How To Tune A BMW E36: Beginner Tutorial - Part 1

[@CanyonTuned]

Part II is here! kzbin.info/www/bejne/jYPclmdnjsegmrM

[@charlieward7606]

your a legend for making this content in 2021. ews delete is the only thing worrying me about my build and this helps a lot

[@elijahlogan1302]

Watched this about 50 times to get each part thru my brain , thank you just got the car connected and I’m about to start fixing my dash lights

[@CanyonTuned]

Glad you found it useful!

[@eddiesheeran5791]

I'm about to pick up a 97 328i with SAP codes. I want to do the delete myself and properly tell the ECU to stop caring about the SAP system. I haven't watched the entire video yet but I'll definitely be using it for reference. Thanks man.

[@CanyonTuned]

Yup sap delete is easy, just watch my intermediate tutorial as well

[@allankwai5158]

You have no idea how much this helped, granted I didn't do much searching to figure it out but I don't how to tune the stock ecu!! Or get access to it I should say

[@macelius]

You can just jumper the pins in the plug under the hood and use the OBDII port inside :)

[@CanyonTuned]

Correct! I found that out like a month after I made this video. I'm planning on making a new version with updated info soon

[@jonahreyes1165]

Great video that is helping me figure out how I'm going to tune my brother's E36. You have earned my subscription good sir. My only question you may be able to help me with is do you know if a Tactrix Openport 2.0 cable will work? Not a big deal if I have to buy a cheap VAG COM cable but coming from the Subaru world I already have a Tactrix ready to go. Thanks for the videos

[@CanyonTuned]

Tactrix is subaru/evo specific. Pretty much every platform requires a different tuning cable. I've collected about 10 different ones now. The only cable that's more universal is hp tuners, but that doesn't support bmws

[@kamilwiza1839]

could you please make a movie or send ecu with popcorn as "cleanish" has? :)

[@CanyonTuned]

Stay tuned, I will be doing a Part 2 video covering that

[@kamilwiza1839]

@@CanyonTuned I am waiting🙈🙈🙈

[@jimbovlogs8746]

Sick how you watch cleanish as well. Have the banner on my e36

[@kamilwiza1839]

@@jimbovlogs8746 🥰🥰🥰

[@zzzzf8404]

@@CanyonTuned where’s it at?!?!

[@cihangirasi]

Hi. I am using romraider. I have a ms41 stroker 3.0 m50 engine. First start in the morning is in the AFR lean 16 or 16.5 range. Afr is in the 15-16 range until the engine warms up. No engine problem. All sensors and elements are intact. No error log. After the engine warms up, afr is normal. Idle 730rpm afr 14. While driving 13.5. Acceleration and high speed and accelerator pedal full load 12.7. But in the morning the problem afr very bad. No air or vacuum leaks.

[@CanyonTuned]

You need to tune your cold start enrichment tables, I forgot which table it is but it has an X-Axis of coolant temp, and the datapoints are % enrichment. You'll want to bump that up a little

[@carrodeguasevo]

Hi, friend. the mega link is down, can you upload it again? Thank you very much for everything you teach us

[@CanyonTuned]

Sorry my account got hacked and I'm locked out. You can buy the flash tool on the ms41 wiki, it's a little better

[@carrodeguasevo]

@@CanyonTuned ok, no problem thx me friend :)

[@dalepillay5885]

Please can you confirm the pin numbers we need to weld in the obd plug😊

[@CanyonTuned]

Google ms41 wiki and look at the "enable write page"

[@CanyonTuned]

Pretty sure I mentioned them in the video as well.

[@dalepillay5885]

@@CanyonTuned thank you! Worked like a charm!

[@jupper2]

Ty so much man, helps when your beginner.

[@aidanbain9098]

Hey man - great video! Still helping guys years later. I downloaded RomRaider and MS41 Quickflash to mess with timing and fuel adjustments. I can read partial and full files from the DME (41.1), but have “errors preparing ECU” when going to write/flash a new tune. Pins 14 and 18 are jumped, along with 7 and 20 to enable OBD writing, any suggestions what I’m doing wrong?

