Tap to unmute

How to troubleshoot Lincoln Vantage no weld issue

  Рет қаралды 22,797

NTX Welding

NTX Welding

Күн бұрын

Пікірлер: 41
@jcwelding
@jcwelding 3 жыл бұрын
Great informative video. Looking forward to seeing the repair.
@Kryptokoz5555
@Kryptokoz5555 Жыл бұрын
Your the man. Thanks for posting. Saved me alot of $.
@Texaswelder71
@Texaswelder71 2 жыл бұрын
Just came across this video and man this is like one of the only videos talking about anything relating to a Vantage. I had a quick question since you seem pretty knowledgeable, my vantage just recently stopped working out of nowhere on me. It won’t turn on and the engine protection light is on. Oil and radiator fluid is good also. My guess is that either the temp sensor or oil pressure switch might be out so that’s why it’s not turning on? I don’t know much about working on machines but I would appreciate it if you or anybody else here could point me in the right direction!
@steve5912
@steve5912 7 ай бұрын
I watched the ads all the way so you would get paid I appreciate the help
@paultheisen5290
@paultheisen5290 3 жыл бұрын
Appreciate the videos Adrian, Great Job, keep up the Good Work!!!
@dowdleclay
@dowdleclay 2 ай бұрын
Your video helped me on my vantage 400 few years back. Now I have a commander 300 that keeps shorting/burning up the engine control board at start up. Any idea what would cause this?
@simonmason5856
@simonmason5856 Жыл бұрын
I found this very informative video after my vantage 300 stopped producing power. I ran all the checks you mentioned. Unfortunately i had no luck in finding the problem. What i did find is that at the bridge rectifier where the 200 wire connects, if i disconnected the wire to the filter capacitor that piggybacks this connection i get 12vdc. Once reconnected i only get a millivolt reading. The capacitor doea not show any voltage across the terminals nor does it read anything in microfarads when tested. Do you think it could be the capacitor. I replaced it with one off eBay and still the same. Maybe the ebay one us faulty also????
@junior721jh
@junior721jh 2 жыл бұрын
Thanks for video man, just helped me out with same issue!
@billbramlett5517
@billbramlett5517 2 жыл бұрын
Thanks for your videos there really helpful. You good man
@nickvo5859
@nickvo5859 3 жыл бұрын
YOU JUST SAVED ME 4000K
@thottaran
@thottaran 3 жыл бұрын
GOOD VIDEO, WE HAVE A VANTAGE 400 AMPER THE MACHIE GIVING A TROBBLE NO WELD OUT PUT, NO AUXILARY POWER. IWAS LOOKING THAT, BRUSHS ARE GOOD , ROTOR GOOD, I GOT THE VOLTAGE UP TO THE RECTIFIERR . AC 70 VOLT BOTTOM SIDE OF THE RECTIFIER AND 90 VOLT DC ON TOP. BUT I DONT SEE ANY LIGHTS COMING ON THE CHOPPER BOARD. WHAT IS THE NEXT STEP TO TEST PLEASE HELP ME.
@ntxwelding626
@ntxwelding626 3 жыл бұрын
You need to check and see if you're getting power to chopper board, if you are getting power in but not out it's bad. If you call Lincoln Electric and talk to a tech they can tell you what wires to test I do not know off the top of my head, have code number ready.
@nickagravante6917
@nickagravante6917 Жыл бұрын
Rotor is possible change to another rotor
@robertsilva657
@robertsilva657 2 жыл бұрын
How much did it cost to fix it ?
@Meowlux
@Meowlux 3 ай бұрын
So if it beeps when you check for ground. Means it’s grounding out
@rtm9412
@rtm9412 9 ай бұрын
I changed my brushes and have welding and aux power back, but the voltage screen wont show any reading. What should i check?
@juangarza2030
@juangarza2030 3 жыл бұрын
Mine lost power just like this one. I changed bridge rectifier and everything comes back on then it smokes bridge rectifier after 30 seconds and machine loses voltage outage again. What might I check. Thanks
@jorgeguerra5876
@jorgeguerra5876 3 жыл бұрын
That happens to mine to did you find out what it was
@alexayala6791
@alexayala6791 2 жыл бұрын
Thank you.
@xro5iex1
@xro5iex1 Жыл бұрын
Please help! I got a Lincoln vantage 300, when I flip the start switch the battery light comes on but the oil pressure light doesn’t. The machine turns but won’t start. Could it be the oil pressure switch?
@esausanchez8637
@esausanchez8637 2 жыл бұрын
Any ideas why I’m getting 158 Dc volts at my capacitor? My unit is not wanting to weld and is stuck at high idle as well
@weldingsolutions4264
@weldingsolutions4264 2 жыл бұрын
Where are you located man my 2017 vantage 300 stock on high idle and there is no riding on the amperage screen
@johnclark6742
@johnclark6742 Жыл бұрын
Have u figured out what your problem was here? I have the exact same issue on a vantage 400. Stuck on high idle and no reading on amp gauge
@CarrieMcLouth
@CarrieMcLouth Жыл бұрын
Can not find the following video. How can I find it?
@robmc9450
@robmc9450 Жыл бұрын
Please can I have some advice on my ranger 305 d , I’m having problems with lower output than amp readout @300amp, the clamp meter says 170amp @200amp I’m getting 120 , the 240v outlet seems to work fine as does the 110v , thanks for any help
