How to replace Timing Belt & Water pump on Acura Integra part 1

[@CluelessEngineer]

me watching this after getting my GATES waterpump and belt kit in the mail. praying mine is ok

[@RBTheMechanic]

Take ur time and double check everything especially timing alignments

[@geecee2296]

Awesome video bro. Props on powering through every real life hiccup that popped up during the repair.

[@RBTheMechanic]

Appreciate it!

[@debruin14]

This was very helpful for my timing belt replacement. Thank you !

[@RBTheMechanic]

Welcome glad u like the video and was helpful

[@False_Death]

Man, thank you for posting such a detailed video on this job. There is absolutely no way I could afford to pay for this job to get done. I'm doing it on an old rusty 99 in an open shop in the hot Florida sun with bare minimum tools and wasps lol But as difficult as this is I appreciate knowing WHAT I need to do atleast. So thank you bro 🤙

[@hiramrodeiguezjr.8815]

Is the AISIN timing belt good too? Infound a kit that includes it all

[@RBTheMechanic]

Yes I use it lot

[@edgardjauregui3312]

I got a b20b in my integra it should still be the same process ?

[@RBTheMechanic]

Not sure

[@rapahelnavar6620]

I have a Honda civic 1990 ex sedan with a motor swap of a b18b1 gsr manual I replaced the spark plugs gapped and torqued, ignition spark plug coils, distributor ignition coil, fuel pump, battery, alternator, fuel injectors, cranks no start the mechanics bypassed the security system I lost the key fob if u could give me some ideas of what I could do to figure out my issue

[@RBTheMechanic]

Key fob u lost it? So car don’t start or unlock or alarm goes off?

[@edgardjauregui3312]

Are you sure it's a gsr a gsr it's a b18c1 the b18b1 is like the one from this video I would check out the main relay on my old Integra wouldnt start and it was a wire that came off the main relay plug remove the aftermarket alarm and see what it does

[@timcarter7051]

Mickey mouse eared thing is a "wing nut" and this" little guy right here don't loose it " after you pulled the crank pulley is a woodruff key.

[@jahrah7042]

Very Good informative video. I could sure use your eyes right now. Or run a couple questions by you.

[@RBTheMechanic]

Thank you my friend ask me anything...

[@oscargomez7623]

Very good descriptive video

[@RBTheMechanic]

Thank you!

[@ashkanmahouti858]

Nooo don’t use pry bar for the cover, hurts too much. Just smack it loose with rubber hammer. Other than that very good video, I learned a lot

[@loulouguerrero]

Does the harmonic balancer have to be aligned?

[@RBTheMechanic]

No that sits with key and it will only enter same spot

[@alexisrios9127]

That works for gsr?

[@RBTheMechanic]

It should be about same I think so

[@rowen.the_boat]

What is the broken mount called after the 16 minute mark?

[@RBTheMechanic]

Lower side engine mount

[@michaelkelly3501]

How long did it take you?

[@RBTheMechanic]

3-4 hours

[@Lagcams]

Appreciate you sharing your knowledge, saved me hundreds!

[@kaylonrobinson8974]

I can't find where to send a message. But im changing my head gasket on a 2001 acura integra gs. I was wondering if you could give me some expertise. Thanks Love the videos but the way. I learn something new almost every video. Keep it up

[@RBTheMechanic]

I’m not sure where to start I did many many head gaskets before I started this channel I wish I had recorded my old work anyways did u resurface the head?

[@gbaker2314]

Is there any way to see if engine is damaged due to the belt breaking before doing all this work?

[@RBTheMechanic]

That’s a good question u can align the valve to close up and then take out the spark plug push in compressor air with guage and see if it holds.

[@gbaker2314]

@@RBTheMechanic Thank you I will try that.

[@hectorgomez3580]

Men thanks for sharing this video it help me so much

[@RBTheMechanic]

Hector Gómez no problem bro glad to help u can always ask me anything ... please subscribe also subscribe to my other channel here’s a link kzbin.info/door/vqsPzqAZfVv_gjBYUFqNdg

[@JustManShii]

My timing belt actually ripped off my b20 while i was driving ,my buddy is gonna pretty much do exactly this ,replace my pump and Belt .what would be a rough estimate for labor for this type of job? (I’m buying the parts myself)

[@RBTheMechanic]

For this car labor would be around $270 if all goes well

[@yosammy1746]

All that just to remove that POS cover to access the tensioner.

