Deore FH-MT410-B Hub. 36 Engagement points pawls system. Bearings list: 2 units 6903-2RS for Axle hub 2 units 6803-2RS and 1 unit 6802-2RS for Freehub
Пікірлер: 130
@strenkp Жыл бұрын
Top video, you are doing it right. You are explaining every step and everything is clear and visible. Thank you very much!
@maciej_ma6 ай бұрын
This video is pure gold for home mechanic. Thanks!
@LarsvanderPloeg21 күн бұрын
I have been searching everywhere for the way how to remove that endcap on the driveside. Just pull... I would've never imagined that.Thank you so much sir!!!
@michaelgomes14422 ай бұрын
video maintenance cube model FH-TC500-MS-B
@Calincillo2 жыл бұрын
Excellent job, great video!!!, thanks!!!!
@m.yankovАй бұрын
11:15 I had only 1 there and it had broken apart , I mean bearing are smashed , where is the other one ?
@arc21823 күн бұрын
Gracias por el tiempo que has dedicado a este video, es el mejor explicado y más detallado que he visto de este mantenimiento completo.
@cseles812 жыл бұрын
It is way easier to take a hot air gun, and heat up the freehub body nice homogeniously. I did it on a Sun Ringlé Micro Spline hub, the bearings have literally fallen into their nest. Wherever applicable, I will never use the hammer method...
@chrisphillips11146 ай бұрын
My cassette has a slight wabble. Definitely used correct spacers
@Apexifirdaus2 жыл бұрын
Hai i would like to ask u, after i change all 5 bearings and assemble the wheel back to my bicycle, pedal resistance is higher than before. Is it normal for new bearing to have this issue?
@rattlebob89845 ай бұрын
What would make me have a small wobble in the wheel? Hub nut is tight.
@solarheat90164 ай бұрын
Is that axle steel or aluminum? (Not the thru axle, but the real axle)
@Leo-gt1bx4 ай бұрын
What is the ring at 1:40? Do you prefer these to cup and cone?
@truer8702 жыл бұрын
that's why cone hub is the best choise. If u are not pro DH or Enduro rider cone hub is must have.
@solarheat90164 ай бұрын
Yes. What you want is the Shimano 500 series thru axle.
@Leo-gt1bx4 ай бұрын
Why does being a pro DH or Enduro rider make a difference surely this is less effort than replacing a hub.
@solarheat90164 ай бұрын
Cup and cone are easier to service than pressing cartridge bearings out and back in. This assumes the cone has damage and not the cup, which is how I always find them. But I heard heat guns work wonders for dropping the cups out if you need to.
@overexposurevideo Жыл бұрын
Thnx a lot for this great video! I'm struggling since one year to get my freehub off and thnx to you it worked out and I could finally service it. ! You made my day!
@peterderuiter2937 Жыл бұрын
thnx for this video. greetings from the Netherlands!
@cocoplops4982 Жыл бұрын
Fantastic video my friend! for some reason my freehub only has 2 bearings in it.
@JD-pw8xg2 жыл бұрын
Very useful! Many thanks!
@frankbroer7302 жыл бұрын
Verry useful video. I didn't use a hammer, I took the first bearring out by pressing the axle out.
@AMdvij2 жыл бұрын
Спасибо, вот бы видео для Shimano MT510
@VadevelaSailingcharter Жыл бұрын
Thanks for your help. One if the best maintenance description.
@TheDannyPutra Жыл бұрын
Salam Bang. Super detailed on the maintenance of the hub, and thank you for providing a very clear explanation! I was just wondering, should I just get the bearings changed right after observing play from the bearings on the shaft, even by a tiny bit? Thanks!
@evmechanic Жыл бұрын
Wasalam. If you can afford it and confident to do it with enough tools available, better to replace the bearings with good quality ones straight away.
@BEKrustie2 жыл бұрын
Super Helpful and better than the videos that my distributor provides!
@DMack-rm6giАй бұрын
Don't you think that what wears out is the axle and not the bearing? I recently changed the bearings and also the axle because after changing only the bearings, there was still play. What's more, by changing the axle and bearings it only lasted 2000 km and it is back in play, what do you think?
@evmechanicАй бұрын
The axle shouldn't be rubbing against the bearing hence shouldn't be worn. It should be rotating together with the inner bearing instead of rotating on the bearing surface
@DMack-rm6giАй бұрын
Well, they fitted me with a new axle and two new bearings at the bike shop, and after 2000 km the bearing had eaten into the axle and had a lot of play, what do you think they did wrong? or what do you think is happening? I have bought an axle kit plus bearings to assemble it better.😊
@14TacomaDR2 жыл бұрын
I am going into the 3rd week waiting for a delivery for a Shimano free hub for my 2020 Specialized Turbo Levo . They say in it shipping but can't say when it will arrive . Summer flying by and I can't ride. The number on mine is fh-mt510-b . Would any of the other models be compatible ? I need the 28 hole version.