@robertoobregon3750
@robertoobregon3750 3 жыл бұрын
Are the new rotors from Lincoln built any better
@ntxwelding626
@ntxwelding626 3 жыл бұрын
They look exactly the same to me, I can't tell a difference. They do come with warranty though.
@emmittcastro6153
@emmittcastro6153 3 жыл бұрын
Wat side of the slip ring is positive
@robertoobregon3750
@robertoobregon3750 3 жыл бұрын
Do you send the rotor to get rewound.
@ntxwelding626
@ntxwelding626 3 жыл бұрын
No it's cheaper to just buy new from Lincoln and get a 1 year warranty with it
@gusaguire9182
@gusaguire9182 3 жыл бұрын
I cant go past 30 amps any idea what's the issue
@j0rdan9016
@j0rdan9016 4 жыл бұрын
What does it mean when you get fluctuating numbers on your amperage display and no weld, but have aux power
@ntxwelding626
@ntxwelding626 4 жыл бұрын
Will the amperage adjust with the knob? Have you checked voltage at the terminals with a meter? Any difference in different settings? Remote switch in local? Have you dropped your panel and checked wiring?
@kgfarmfab8807
@kgfarmfab8807 3 жыл бұрын
Great video! Got a few questions for you, if you've got the time to respond. How common is it for the rotor to fail? Is it usually the windings shorting the slip ring to the shaft, or is it more common to cause an open between the two slip rings? Is it more common for the cheaper parts to fail, like the capacitor or rectifier bridge, or circuit board failure? I guess my basic question is how bad do they usually fail? I have a chance to buy a 2012 Vantage 300 without weld output and don't know if it would be worth the effort and cost to tear into it. I don't want to give more than $1,000 for it if it will cost me $2500 in parts. Any help, or thoughts on the subject would be appreciated.
@ntxwelding626
@ntxwelding626 3 жыл бұрын
Vantages can be good machines, Ive heard people love them and get thousands of hours out of them with no major problems. They run and weld good until they don't. I would say the biggest issue with the vantages is the cheap plastic or composite molded rotors. I see more rotors go bad than anything. Yes boards also go out but probably 90% of the time if youre getting no power at all and stays in high idle the rotor is shorted. The rotor last I checked was around $2500. Usually when a board goes bad it will stop welding in a setting or start welding spurraticly. Check out my video on testing armatures if you havent already.
@kgfarmfab8807
@kgfarmfab8807 3 жыл бұрын
Thanks for the reply, I appreciate the information. That's what I was afraid of on those rotors. I think I'll shoot the fella a very low offer and see where it goes from there. Least he could say is no! I really like the vantage specs on paper. I think it would be better than what I have now, and an SA200 is inadequate with the farm equipment and under ground water pipe repair I mainly do. I've got an 08 Ranger GXT now and would like the robustness of a diesel for generating power for water pumps and my small fusion machine. Thanks for the info.
@jonathangarzon2798
@jonathangarzon2798 3 жыл бұрын
@@kgfarmfab8807 why not go to a machine shop and have them make an adaptor plate for a diesel motor. Of your choice. Might be cheaper to put a bigger motor on your gxt.
@davidsipes592
@davidsipes592 Жыл бұрын
I have a Lincoln welder wp225g7 i have 110 v no weld no ark
@davidsipes592
@davidsipes592 Жыл бұрын
It was welding good and just stopped
@kylehoneycutt6833
@kylehoneycutt6833 Ай бұрын
I have a Lincoln 250 GXT and the kill switch stopped working, plus it will randomly put out 290 amps to the welding leads no matter what setting it is one. 👉🏻🤯💨
@ofraelmolinar5992
@ofraelmolinar5992 2 жыл бұрын
I get 6 volts on mine on the capacitor
Vantage 400 Troubleshooting
12:17
Lincoln Electric
Рет қаралды 73 М.
Why the Lincoln Vantage 300 & Tips on Welding Rods
9:59
Taylor Welding
Рет қаралды 19 М.
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
36:55
bayGUYS
Рет қаралды 1,9 МЛН
IL'HAN - Qalqam | Official Music Video
03:17
Ilhan Ihsanov
Рет қаралды 700 М.
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН
Testing welder armature/rotor
8:31
NTX Welding
Рет қаралды 18 М.
Free Lincoln Welder. Can We Save It?
56:13
Mustie1
Рет қаралды 882 М.
Lincoln BUZZ BOX stick Welder restore
26:18
sixtyfiveford
Рет қаралды 71 М.
Miller Bobcat 225 troubleshooting
10:17
NTX Welding
Рет қаралды 61 М.
SA-250 Lincoln welder trouble shooting
18:01
Duane Jackson
Рет қаралды 56 М.
SA200 Exciter coil testing
7:08
Kevin Gardner
Рет қаралды 36 М.
Idle Control - Welder Fix; Lincoln Ranger 8
27:59
Flat Thunder
Рет қаралды 23 М.
Miller Bobcat Welder/Generator Repair
22:24
Henderson Equipment
Рет қаралды 10 М.
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
36:55
bayGUYS
Рет қаралды 1,9 МЛН