[@CanyonTuned]

Did you try writing from the 20 pin in the engine bay? I've seen some cars dont like to be flashed from the obd port

[@aidanbain9098]

@@CanyonTuned I have a 20 pin to OBD2 port adapter on the way to try just that. Anything else to look for beyond that? Thanks for the feedback!

[@pepelen1588]

Hello, first i wanna say thanks so much for the tutorials they are really useful and well made, tho can you upload the flash utility somewhere again, because the links in the description dont seem to be working, thanks in advance :)

[@CanyonTuned]

This is a more up to date version and is recommended: sites.google.com/site/openms41/read-write-ms41/ms41-flash-tool

[@emersinn3729]

how do i figure out which ones is pin 14 & 18 on the connector as nothing internally is labeled

[@CanyonTuned]

Look at the connector on the car then match it up to yours. It's numbered there

[@rahimrustamov8241]

Hey, thank you for this video series. Before i want to get started on everything I had a quick question. I did the e-fan conversion just like yours with the relay and etc. My orange wire goes to pin 16 on the diagnostics connecter and at the moment its cut and directly spliced to the orange cable. I am wondering if Ill have to resplice the original pin 16 wire to the pin itself before I do any sort of tuning. And question 2 would be where did you route the orange wire as i see it going under the cowl to the fuse box? Thank you in advance!

[@CanyonTuned]

My efan is pretty ghetto rigged. My wire that goes to the fuse box is just soldered to a fuse that's hot when the key is on. That way the fan shuts off with the car. I'm not sure what you're talking about what the diag connector. Nothing fan related should be going to that. Mines wired to the main b+ terminal where you can jump the car from the front

[@auggie3936]

@@CanyonTuned Hey man nice video. You probably have lotta questions here but, do you recommened I do a tune like this after I just swapped to a m50 manifold? I dont know how to tune so Idk if I should just order the cable you bought.

[@georgedermitzakis4315]

Hi!!!! Men thank you 🙏!!! I have some questions for you though… Do you run a specific driver for that kkl ftdi cable ?? Anyway your video is very very very informative!! Thanks again!

[@CanyonTuned]

Yup, you can get the drivers here: ftdichip.com/drivers/

[@georgedermitzakis4315]

@@CanyonTuned wow thanks!!! Which ones are you recommending???

[@random5hit811]

Good videos 👍 .. can I use the Ftdi cable looks like the one you have but in the title of the cable it says for Volkswagen .. Seat .. Audi . I have a 95 bmw 318i trying to remove the ews2

[@CanyonTuned]

Should work

[@mohamed-ih9fd]

Hey dude nice vid but i dont have all paramters to change as you do what ist the problem?

[@CanyonTuned]

You are working from the full read...you need the partial file. Follow the exact instructions in the video please

[@mohamed-ih9fd]

@@CanyonTuned yes but then the program says ecu reject

[@CanyonTuned]

Then either you don't have the correct definitions or your specific ecu isn't supported

[@mohamed-ih9fd]

@@CanyonTuned it is supportet porbably this is what in romraider says this ecus is not supported ther ist not mine

[@mohamed-ih9fd]

@@CanyonTuned what you mean with definitions

[@alexx6558]

Hey man great videos i just got in to tuning i have romraider and a proper usb wire but i cant for the life of me make romraider logger work it will just constantly try to connect but wont any help would be greatly appreciated

[@CanyonTuned]

Are you using the obd or 20 pin connector?

[@alexx6558]

@@CanyonTuned obd

[@CanyonTuned]

You still need to jump the pins on the 20pin connector under the hood to get logging information. Refer to the ms41 wiki (Google) for the in information. There's two sets and they both need to be jumped

[@Tayu54E]

I have MS41 , got the file and disabled EWS. There is only OBD 1 connector inside my e36 which I used in order to read. How can I flash? How to locate the 14 and 18 to bridge them when there isnt x20 connector in the engine bay? Thanks!

[@CanyonTuned]

Then you have an obd1 car. You cannot flash it, you need a removable chip switched out in the ecu with a tune in it. Tons of them on ebay

[@Tayu54E]

@@CanyonTuned my bad its a 16 pin obd 2. That goes inside the car, I dont hve the x20 connector. The ECU is ms41 index, I have found out that pin 7 is the kline and pin 16 is the 12+ volt. Can i bridge 7 and 16 and try to flash?

