How to stop LT50 fuel overflow leak, LT 50 Quad Project series part 4 fuel leak from carb carburetor

Thank you for watching part 4 on how to repair an overflow fuel leak on an lt50 quad.
Check out the other videos on this project
Introduction - • SUZUKI LT50 children's...
Part 1 - Wheel bearing - • How to replace LT50 fr...
Part 2 - King pin - • How to replace LT50 st...
Part 3 - Fuel tap - • How to test LT50 fuel ...
Part 4 - Fuel leak - • How to stop LT50 fuel ...
Part 5 - Axle bearings - • How to replace LT50 re...
Part 6 - Chain / sprockets - • How to replace Suzuki ...
Part 7 - Carburetor 1 of 2 - • SUZUKI LT50 part 1 of ...
Part 7 - Carburetor 2 of 2 - • SUZUKI LT50 part 2 of ...
Part 8 - Rear brakes - • SUZUKI LT50 how to rep...
Part 9 - Steering Alignment - • SUZUKI LT50 How to set...
Part 10 - Throttle Cable - • SUZUKI LT50 How to rep...
Part 11 - Brake Cable - • SUZUKI LT50 How to rep...
Part 12 - Pull starter - • SUZUKI LT50 How to rep...
Part 13 - Tear down - • SUZUKI LT50 full strip...
Part 14 - Brake lock - • SUZUKI LT50 brake lock...
Part 15 - Front Weight - • SUZUKI LT50 How I fit ...
please like and subscribe, also please follow me on Instagram to keep up to date with whats going on on my channel @ Martys_workshop

[@MerchantMudCrab]

This man and his videos have saved so so many LT50'S Thank you, Marty!

[@Martysworkshop]

I'm glad my videos can help. Thank you for watching and following the channel.

[@lukehaymes4286]

Hey thanks for this tip, I’ve finally got my quad running after months of not knowing why it kept cutting out after a few mins. I actually had the opposite of this problem, my float was set up in such a way that it was turning the fuel off prematurely and cutting the quad out. Stressed me for months and I’d kinda given up. I bent that float a little and it’s running like a dream so yeah thanks for the tip you really helped me.

[@Martysworkshop]

Thank you for your feedback that certainly is a werd one fp luke. Glad you found it and I'm glad my video helped. Thank you again for watching

[@monisyed2394]

Brilliant instructions and explanation. I have the same problem on my daughters Quad was thinking it needs a service 😂 and was dreading it costing a bomb. Thanks much appreciated an easy fix your a champion have liked abd subscribed all the best. 👍🏽

[@Martysworkshop]

Glad my video could help

[@stevehayes900]

These videos are great, I recently salvaged a perfectly good lt50 from a skip. Got it running and overnight emptied a full tank of petrol onto my garage floor 😆 know I know why! Looking forward to more videos in this series!

[@Martysworkshop]

Thank you for watching i will have part 5 up soon.

[@NRNProductionsYT]

Thank u. This helped me fix my quad bike!!

[@Martysworkshop]

Im glad it helped, thank you for watching

[@FortWhenTea]

nice video man!

[@Martysworkshop]

Thank you for all your suport

[@solenebooker4789]

Topman many thanks

[@Martysworkshop]

Thank you for your support.

[@jasonpettigrew107]

Awesome videos!! I just picked up an 86 lt50 that is missing the cylinder vacuum stem and plugged with a set-screw. Having a tough time getting it started without it in place. Searching I cannot find a replacement to re-add the stem back. Any tips where to search? Also, will you touch on the wiring harness and magneto? Thanks and looking forward to your upcoming videos on the complete tear down and re-build!!

[@Martysworkshop]

I'm not sure if I'm honest i would like to think you could replace it even if you had to drill it out and just fit a standard fitting i will have to look into it. Sorry it took so long to reply.

[@eliphino12]

What is the port on top that doesn’t connect to a hose? It’s to the right of the fuel line

[@Martysworkshop]

It's just a vent there shuld be a pipe that comes off it and just hangs down behind the engine.

[@stevesworld7831]

Hey Marty, I have a 08 suzuki DZ50, I cleaned the carb and replaced the spark plug. Im having trouble getting full RPM. It feels like the rev limiter is going off. Is there a way to adjust it?

[@Martysworkshop]

I'm not familiar with that engine sorry

[@jonathanayers5540]

Do you have any videos of installing a piston and ring's in the LT50?

[@Martysworkshop]

Not yet sorry but it is on my list of things to do

[@conormcdade6021]

Hey mate can you point me in the right direction I purchased one yesterday off a fella all round very good condition except he said when storing it leave the fuel on, he said don’t turn it off cause when it gets turned off it leaked 🤯when it’s in the on position it’ll hold the fuel ok? Any idea

[@Martysworkshop]

Hello I coverd fuel taps in part 3 of this project, take a look in the description. All parts are listed. Thank you for watching

[@bladelad3797]

What's the valve just left of the clamp mate

[@Martysworkshop]

The mixture screw is just to the left of the clamp, and thank you for watching

[@richmead9569]

Excellent videos, thumbs up from me! Any of you guy's point me in the right direction for a 1995 workshop manual? 👍

[@Martysworkshop]

Try this one www.crservice.dk/Suzuki ATV/LT50/LT50.htm

[@seendizle]

my jr50 I had this problem. Bent the tab and fixed the problem. However when I lean it over to the right (the side the carbs on) the engine cuts out. What's causing this??

[@Martysworkshop]

Have you tried bending it back slightly? The fuel level might be too low in the bowel know causing it to suck up air when you lean it over.i hope this helps.

[@seendizle]

@@Martysworkshop yea i just did the float broke off the metal tab. Darn it. Super glue to the rescue. Just ordered a new float. It also blows alot of smoke and has oil coming out the exhaust. Does this mean the rh crank seal is gone???

[@Martysworkshop]

Yes i would say so how much oil do you mix with the fuel? Or does it run off the tank?

[@seendizle]

@@Martysworkshop it runs off the tank.

[@Martysworkshop]

Just checking you would be surprised how many people pre mix and put way too much oil in, yes i would agree with you and go for that seal, thank you for watching.

[@joeyd4708]

Would this problem also cause quad goin bad flooding etc

[@Martysworkshop]

Just a leak from this I'm afraid, i would check your jets or mixture settings i have done a 2 part video on carb clean and setup if you want more info. Thank you for watching