыл бұрын
thank you for this ...
@PeterFinnTheCarDoctor7 жыл бұрын
Thank You. :-)
@jesustorres38634 жыл бұрын
Where did you get the jaw pulley
@SuperHtownswag4 жыл бұрын
After installing the timing belt and removing slack. Im noticing that the crankshaft pulley timing mark is aligned right. But the camshaft mark IS NOT IN ALIGNMENT. ITS CONSISTENLY FORWARD BY 2 inches or so...again this is when the harmonic balancer is at the zero mark. Is this okay? Im referring to the 'camshaft gear'...the camshaft gear hole is past the camshaft vertical notch/camshaft seal area. ie. on every 2nd complete 360 degree turn of the crankshaft gear...the camshaft hole is at 1 o' clock versus the camshaft vertical mark which is 12 0'clock. I want to know can the car still run okay despite this? I can tell that the camshaft marks are off because I made marks with white out before installing the belt. I have not tried to start the engine yet either.
@PeterFinnTheCarDoctor4 жыл бұрын
Good Comment. Thank you!👍😀
@TheRoadLessChosen Жыл бұрын
So what was the answer?
@bernardocisneros4402 Жыл бұрын
@SuperHtownswag Do not start your car like that. There's a very good possibility your pistons will collide with your valves and cause major engine damage. You need to watch another video that shows you how to start from scratch. You'll need to line up the hole in the camshaft gear with the vertical notch on camshaft bearing cap while the timing mark on the crankshaft sprocket is lined up with the mark on the engine block.
@bringthethunder3746 жыл бұрын
Thanks for your help
@PeterFinnTheCarDoctor6 жыл бұрын
Thanks too. :-)
@mattm32744 жыл бұрын
Your belt has slack when you tightened the tensioner belt causing y=the belt the be out by 1 tooth. Look at your white painted timing marks on the belt.
@siennachappell7 жыл бұрын
put a breaker bar on the crankshaft and wedge it in somewhere. Then crank the engine quickly and hey presto it will be loose and you can remove it by hand
@PeterFinnTheCarDoctor7 жыл бұрын
Hi and thanks for your comment. :-)
@lanazaakat94665 жыл бұрын
I dont think breaker bar would be a good idea.
@devilmecare5 жыл бұрын
Socket with a long ratchet if you don't have a puller. The bolts on the pullers won't fit in the holes. Both manuals show this type of puller.
@kotae7643 жыл бұрын
What happens if the crank is off time with the cam after that tho?
@bernardocisneros4402 Жыл бұрын
@siennachappell What if the car starts when you crank it? Don't you remove fuses for ignition and fuel pump? Then start car until it dies out and try starting another couple of times to make sure car doesn't start? Do you have to crank the engine or just tap the key a couple of times to engage the starter until the 19mm bolt on harmonic balancer loosens? You're missing a lot of vital information. You're giving just enough information to make this dangerous. Please elaborate next time so there isn't a possibility of someone getting hurt.
@michabosch11384 жыл бұрын
I have a problem with my crankshaft When it start it made a noise, is a TOYOTA CAMRY LUMIÈRE 1998 what is the sollution ??
@PeterFinnTheCarDoctor4 жыл бұрын
Thank You. 😀👍
@dynjarren54545 жыл бұрын
Dangit ads ruin the video...2 minutes into it and it gets stopped Really hate that
@AlexStypik7 жыл бұрын
Not good to pull crank balancer like that with that puller, there are bolt holes in center to do it right without breaking rubber on balancer.
@PeterFinnTheCarDoctor7 жыл бұрын
Thanks for info. :-)
@devilmecare5 жыл бұрын
You are using the right puller. There is no rubber on this balancer.
@garynew96372 жыл бұрын
Will the engine run if the belt is one tooth out?
@PeterFinnTheCarDoctor2 жыл бұрын
Maybe No
@bernardocisneros4402 Жыл бұрын
Yes it will, but don't run it like this. Will get bad gas mileage and cause other costly repairs. Fix it as soon as you can.
@giibzc23716 жыл бұрын
is this the same process for the 3s fe engine ???
@PeterFinnTheCarDoctor6 жыл бұрын
Yes
@giibzc23716 жыл бұрын
thank you
@lucasamoroso65675 жыл бұрын
Petter what is the correct point of the crankshaft 0.5.10.15 ?? help me?
@PeterFinnTheCarDoctor5 жыл бұрын
HI, I need to do new video
@devilmecare5 жыл бұрын
0 on the plastic cover.
@JohnEboyee4 жыл бұрын
0 TDC mechanical timing. 10 BTDC ignition timing
@bernardocisneros4402 Жыл бұрын
The correct timing is when the timing mark on the harmonic balancer is between 0 to 10 degrees with no jumper connected between terminals E1 and TE1. When you connect a jumper between terminals E1 and TE1 the timing mark on the harmonic balancer should be between 8 to 12 degrees.
@aaronhoward54675 жыл бұрын
Wow... Peter you relly go through all the comments, dont you?
@PeterFinnTheCarDoctor5 жыл бұрын
I try.