[@benamatucci8014]

Cant seem to get cable to connect with Seimens tool. It works fine with other programs. Any idea why it wont connect?

[@CanyonTuned]

Make sure your cable is set to port COM 1 in device manager

[@agdwhite5421]

Hello!! Did you write the partial with the ecu mounted on the car? Is not necessary to use a bench setup? Ive seen a lot of people doing it just for a simple partial write and i was considering if its necessary or not. I know of something goes wrong you are f**d up but isnt it just a 1 minute work?

[@CanyonTuned]

You never need to bench flash these ecus. Just make sure you have a battery charger hooked up if you're doing a full read/write

[@agdwhite5421]

@@CanyonTuned Nice i thought so. Have you ever tuned a DISA btw?

[@Francix125]

hi, i liked the video but i have some questions... i have a '93 320i so it has a m50b20 vanos engine and OBD1 siemens ms40.1... so no flashable. but i know that it can be red from eeprom reader and up to here no problem... now, do you know if the file is the same as that of ms41? can you edit with programs like romraider? is it possible to use the program you show in the videos? Thank you.

[@Francix125]

because the problem is not so much the reading but the modification because I don't know if you can easily modify it as an ms41

[@CanyonTuned]

Yes, if you look at the romraider forums they should have definitions for the M50. You can try using tunerpro too I believe. Worst case scenario you can just use a binary editor but you have to know which specific sectors correspond to each table/value.

[@Francix125]

@@CanyonTuned perfect, I sincerely hope there are legible definitions for mere mortals

[@SonyPsp08888]

for scanning modules and coding what would be the process? could you make a video about it? awesome content!

[@CanyonTuned]

No idea how to code honestly

[@SonyPsp08888]

@@CanyonTuned ok, for scanning what program would you use? my e36 doesn't have a obd2 port underneath the footwell only the 20pin connector

[@MikeP41]

@@SonyPsp08888 check out my advanced tutorial, if you don't have an odb port just get a obd extension cable and run the 20 pin -> odb extension -> obd cable so you can have the laptop inside your car. Rom Raider logger works great

[@alessdiazlopez54]

Hey Bro! I have a 325i (bosch ecu, not siemens as you have). It's the same process to read and write the tune?

[@CanyonTuned]

No those require you to flash a new chip, please check out my e30 tuning video. It's the same process

[@E36_kidd]

I am really close I have the backup.bin on the computer now and I downloaded the ecu definition files and they are in the definition file manager but when I go to open image and click on the backup.bin it says that the “ecu definition not found” I have looked on the forums and can’t find anything to on there did you have the same problem

[@CanyonTuned]

Did you do a full for partial read?

[@E36_kidd]

@@CanyonTuned partial

[@ArtiGames15]

Is the software the same for M42B18 with a bosch ECU ?

[@CanyonTuned]

Nope, refer to my other guide. That's ODBI kzbin.info/www/bejne/jYK4iK2wpbefhs0

[@dexterpapasideris1706]

Hello there got a problem can you help me please got cables got the flashtool i bridge pin 14.18 but when im going to flash my ecu nothing happent (also it say cable connected but nothing more )any ideas?

[@CanyonTuned]

Make sure your cable is on COM1

[@dexterpapasideris1706]

it is on com 1 also redlight is on also it says cable connect but it doesnt flash the ecu @@CanyonTuned

[@dexterpapasideris1706]

so ok eveything work i just need the ms41 def cause roomraider doesnt open it do you know where can i download free? @@CanyonTuned

[@workout3389]

I have installed those ecu definitions but in ms41 I’m missing DTC codes removal and also speed limit in rpm to make launch control, any chance to get that?

[@CanyonTuned]

You need to be working for a partial file not a full

[@workout3389]

@@CanyonTuned yes I’m working on partial bin file but I have ms41.0 I think that’s the reason :c

[@marc8979]

I’m having issues with openms41 I can’t buy it and I found a link to the version you have, but when I hit partial or anything nothing happens. Device is connected, and bridge the pins under the hood with jumper wires

[@CanyonTuned]

Check device manager, make sure your cable is detected and the port is set to COM1

[@marc8979]

@@CanyonTuned it is, do you have a link to openms41? The website to buy it is down.

