How to replace LT50 rear axel bearings and seals LT 50 Quad Project series part 5 rear wheel bearing

Thank you for watching part 5 of my Suzuki lt50 repair video series, in this part I show you how to replace the rear axel bearing and seals. Parts listed below
Bearing and seal kit used ebay.us/wd2M4w
Check out the other videos on this project
Introduction - • SUZUKI LT50 children's...
Part 1 - Wheel bearing - • How to replace LT50 fr...
Part 2 - King pin - • How to replace LT50 st...
Part 3 - Fuel tap - • How to test LT50 fuel ...
Part 4 - Fuel leak - • How to stop LT50 fuel ...
Part 5 - Axle bearings - • How to replace LT50 re...
Part 6 - Chain / sprockets - • How to replace Suzuki ...
Part 7 - Carburetor 1 of 2 - • SUZUKI LT50 part 1 of ...
Part 7 - Carburetor 2 of 2 - • SUZUKI LT50 part 2 of ...
Part 8 - Rear brakes - • SUZUKI LT50 how to rep...
Part 9 - Steering Alignment - • SUZUKI LT50 How to set...
Part 10 - Throttle Cable - • SUZUKI LT50 How to rep...
Part 11 - Brake Cable - • SUZUKI LT50 How to rep...
Part 12 - Pull starter - • SUZUKI LT50 How to rep...
Part 13 - Tear down - • SUZUKI LT50 full strip...
Part 14 - Brake lock - • SUZUKI LT50 brake lock...
Part 15 - Front Weight - • SUZUKI LT50 How I fit ...
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting this channel
please like and subscribe, also please follow me on Instagram to keep up to date with whats going on on my channel @ Martys_workshop

[@KruseNStuff]

Helped me out with my mini electric Chinese quad. Appreciate it Man.

[@Martysworkshop]

Glad my video could help mate, thank you for supporting the channel

[@harrygrove1732]

I Just bought a 1990 LT50, Looking forward to watching more of your videos! Keep it up mate!

[@Martysworkshop]

Thank you for watching. chain and sprockets is up next comeing soon.

[@johnshipp4496]

Thanks Marty, well explained and clear, great vid, cheers. 👍

[@Martysworkshop]

Thank you for your feedback

[@claireballantyne7178]

Very good video. Really easy to understand as always. Thank you xox

[@Martysworkshop]

Thank you for watching

[@clairedando1510]

Great vid 👌 👍

[@Martysworkshop]

Thank you for watching, will have to get you to feature in another one soon. X

[@soulreaperharleyrider]

I have some questions about this fuel line set up I have the the lt50 and I have the fuel line on the intake but when I got mine no lines where o. It how do they all go

[@Martysworkshop]

Hello jhon, I have done a video on the fuel tap and lines. It is linked in the description, or go to my channel and se the lt50 playlist

[@BenChiversAttention2Detail]

Hi Marty, great tutorials mate makes light work. I have just picked up an LT50 for my lad which I am gradually restoring…if the rear wheels are off the ground and the engine running with the rear wheels spinning there is a wobble to both sides….will this be failed bearings or bent axle?

[@Martysworkshop]

Can you feel play in the bearings when you rock the axel with the engine off?

[@andrewmcqueen6386]

Hi Marty, loving all these videos as I carry out my own resto of an LT50. When I did the rear bearings and put the axle back together, I torqued to spec and found the axle would no longer spin on the bearings. Is it just a simple case of winding off til it will spin freely? Thanks. Onto the carb vid next.

[@Martysworkshop]

Was there a spacer between the bearings? You should be able to tighten the nuts as much as you would like and it should still spin freely. And thank you for watching

[@andrewmcqueen6386]

@@Martysworkshop there was, there’s maybe something else I’ve done wrong. Maybe have to strip again and look.

[@Martysworkshop]

Look at how the spacer sits between the bearings, the spacer should be pinched between the bearings so shouldn't be loose. Let me know how you get on.

[@andrewmcqueen6386]

@@Martysworkshop will do and thanks. I also have a workshop and owners manual on electronic file I could send to you if it would be of any use?

[@Martysworkshop]

Thank you for the offer but i also have the manual on pdf.

[@mattmueller1340]

Did you ever get the measurements for the center spacer? I'm missing one also.

[@Martysworkshop]

I completely forgot sorry, send me your details and i will post this one to you if you would like. [e-mail]

[@mattmueller1340]

I sent you an email.

[@Martysworkshop]

Replied

[@jasonvigil45]

What size is the axel nut

[@Martysworkshop]

im not sure on the tread size but it is a 22mm spanner size if that helps, thank you for watching

[@teletupe1008]

As I was doing my beating, I found my lt50 didn’t have that centre tube. Where could I source this or does anyone know the specs so I can get one made up

[@Martysworkshop]

I have a spare hub assembly here so will remove it tonight and measure it up. Where are you from? Your welcome to have it if you can collect it?

[@teletupe1008]

@@Martysworkshop hey mate that would be much appreciated. And I’m in New Zealand

[@Martysworkshop]

@@teletupe1008 only half way around the world! I will reply with the measurements later.

[@teletupe1008]

@@Martysworkshop cheers mate