[@RBTheMechanic]

Yes

[@jokerdempsey6109]

I need to know where my cams should be at when it went off time

[@RBTheMechanic]

Follow the steps if u got the save car

[@loulouguerrero]

Btw great video

[@RBTheMechanic]

Thank you

[@dee-zzz]

how did you get the harmonica balancer off so easily?

[@RBTheMechanic]

It wasent jammed or anything ... and we had done timing belt on this before few years back so it been on and off ... anyways is ur jammed up? The bolt?

[@mtrevlac]

@@RBTheMechanic trying this and my millawee 1/2" drive impact is not removing the 19mm bolt. Not sure if I have something that i could get it hot enough to help remove.

[@RBTheMechanic]

@@mtrevlac the crank bolt some times get tight they sell tool to hold crank it’s like 15$ and then put on pry bar with socket on center

[@baconstorm2259]

Anyone know what the torque specs is in that engine mount stud? I can't seem to find it

[@RBTheMechanic]

At what time frame u see it I can get it for u and year make model engine size?

[@baconstorm2259]

@@RBTheMechanic it's at 18:32 . I have the 1996 integra gsr model so the engine is the B18C1 version which is 1.8L. Thank you!!!!

[@RBTheMechanic]

@@baconstorm2259 I just posted a picture in the community section of the mount and torque

[@baconstorm2259]

@@RBTheMechanic you are an incredible person, thank you so much!!

[@WINTER1stDivison]

bro i have a whole ass cover where my tire goes so it doeasent show lioe that

[@RBTheMechanic]

Remove the cover

[@CayRome]

why is the camera shaking? Good video, thanks for taking the time.

[@RBTheMechanic]

Cay Rome sry about that my mount is broken had to put rubber band on it but it moved now waiting on new one please subscribe also subscribe to my rc channel the name is rcusa201

[@jack_cobetto14]

this is a good video, but way too many ads. It was like every two minutes.

[@RBTheMechanic]

Sorry I try to do smaller videos so less ads

[@christiannieves5762]

This bol is a nightmare guys 2 sec after is off lmao come on now i know a rel nightmare bolts

[@derekwilson8011]

Motor apply to 1997 Honda CRV B20 2.0

[@franciscocerda6806]

My crankshaft rotates along with my impact gun when I try and get the bolt off . Any ideas how to get it off???

[@RBTheMechanic]

En Serio? Well 1st thing 1st don’t impact it u can damage things u have to hold the harmonic balancer pully then try to impact it but since it didn’t come off they sell $12 tool that goes inside the balancer to hold for u. Now u have to do it mainly with hand power

[@RBTheMechanic]

En Serio? Here’s the tool on amazon Yoursme Fit For Honda & Acura Crankshaft Crank Pulley Wrench Holder Tool 50mm Removal Holding Spanner www.amazon.com/dp/B07439GHJ2/ref=cm_sw_r_cp_api_i_WG5BFbPBE7JVQ

[@Winterborne204]

@@RBTheMechanic Hey man thanks for the video, it is alot of help I unfortunately i am also having an issue with the timing bolt, due to where i live they use salt during the winter seasons and auaes terrible corrosion on every bolt... is this something I could apply a bit of heat to without ruining anything? Like 20 seconds give or take of some heat, thanks

[@RBTheMechanic]

@@Winterborne204 you have to try lubercwtion and heat maybe go easy don’t breaks it

[@angelgarcias7328]

W up bro thank you video where I can got good parts like timer bell need to buy the map sensor and idle air control valve to check auto parts to much money want buy something work c year let me now thank s much

[@RBTheMechanic]

Idle control valve is expensive but timing belt u should be able to get on amazon and water pump

[@angelgarcias7328]

@@RBTheMechanic i now idle control valve want $198 $218 to much check amazon got to much belt difrend want sonthing no need to change it like 3 year o mored hear to much $$$$ for change it thank s much bro g bless you y time

[@RBTheMechanic]

@@angelgarcias7328 no problem yea the idle control vale is expensive now days new cars have electrical throttle so idle control valve is eliminated the electrical throttle run fron$400-500 but I do remember honda and Acura idle valve run me around $190-400 and the brand was intermotor I used that brand lot but I think the price u got is fair Belt goes around $40 good water pump ASIN brand or delco like $70 or gates commin brand $40

[@angelgarcias7328]

@@RBTheMechanic that part can got Honda auto parts you send me it one check that mark yee want something find need change 1or 2 year life chager to much money to do the jod lolll thank bro

[@RBTheMechanic]

@@angelgarcias7328 lol true

[@EReelz]

Ugh I hate to see an ugly engine bay

[@RBTheMechanic]

Yeah aged our car but it need some good attention

[@RBTheMechanic]

@de dr yeah me too