[@marc8979]

Also romraider logger doesn’t detect either.

[@MangoFlamingo]

Could I see how you did the weld inside the 20 pin. Like a photo?

[@CanyonTuned]

Open up the connector (there should be screws) and solder a wire to the back side of the pins mentioned. If you look very closely the pins are numbered at the front side.

[@MangoFlamingo]

@@CanyonTuned Thank you

[@MD-cf8hs]

Hi could you please confirm that this cable will work instead of ftdi chip?

[@chinoperez6504]

With OBD2 e36 can I just jump the pins and read it from OBD2 port or does it need to be with that 20 pin cable ?

[@CanyonTuned]

You need to jump both sets of pins (4 total) to use the obd port but yes it works

[@brevinolson8236]

@@CanyonTuned so I can’t click on the google docs and I need to figure out what wires I have to jump can someone help me??

[@CanyonTuned]

@@brevinolson8236 sites.google.com/site/openms41/read-write-ms41/enable-write

[@AbzakhVlogs]

Hi, after flashing the ecu, i got crank no start situation and getting these codes 100 control unit self test failed 68 tank venting valve Fuel pump is working but it looks like there is no spark Any idea ? Thanks in advance

[@CanyonTuned]

Seems like either you checksum isn't correct when you flashed it, or you have a mismatch of DME software versions. Without more information on the steps you took, It could be a lot of things honestly

[@AbzakhVlogs]

@@CanyonTuned thanks for the quick response All i did was Using the ms41 quick flash took a partial copy Open romraider to change the rev limiter hysteria to 32 to make it fast rev And then flashed to the ecu Tried to flash the stock partial file It flashes but still same issue crank no start “I can still read and write to my ecu with out a problem”

[@CanyonTuned]

Flash back to your original tune and try a different number, you might have gone outside the range of acceptable values. I've never messed with that specific setting before

[@AbzakhVlogs]

Problem fixed, it was all because of the ews module it was causing the dme to not fully write or flash which ended up causing to ruin the flash IC in the dme I had to disconnect the ews and bridge it Then to flash the IC module inside the dme Then to copy another dme and write it to my dme Then tune it and its done

[@AbzakhVlogs]

I hope it make sense

[@AsKmEeEh]

I have a k can cable would that work or do I need to get that vac com cable ?

[@CanyonTuned]

I think you have to swap one of the wires for it to work. Not sure but I would just buy the correct cable they're cheap

[@davidproud4039]

Nice video thanks. I'm looking to upgrade my standard S50B32 eruo engine into a race built/tuned engine (new pistons, rods, higher compression). Just need to find a person in New Zealand that can tune the dual vanos on a dyno with this method.

[@CanyonTuned]

S50 dual vanos is fairly easy to tune since it's just on/off, basically you want to do 2x runs of each intake and exhaust on and off and overlay you dyno charts to see where the power overlaps then set the vanos switchpoint 300 rpm sooner

[@LordTheodore04]

great video

[@radek788]

I connected pin 14 and 18 and turn on the quick flashtool and I can't flash. What to do with this?

[@CanyonTuned]

Are you using the obd port or x20 connector?

[@mikimouse6991]

I have ask about imobilizer can i with this rewrite imo and read imo?

[@CanyonTuned]

You mean EWS? See this video: kzbin.info/www/bejne/Y5WpcqSYnKl7p80

[@LSchon-wi2hd]

When i open the image in rom raider it doesn’t show me any table to modify it, is it a common problem?

[@CanyonTuned]

Sounds like you don't have the definitions loaded or the incorrect ones

[@bimmerbros1595]

hey the url for the MS41 flashing utility is not working anymore..

[@CanyonTuned]

Just buy the new quick flasher, it's much better sites.google.com/site/openms41/read-write-ms41/ms41-flash-tool

[@carmenridolfi7370]

I hope you see this comment. I know it’s an old vid but would you be able to turn off dsc through rom raider? or does it have to be dealt with separately since it has its own module

[@CanyonTuned]

I think that's part of one of the body modules that needs to be coded not tuned. Most people just remove the DSC hardware and pull the bulb in the dash

[@carmenridolfi7370]

@@CanyonTuned thanks

[@jami666]

Are the steps same for 96' 523i?

