How to Set the Dwell on Spartan Electronics - What the Tech!

[@AngryBullAirsoft]

You guys are smashing it with the awesome tutorials and explanations 😍🔥

[@jonathancartaxo4180]

Super good instruction video! Thanks!

[@Ballab0y500]

das is genau was ich gesucht habe danke

[@cbradle4]

Thanks Glenn!!

[@tk2097]

When at max dwell and you're setting your psi make sure you've also set the hop as if you do this with zero hop you'll be throwing bbs out under power when you finally set it

[@TorksTube]

I was about to ask this hahaha, so with hop up too 👌🏽

[@Coreys77781]

How do you adjust the dwell on the mtw co2 setup?

[@Dr.Stanny]

QUESTION. Had my Polarstar Jack build for years, runs amazing, just over 80psi on the reg to hit 285 with .3s (legal uk limit). The fps is super consistent and very efficient. I’ve recently for a MTW wolverine and immediately using the same tank and reg set up it was only shooting at 250fps so had to up the reg to over 100psi to get the same fps reading, although my fps is about 270 but super inconsistent, one minute it’s 265, then after firing a few bursts it will sit at 280 before dropping again to 270’ISH’. And if I leave it for about a minute the first shot comes out at 320fps and then they’re back to a very inconsistent 270. So far the wolverine seems super unreliable regarding these statistics, the only thing that’s good is the receivers 😂😂 I’ve read it could be low nozzle dwell but I’ve already had to increase the fps let alone the dwell, if I gotta do that it’s going to be EVEN MORE inefficient! Could it be seals within the engine itself being silly letting air slip? Any other option I’ve ruled out because of how great my Polarstar build is using the same mags and hop rubbers etc etc

[@f.s.7490]

Clean your engine and relube it with TechT GunSav, same for the regulator. Set your dwell to max, adjust your PSI and then adjust your dwell. Make sure to use good quality BBs.

[@knastusse]

is that why you notice such a big difference in the joules when you buy 2 inferno engines to put in 2 different m4s

[@HappyH4x0r]

Did you set the hop at the beginning? How many stages are their until it's back to "full". Mine cycles through 15 but the first 12 make absolutely no difference in joule, the last 3 then nearly half it from 360 to 210. What could be the problem?

[@Walker-gr4bj]

Sounds like you have a shorter inner barrel/are running light ammo. Heavier ammo and longer barrel weight require more volume because both increase the time the bb stays in the barrel requiring air pressure. Dwell increases voluming, not pressure. So you're already overvolumed at all settings except the bottom 3 for your length barrel and your bb weight. Staying at setting 4 is ideal because it will be the lowest noise without sacrificing any performance.

[@josefjohnparnell]

so once i have set the dwell at my sight limit 1.1J how do i get the fps up to limit do i just turn my reg up ? wouldn't that make the jouls higher ?

[@thefreakyghillie]

when i do this mine starts changing the rate of fire, even after ive plugged in battery with trigger down

[@captainciccio1836]

How many psi should you set the regulator to Inferno gen.2??

[@reese1289]

Depend on your fields fps/joules limit I use 60psi for 1.14 joules

[@captainciccio1836]

1 j max

[@reese1289]

@@captainciccio1836 if you got a chrono start at 50psi and change it up or down to get exactly 1joule

[@MegaChickenPunch]

huh??? how are we supposed to know what role you want to play lmao, set it to 10 Joules Pepega

[@reese1289]

@@captainciccio1836 try 45 maybe 50 and fiddle with it from there

[@iiAnferny]

I love you

[@drug2]

How much PSI did you set the PSI for 1.2 J

[@HappyH4x0r]

Depends on your system, could be 60-80 psi

[@drug2]

@@HappyH4x0r what. I need 100PSI on my 10inch gen 2 to reach that Joule

[@HappyH4x0r]

@@drug2 hi, just chronod mine today again, got the mtw billet v2 with the 10.3" aswell, but the maxx hop up chamber, not the pricey one, the cheaper one. with 100psi iam doing around 1.5j with 0,32g bbs

[@drug2]

@@HappyH4x0r Interesting so you have around 0,2 - 0,3 Joule more. Seems like my gun is somehow broken. i cant even reach the 2J without putting the Reg up to 140PSI

[@HappyH4x0r]

@@drug2 like I said, depends on your system, what hop up unit do you use? The stock one? I think the stock one isn't as tight as the Maxx ones. You could put some silicone grease between barrel and hop up unit, but not into the barrel / hop.

[@FieldTim-n3o]

Dakota Forge

[@Bagoly_1]

U forgot to mentioned if u have a really short barrel , your J output won't change either max / min settings . then you have to go to minimum and add 1 or 2 up . and done . ( u have 13 steps (14 is the double tap ). so set it on 12 or 13 u good to go for really short barrel like scorpio have .

[@1337rage]

Missed opportunity to call this "What the Tech!" episode "What the Dwell!" 😅

[@cbradle4]

😂😂 Indeed!

[@dangerous_lemon7466]

I get 0.6 J with 128mm innerbarrel and 110psi. It seems to low. This is even with the highest dwell. Any tips?

[@simi044]

Replacing the nozzle and gripline helped me

[@robinkors3090]

Buuttt with or without set you’re hop ?

[@Bagoly_1]

u have to set your hop to the desired bb weigh for the correct J readings.

[@Mrgrantoloso]

How de we reset our dwell? im kinda all messed up over here lol was a good tutorial but i brain farted and messed it up lol pls help!

[@Jezzy_Airsoft]

Did you figure this out? I currently need to do same

[@nicob4599]

Same lol.

[@Mrgrantoloso]

@@Jezzy_Airsoft nope. legit still trying, keep giving up. nobody knows how and wolverine isnt any help.

[@Mrgrantoloso]

@@nicob4599 ya no luck lol zero videos or info anywhere

[@LordSteebu]

Not sure what you mean by reset but if you hold the trigger and insert the battery to go into programming mode, you then just hold the trigger until it double fires. That is set to max. Then just follow the steps to find the right dwell for your system. As for a factory reset, not sure it comes with that ability.

[@Iverson3]

bro my gun was shooting 170 fps cause of this, horrible system to adjust dwell, i took my gun apart like 12 times until i found out you can even adjust the dwell with this board

[@Dr.Stanny]

Proper silly

[@MegaChickenPunch]

Just use a chrono on the field. It will take like 30 seconds to set it up...