@kcyclopoints2 жыл бұрын
Super video ❤️👍
@joerivers1716 Жыл бұрын
Thank you for this. Very helpful. My 2022 Cannondale mtb has a Shimano Deore MT410. Only lasted a few months before the bearings became very rough. My freehub only had 2 bearings not 3 like in the video. All of the bearings in my hub were generic and all were worn. Ordered from Phil Wood as they are near me.
@solarheat90164 ай бұрын
How is it holding up with the new bearings?
@Leo-gt1bx4 ай бұрын
How is it doing?
@winerrider2 жыл бұрын
Excellent, this really helped.
@eliomarbrenosilva6206 ай бұрын
Vídeo show
@TomCollins-c4h Жыл бұрын
I need help please. Got a new bike and have the same Deore hub but it is the front ones. My problem is the end caps or cones they are different and I dont know which ones are right or left. Thanks in advance.
@aaronalagos452 жыл бұрын
thanks. i wasnt sure what bearing was mine. i wanted to open it but i thought if it was broken and i removed it, i cant return and use my bike. i will just order bearings first before opening it
@lukas-a92342 жыл бұрын
The plastic ring you removed when taking off cassette, is that part of the hub or cassette? Do I need to put that on my new hub when I switch the cassette over? Thank you
@evmechanic2 жыл бұрын
I think it is part of the cassette if you look at this video kzbin.info/www/bejne/inW9pYqrYseLmKs
@lukas-a92342 жыл бұрын
@@evmechanic I see it now, thank you bro 👌
@divesh33662 жыл бұрын
Can I use 6903 zz instead of 6903 rs?
@evmechanic2 жыл бұрын
Should be same size but different sealing with ZZ being metal plates
@djmystery7235 Жыл бұрын
I lost the plastic ring under the cassette and I can’t find it anywhere, what can I do? Bike still shifts fine just had to change the limits on the derailleur
@jfritzinger2 жыл бұрын
my 12sp XT free hub is very slow...way too much resistance when free wheeling. I have cleaned it / removed it, but never opened the free hub. any tips?
@Tacoflyhigh4 ай бұрын
thank you so much for this tutorial!! I made the whole process through by watching your great video!
@oscarlenovo34504 ай бұрын
Thank you very much, great video! 👍
@franciscohidalgo12115 ай бұрын
Gracias. Thanks man. This was very helpful
@gmbmedia28 Жыл бұрын
Terima Kasih for this very useful video for me im using the same hubs
@samadmirzaei45825 ай бұрын
🙏🌹
@MichaelLeiBarrientos Жыл бұрын
There's a correction on the sizing though, written on your description is 6803-Rs and a 6802-RS whereas on the video they are labeled 61803-RS and 61802-RS, but correct me though if I am wrong. thanks friend
@evmechanic Жыл бұрын
6802 is standard sizing while 61802 is the sizing used specific by this bearing brand
@jonpelgone9 ай бұрын
Hello. Thanks for the video. If you have, appreciate if you can share a link for the bearing press tool you used to install new bearing. TIA.
can you open or regrease these bearings? i guess grease quality there is low.
@reinhardsowada9054 Жыл бұрын
Great video!!! Many thanks for the precise description. Just what I was looking for!!!
@ThunderWindz Жыл бұрын
03:20 what mm is that socket? good guide!
@Jookus2 жыл бұрын
Great Video thanks! I just had to opened my Freehub of the FH-MT410-B because of some cracking noises and finally two balls of the 6802 bearing were completely broken. For your intereset: In my case there is only ONE "6803 RS" and one "6802 2RS" in the freehub. I was a little confused that it is different to the one in your video even if it is the same article😉
@evmechanic2 жыл бұрын
Probably they put 2 in mine since it is an ebike so the torque going through the cassette is higher
@Jookus2 жыл бұрын
@@evmechanic Mine is an ebike too. It's a full suspension MTB from CUBE bought last autumn. That should be quite up to date.🤔 However my metal housing does not even have place for two bearings in a row, so that seems to be intendet. Maybe they really just changed it to handle more or less torque. But since my outer bearing broke already after 1500km, two bearings in row sounds better for me 😉
@evmechanic2 жыл бұрын
@@Jookus is yours also 12 Speed Shimano freehub? I think there's only 11 Speed HG and 12 Speed Microspline version available. Mine is 12 Speed
@@Jookus Mine also had one 6803RS and 6802RS, how did you take them out? The bushing between them fits tight and doesn't move, there is no way to fit the socket extension in there to hammer them out...
@cocoplops4982 Жыл бұрын
What grease are you using? thank you
@JoeIsles7 ай бұрын
Great video thank you so much. I ordered the bearings and press tool cant wait to get started. You did a great job explaining all the steps as well as which bearing and how many to buy awesome job my friend.
@Leo-gt1bx4 ай бұрын
How long did your original bearings last and what hub do you have?
@sebastiankania7422 Жыл бұрын
Thank you for this video!
@bz14292 жыл бұрын
Great video, I have the same hub, how many miles of service did you get out of the original bearings?
@evmechanic2 жыл бұрын
Mine is an EMTB, I got about 600 Miles
@SpecialyKey2 жыл бұрын
@@evmechanic trail usage or city/country roads?