[@CanyonTuned]

Yes and no. You might have trouble finding the romraider definitions for that motor. People don't usually tune them.

[@jami666]

@@CanyonTuned it's got a siemens ms41 ecu with m52b25, did a bit of research and it should work, but i was wondering if those softwares even work on windows xp (shitty diagnostics laptop)

[@Vgk36]

I can’t download the definition tables ? I’m registered on the website. I have a 1995, 325IS. 7:54

[@CanyonTuned]

Please explain what's going on exactly.

[@Vgk36]

@@CanyonTuned yes if I go to the rom raider site where you have the links for the software /cable and definition tables everything is clickable except the bold definition tables area. I had to order another cable as the software can see the cable but won’t communicate with software. So this time I bought a ohp inpa cable no selector switch it’s just blue. I could screen record and send to you as well. Thanks 🙏 for the help

[@CanyonTuned]

@@Vgk36 Double check you're actually logged into the romraider forums or try a different web browser. I've never had an issue downloading definitions. Also Is your car OBD1 or 2? 95 was the cutoff for transitioning to OBD2 and some 95s are still 1. If it's 1 you won't be able to use anything in this tutorial, you'll have to refer to my e30 one

[@Vgk36]

@@CanyonTuned bam ! That's the problem. Mine is OBD1. Mine is production date. 3/95

[@ernisiekgaming1433]

Cant u show us how to do the step with connecting the opins?

[@CanyonTuned]

Unscrew the two screws on the 20pin connector. Split the connector. On the back use a jumper wire and solder it. It's dead simple

[@E36_kidd]

Can you load the partial map and unplug the car, then make your changes and then plug the computer back in once you have everything changed and upload the new map changes

[@CanyonTuned]

Yes the only time it needs to be plugged into the car is when you're actually reading or writing to the ecu. Or you need to log (see my other videos)

[@__akuuma]

@@CanyonTuned so could i grab the save file, unplug from the car and do all the changes, then just plug it in when i’m actually writing to the ecu when i’m finished?

[@CanyonTuned]

@@__akuuma You only need to be connected to the car when you're reading, writing or logging.

[@Josuer0491]

Does all of this works on m50 aswell??

[@CanyonTuned]

M50s use a removable chip that needs to be burned using an EEPROM reader/writer. Please refer to my E30 tuning video for more information. The process will be similar

[@CanyonTuned]

Working On The Part II Video This Week! Thanks for all the support

[@juancarlospreciadovillasen1543]

How to change the alpha n to tos in room raider?

[@jefftheheph987]

Will this work with 92 or do I need a different ecu

[@CanyonTuned]

That requires you to burn a removable chip, this is for 96 and newer

[@jefftheheph987]

@@CanyonTuned thanks for the response 👍

[@juanpenaloza1894]

Is this for OBD1? or OBD2? or Both?

[@CanyonTuned]

You can't tune OBD1 cars, they're removable chips

[@Heyhowdoi]

nice work bro

[@owardramirez7887]

hey man nice videos, Have you ever converted an ms41.0 to an ms41.2? I have read that it can be done in the RR forums but I am not entirely sure

[@CanyonTuned]

I've never done it, but be sure to use the new quick flash tool and follow this guide: www.romraider.com/forum/viewtopic.php?f=42&t=13063 Quick Flash: www.bimmertuningtools.com/flash-tools/ms41-quickflash/

[@nergimmm8308]

I know this is kinda dumb since in my country i'm not allowed to drive more than 109hp, but will this work on 316i e36? I don't have a license but i'm very interested.

[@CanyonTuned]

Depends on what year. If you have an early model you need to use my other video to create your own tuning chip

[@supabiscuit]

316.... You mean 318?

[@aidangray4374]

is this OBD1 or OBD2 LMK PLEASE!!

[@CanyonTuned]

Been mentioned a thousand times I'm the comments. Obd2

[@ismannr]

can this flash tool flashing ms41.3? or should I buy the quickflash tool from openms41 site?