@peterfox8701 Жыл бұрын
you missed by one tooth check the last few seconds and look at the marks
@PeterFinnTheCarDoctor Жыл бұрын
Noted 👍
@ricardomares34305 жыл бұрын
Thanks🚙
@PeterFinnTheCarDoctor5 жыл бұрын
Hi and Thanks for comment. :-) Best Regards Peter
@tigergray11005 жыл бұрын
What is areare?
@adrianescobedo37877 жыл бұрын
thanks sr
@PeterFinnTheCarDoctor7 жыл бұрын
Thanks too Sir
@stankmontana47047 жыл бұрын
What year is the car ?
@PeterFinnTheCarDoctor7 жыл бұрын
1991
@goudotemesmer3612 жыл бұрын
Quel est la panne d'un moteur qui refuse de démarrer
@PeterFinnTheCarDoctor Жыл бұрын
Muchas gracias por el mensaje.
@ckawaokaw5 жыл бұрын
take easy when engine out of the car
@PeterFinnTheCarDoctor5 жыл бұрын
Ok
@josemanueljara20344 жыл бұрын
Exelente
@treyvaughn2619Ай бұрын
No no no no no!! IF YOUR MAKING A video to show PPL a Timing job show them the CORRECT WAY!!
@PeterFinnTheCarDoctor29 күн бұрын
Thanks for comment 👍😀
@namanconcepcion73433 жыл бұрын
No good Thanks anyway
@PeterFinnTheCarDoctor3 жыл бұрын
That's ok
@mabast0075 жыл бұрын
I do that shit without marking. Only slowere ''mechanics'' do the marking shit
@bernardocisneros4402 Жыл бұрын
Did you get that puller for crankshaft pulley at AutoZone? 😀😂
@PeterFinnTheCarDoctor Жыл бұрын
Yes
@shadezbp72984 жыл бұрын
Terrible don’t give up your day job . Translation fuked up
@PeterFinnTheCarDoctor4 жыл бұрын
Hi my Friend and Thanks for comment. 😀👍
@josesantillan46935 жыл бұрын
Thanks alot this helped me out alot with the information you gave
@aaronhoward54675 жыл бұрын
Brought one of these about a year and a half ago after watching the 2 door on hoovies. Spent 1800 Had 130k, its at 145 and runnig great. Very reliable car and was in mint condition auto,no sunroof. I did the valve cover gasket and its nice and sludge free inside. I plan on getting it to at least 200k. The higher in mileage ot goes, the more money i save per mile.
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks. Good feedback. :-)
@lucidx22 жыл бұрын
It won't even be broke in until 200k lol if you stay on top of your maintenance these cars can go 300-400k easy
@richardlasky7894 Жыл бұрын
💖💖🥰🙏🙏 * I am so grateful for your videos. 🙏 Love all the details you show.. ~ Your a life saver. 💪💯💯
@PeterFinnTheCarDoctor Жыл бұрын
Good 👍
@kwadjojoseph7116 Жыл бұрын
Professional work 100!
@PeterFinnTheCarDoctor Жыл бұрын
👍
@robertosamson59557 жыл бұрын
Greetings Peter! Thank you for the videos. Do you have any videos on timing belt replacement for the 2.4 liter (2LT) engines?
@PeterFinnTheCarDoctor7 жыл бұрын
Do you mean Toyota 2.4 ?
@robertosamson59557 жыл бұрын
Peter Finn Yes Sir, the ones used on old Toyota Hilux and Land Cruisers.
@Joe_3344 жыл бұрын
Hey Peter, just figured out how to knock out that SRS light on the dash. If the camry ever had a clogged AC drainage tube, it will backup and overflow, possibly damaging the control module under it. What I did was get another SRS control module and plugged that one in, and the light went out. This means that the crash sensors are good, and the clock spring is not shot. I know this is unrelated with this vid, but I hope this info reaches the person who needs it. In the state I live in, they are now checking for both the check engine light and the SRS(Red airbag) light to come on and then go off, on the dash.
@PeterFinnTheCarDoctor4 жыл бұрын
Hi, some airbag could be bad or some wire is loosen
@raufsahin3344 жыл бұрын
Thank u bro
@josealtamar54892 жыл бұрын
En español
@PeterFinnTheCarDoctor2 жыл бұрын
👍😃
@ibrarkhanus4 жыл бұрын
Not enough space??? buddy u got the whole engine out in front of u lol.
@PeterFinnTheCarDoctor4 жыл бұрын
Thanks ! Good comment. 😀👍
@JesusGuerrero-fe3du3 жыл бұрын
Great video can you make one on this engine how to replace cranshaft
@PeterFinnTheCarDoctor3 жыл бұрын
😀👍
@الامينحسنمنصوربدرالشيخ5 жыл бұрын
Thank you for this
@PeterFinnTheCarDoctor5 жыл бұрын
Ok
@0rbst3r6 жыл бұрын
What about all the oil all over the inside of the timing area?
@PeterFinnTheCarDoctor6 жыл бұрын
Hi, there was some oil leaks in upper cylinder head cover gasket.