Thank you for making this video as simple as possible to show just what is needed. I appreciate these helpful videos, but the egos on this some of these videos.....UGH!
@pattayperformance8 ай бұрын
Glad it was helpful! Not everyone is an expert,I'm not sure why other people criticize them for that. We all started ground zero!
@jamesguralski51569 ай бұрын
Do you have a link to a new carb for this machine?
@pattayperformance9 ай бұрын
This should be it amzn.to/3vEfkLr
@jamesguralski51569 ай бұрын
@@pattayperformance thanks
@BrucesShop3 жыл бұрын
Well we all need help. thanks
@pattayperformance3 жыл бұрын
Absolutely! 🤙🏻🦅🇺🇸🔧
@spreadlove4312 Жыл бұрын
you talkin to low, i have that yard machine and i thinknit is the worse ‼️.... i have no idea who thought that was a good place for the pull cord....very hard to pull.... and also do you pull the lever where the handle bar at while starting or no
@pattayperformance Жыл бұрын
Don't hold that handle down while trying to start it. If you do that the belt tightens and adds a load to motor making it harder to pull start.
@markkeuter9552 Жыл бұрын
How do you adjust carb to throw snow better
@pattayperformance Жыл бұрын
You can raise the Rpms to 3,600 by adjusting the GOV Check to make sure your paddles aren’t worn
@MrDavidaslv Жыл бұрын
Very good explanation on the chuck hold open and closed
@pattayperformance Жыл бұрын
Thank You!
@pattylyn1846 Жыл бұрын
Just bought mine and tried firing it up for the first time and the lever locks and will only let me pull when it wants to. So when I finally get it to start, it run for 30 seconds and dies.
@pattayperformance Жыл бұрын
Did you buy it new? Return it if not time to go through the carb and as well as open up the idle circuit
@pattylyn1846 Жыл бұрын
@@pattayperformance yes I bought it new
@pattayperformance Жыл бұрын
@@pattylyn1846 start it with choke applied…let it warm up and gradually move the choke over
@pattayperformance Жыл бұрын
Make sure the gas you used is fresh and of course oil is topped off
@pattylyn1846 Жыл бұрын
@@pattayperformance thank you for your response. Unfortunately I'm still having issues. I will be returning it.
@streamguyentertainment2 жыл бұрын
Thanks. I am going to try this
@pattayperformance Жыл бұрын
How did you make out?
@streamguyentertainment Жыл бұрын
@@pattayperformance it didn’t work at first but then it worked the second time
@Turningwrenches853 жыл бұрын
Well if i ever find one like that here in Tennessee ill jump on it 😂😂😂🤘
@pattayperformance Жыл бұрын
Its coming!
@TheRustyRooster3 жыл бұрын
Nice of you to help him out.. Maybe the guy who owns that machine should watch this video.
@pattayperformance3 жыл бұрын
I sent him this video...figured he isn’t the only one. Great minds think alike🤙🏻🇺🇸🦅🔧
@RaleysSmallEngines3 жыл бұрын
That's a good idea Rooster! Do a short video of the proper steps to start and stop a customers machine and send it to their phone at time of pick up.
@bergan12273 жыл бұрын
Great vids I have a Ariens 8524 any suggestion on where to get parts I need the front blower housing
@pattayperformance3 жыл бұрын
Thank you! Second hand is your best option! Are you on Instagram? Send me photos of what you are looking for! Thanks for the view and comment, hopefully you subscribed to my channel 🇺🇸🤙🏻🔧🦅
@bergan12273 жыл бұрын
I’m looking to replace the complete front housing auger and all my housing is rusted out and I broke the auger gear last snow fall i was thinking of possibly going big bigger maybe 26 or 28 inch
@pattayperformance3 жыл бұрын
@@bergan1227 26 is fine 28” is stretching it. I think I have a 26” frame missing a few things here and there. I can take photos for you. I’m in LI,NY.
@bergan12273 жыл бұрын
I’m in White plains NY
@pattayperformance3 жыл бұрын
@@bergan1227 do you have an Instagram or email I can send you photos? It’s an ariens 8526
@michaelbryant47722 жыл бұрын
I've been using a product called TruFuel sold in most U.S./Can.hardware stores. It is sold as 40:1, 50:1 or reg 4cyl small engine uses. Cleanest fuel ever without the need for additives of any kind. No gummed up carbs and the dreaded ethanol problem.
@pattayperformance Жыл бұрын
I'm too cheap LOL
@kbssmallenginerepair26153 жыл бұрын
Nice video! Stay safe and warm out there!
@pattayperformance3 жыл бұрын
I’m trying! Lack of sleep is getting to me! I see some light at the end of tunnel! Hope all is well! 🔧🇺🇸🤙🏻🦅
@johncollier28062 жыл бұрын
I’m looking for that same engine. Anyone know the model number?
@pattayperformance2 жыл бұрын
You looking for exact replacement? Or you need parts for it? Which parts?
@johncollier28062 жыл бұрын
@@pattayperformance I was looking for a new carb but figured it out. Thanks
@pattayperformance2 жыл бұрын
@@johncollier2806 open up the idle circuit jet on the new carb before you install it. Glad you figured it out!
@mc2whls3 жыл бұрын
Choke does not need put back on for engine shutdown. Just pull the key out.
@pattayperformance3 жыл бұрын
I choke it back to reduce back fire and slow down the engine.
@RaleysSmallEngines3 жыл бұрын
Good one! People like us do it everyday and it's second nature to us. Rooster is onto something. Do a short video of the proper steps to start and stop a customers machine and send it to their phone at time of pick up.
@wrx2482 жыл бұрын
Worst snowblower I ever had. Every year I have to remove the carb and clean out the main jet. I've tried fuel additives but this main and needle jet just corrodes every year. Taiwanese engine and china carbs.
@pattayperformance2 жыл бұрын
I hate to be that person but it corrodes bc you keep leaving the old gas in it. Keep it simple…whatever gas you put in your car is the same gas you put in your snowblower. When you add gas to your machine throw some seafoam in there. At the end of the season, run the machine dry. GAS IS CHEAP IMO. The remaining gas in your gas can, dump in your car. Thanks for the view and comment, hopefully you gave this video a thumbs up to help the growth of the channel and get this video out to others. Keep me updated 🔧🦅🇺🇸🤙🏻
@jeremy-reitman10 ай бұрын
Any idea where I can find instructions on how to clean the carb on this one? I’m having the same problem as you.
@mrbriggs683 жыл бұрын
Would probably start faster if pull cord was in handle
@pattayperformance3 жыл бұрын
Agree but he disassembles it to transport it back and fourth. I’m glad he didn’t leave it pieces aka transport mode 😂