[@CanyonTuned]

Try it, I believe it should

[@CanyonTuned]

Just read the notes "You can only flash this 257KB *.enc file with QuickFlash v2+."

[@suhaibelarar2440]

I bought an E36 m3 recently, my question is how to know if my car has been tuned?! Thank you

[@CanyonTuned]

The romraider forums have stock bins. Just compare it with your bin from the car

[@pavelshmelov5775]

Does the EWS have to be bypassed before any mapping changes are done?

[@CanyonTuned]

Nope you can leave EWS enabled and still make changes

[@milanmakesbeatscapsulecorp945]

Would you be willing to make me base map for my build so I can start and drive it to work out any kinks until I can take it to a dyno?

[@CanyonTuned]

Just scale your injectors, add a little fuel and take some timing out of it if you're forced induction

[@milanmakesbeatscapsulecorp945]

@@CanyonTuned I know but I don’t know how to do any of that at all this is my first build.

[@CanyonTuned]

@@milanmakesbeatscapsulecorp945 If you don't have a local tuner I personally would suggest just going with the TRM forced induction tuning solution. I can't just build you a base map

[@milanmakesbeatscapsulecorp945]

@@CanyonTuned ok gotcha thanks a lot man

[@huntercongdon7723]

Is this process the same for an e39

[@CanyonTuned]

That's an M54, and MS45, the process is completely different and way more complex www.ms4x.net/index.php?title=Siemens_MS45

[@mamar_b4554]

Hey guys ! Will it work on bosch DME ? Mine is m3.3.1 version

[@CanyonTuned]

Completely different platform unfortunately

[@meticulousm393]

Yo! Have you used the MS41 flashing utility back up? Want to make sure it’s legit before I download it onto my computer my browser instantly blocked it haha

[@CanyonTuned]

Yeah I really don't get why anti-virus programs have been blocking these lately. Been using both versions for 5+ years without issues

[@mxrlon.21]

i have the same problem, virustotal shows some shady thing's when i scanned it. how can i get the ms41 definitions without using the MS41 portal?

[@ThugzBunnyYT]

so complicated i just need to flash ews my sap and get rig of nmy cog light due to manual swapping

[@CanyonTuned]

I have another video for a one click solution.

[@Be11egem]

Ms41 won’t read my cable and all drivers are installed 😢

[@CanyonTuned]

Make sure your device is using com port 1 in device manager. That's the most common issue

[@rianeallen2348]

is the flash tool free?

[@CanyonTuned]

The one I shared is free, however it keeps getting marked as a virus for some reason...There's a new tool out that's $25 that does a much better job: www.bimmertuningtools.com/flash-tools/ms41-quickflash/

[@austingilstrap9395]

Once you head the “uhhm” you can never unhear it 😢

[@CanyonTuned]

This was one of my first videos, cut me some slack

[@E36_kidd]

Every time I try to down load the flashing utility on mega it just loads and then tells me to download again but now I have like 10 downloads that won’t open

[@CanyonTuned]

Can you be more specific about the error message? What version of windows are you using? You could be missing one of the .net frameworks

[@E36_kidd]

@@CanyonTuned I just bought the ms41 quick flash and I’m going to try it this way, it was asking me to open the download but every time I did it would load then ask me to do it again, so nothing was even happening.

[@CanyonTuned]

@@E36_kidd That's strange, I've never had an issue with it. But yeah ms41 quick flash is much newer and better anyway

[@E36_kidd]

@@CanyonTuned I got it to work after like 3 hours 😂 thanks for all the help and one last question, I know you can jump the pins that are on the cars obd2 connector but instead of that can you do it to the obd2 adapter wire instead.

[@CanyonTuned]

@@E36_kidd Correct, I prefer to jump the pins inside the round 20pin connector instead of messing with the car's harness. Just unscrew the connector and easily solder a wire across the pins inside

[@EkkoGG]

Would this even work for an obd1 for a 95 bmw e36

[@CanyonTuned]

ODB2 only, ODB1 cars need the removable EEPROM chip bench flashed

[@garfieldlover6662]

Anyone having problems with the definitions I can’t seem to find the right one

[@CanyonTuned]

What dme is it for?