@SpecialyKey2 жыл бұрын
600 is quite poor but at least it seems easy serviceable. Great video👍
@evmechanic2 жыл бұрын
@@SpecialyKey trail only
@zoranpl2 жыл бұрын
3000km on same hubs...not EMTB
@liveloveride16762 жыл бұрын
Great video, just what i have been waiting for, do you have a link for the bearing press, mine is the FH-MT401 is it the same bearings and is it the same procedure ?
@evmechanic2 жыл бұрын
Should be the same as the B at the end is for boost width. I am using this kind of press www.amazon.com/dp/B09GKG2F88/ref=cm_sw_r_awdo_4DX98C17BVA3CJKVCD4J
@manfirebirdF350 Жыл бұрын
thanks man
@Bicicastel9 ай бұрын
Muy bueno, muchas Gracias
@BoonMountainBike Жыл бұрын
very tedious job. not looking forward to it. Thank you for the video.
@Leo-gt1bx4 ай бұрын
Easier the replacing a hub.
@rogueknight99562 жыл бұрын
What shimano hub model is this?
@teabagNBG Жыл бұрын
i have this hub on my bike ... i want to switch to linkglide, linkglide doesnt work with microspline... can i change the freehub on the fh-mt410?
@evmechanic Жыл бұрын
I don't think Shimano is selling different freehubs for their standard hub
@Leo-gt1bx4 ай бұрын
Why do you want to switch, what are you using now?
@lodemerisback2 жыл бұрын
nice
@Gleeleeglee Жыл бұрын
Took out freehub and spin the inside bearings and it is not smooth. This should be the issues when I stop pedaling at 14mpg or higher there is a kick back felt on the pedals and chain slap. Initially I thought its the bottom bracket so I took off chain and spin fast forward and immediately back, it is smooth besides a little noise noise. So worn bearing inside freehub creates the kickback I experience?
@evmechanic Жыл бұрын
I doubt it since the bearing is only between the freehub and axle and the axle is not supposed to spin. Kick back probably related to the ratchet system
@Gleeleeglee Жыл бұрын
@@evmechanic When I took the bearings from the freehub out it spins smooth but when put inside the freehub is not but could be the pawls too I guess since its Shimano FH-MT410-B HUB thanks
@ТимурИзембаев-о2и Жыл бұрын
Здравствуйте как устранить лют ?
@karalis19762 жыл бұрын
Excellent job...this really helped
@edmejia98212 жыл бұрын
I want to share a video... I have hub with a problem its a little loose... How can i do to share you
@evmechanic2 жыл бұрын
You can upload to KZbin and put the link here
@DMack-rm6gi9 ай бұрын
Good Job
@kuatr00042 жыл бұрын
Nice stuff bud
@ckupcu2 жыл бұрын
Very good video
@luisstefan7160 Жыл бұрын
How many points of engagement does this hub have?
@evmechanic Жыл бұрын
32
@gmanhi52 жыл бұрын
Does the end cap just pull off? No screwing?
@evmechanic2 жыл бұрын
Yes. Need a bit of force
@edmejia98212 жыл бұрын
Excellent video....
@oliverp41152 жыл бұрын
Big help. Thanks
@bucke51082 жыл бұрын
Can a deore m5100 11 speed cassette fit on that hub?
@evmechanic2 жыл бұрын
11 Speed cassette is not using Microspline
@MrHugocad9 ай бұрын
Excelent.
@darbolozdarboloz93322 жыл бұрын
Muchas gracias!!
@eduardoulloalagos81342 жыл бұрын
Hola que tal los baleros a dónde los puedo conseguir?
@evmechanic2 жыл бұрын
You can try to search for the bearing number on the online ecommerce platform in your country. Physically any bearing shop should have them if you give them the bearing number
@FMiguelful2 жыл бұрын
Onde comprou a ferramenta azul? Obrigado
@evmechanic2 жыл бұрын
Online platform like Amazon should have it
@FMiguelful2 жыл бұрын
@@evmechanic obrigado, tem a referência também dos retentores?
@henrym18172 жыл бұрын
Hola cuáles son las medidas de los baleros del micro spline?
@evmechanic2 жыл бұрын
no hablo español
@evmechanic2 жыл бұрын
6803 x2 6802 x1
@henrym18172 жыл бұрын
Gracias 👍
@txemisuances43152 жыл бұрын
Buen video amigo
@evmechanic2 жыл бұрын
Gracias
@jlj5472 жыл бұрын
Is this applicable to the 11 speed hub?
@evmechanic2 жыл бұрын
Not really sure, probably the same construction but different freehub body
@jlj5472 жыл бұрын
@@evmechanic Ok thanks
@S0GGY-BREAD2 жыл бұрын
@@jlj547 will be the exact same procedure, just a different freehub body but everything underneath will be the same
@jlj5472 жыл бұрын
@@S0GGY-BREAD ok I am going to have shop do it cause just to buy the tools is more then what they charge to rebuild the hub.
@S0GGY-BREAD2 жыл бұрын
@@jlj547 that’s fair enough, tools are rather expensive haha