[@i3abod55]

How i can programming e30 1987 ecu

[@CanyonTuned]

It's really not worth it honestly. You can buy performance chips on ebay for like $30. If you really have a unique setup, buy 27C256 type, a 28-pin DIL (Dual In-line) chips and an EPROM writer. TunerPro also has all the e30 DME definitions

[@tomschutte3789]

I can't download the romraider definitions.. can anyone help me?

[@CanyonTuned]

You need an account on the romraider forums I'm pretty sure

[@michaelkofla3159]

link to 32 bit java, i’m having problems, can’t run romraider

[@CanyonTuned]

Java is hard to get these days, you need to make an oracle account first to get access

[@BullEye96]

How about MS40.1?Can do this?

[@CanyonTuned]

You need an eeprom reader/writer and new eeprom chips. ODB1 cars are not flashable

[@BullEye96]

@@CanyonTunedThanks! How to finde you at instagram?

[@CanyonTuned]

@@BullEye96 armonic0

[@brightonchauma9570]

hie can you please send me the ms41 tool im a newbee

[@CanyonTuned]

www.bimmertuningtools.com/product/ms41-quickflash/

[@Antonnio22]

Can i do this on a 93 bmw e36?

[@CanyonTuned]

No but refer to my e30 tuning video, you'll need to burn your own chip

[@davids4099]

Great video, is there any way I can call you? I have a e36 that I can use your advice

[@CanyonTuned]

Instagram: Canyon.tuned you can message me

[@TheCC11]

97 e36 is OBD2 right?

[@CanyonTuned]

yes

[@875-performance4]

Can this software work in e46

[@CanyonTuned]

Rom Raider will but I think the ms43 needs a different flash tool

[@udj4414]

what year is this?

[@CanyonTuned]

99, last month of the e36 m3 ;)

[@LakixPompa]

Just a quick question, i dont really want to purchase the round connector that allows to connect to obd2, there is this guy who connected some pins together, and it allowed him to gain all the access apparently and use the obd2 inside the car. The link to the vide is here kzbin.info/www/bejne/oYiulIp4gqqGerM , would it be the same thing as buying the round connector and connecting the wires ?

[@CanyonTuned]

There's two sets of pins you need to jump to bypass the round connector, please check out the ms41 wiki for more information on that

[@MarekBeylich]

I can't access the flashing utility on drive

[@MikeP41]

Google thinks it's a virus, just turn everything off or try a different browser

[@MarekBeylich]

@@MikeP41 what exactly should I turn off, I just tried with edge and it doesn't work either

[@CanyonTuned]

@@MarekBeylich If that doesn't work you can buy the new version for $25: gum.co/ms41quickflash

[@MarekBeylich]

@@CanyonTuned just bought it thanks!

[@CanyonTuned]

@sillalexander Uploaded to MEGA and added link to description.

[@Juhkwez]

Can you do more of spaced pops. Like loud gunshots on decel?

[@CanyonTuned]

Just add more fuel to your deceleration areas on you fuel - base table. Add like 10-20%

[@Ryan-op9bk]

@@CanyonTuned thank you man

[@patrykzmuda674]

sadly i did all of it and it still dosent shoot/pop well i tried ye i did watch part 2

[@CanyonTuned]

Do basic functions like raising your Rev limiter work? A lot of people make the mistake of not sending the "write" signal to the ecu explained in the first part

[@j.s.4544]

the definition files dont work

[@CanyonTuned]

Then you have the wrong definition files for you specific dme

[@j.s.4544]

Where do I get the right ones? 😭

[@MikeP41]

@@j.s.4544 rom Raider forums make sure you make an account first though

[@juancarlospreciadovillasen1543]

Como cambio alpha n?

[@CanyonTuned]

You need the custom ms41.3. It's on the ms41 wiki page

[@diniselmani4518]

all i hear is "ummmm" hahaha but thanks man❤️

[@CanyonTuned]

This is when I first started youtube lol it was rough at the beginning

[@maythom]

Hello, do you have Instagram by any chance?

[@CanyonTuned]

@armonic0 and @Project.a.z

[@HakenE30]

HakenE30 supports this

[@Diff.Grenade]

Part 2? :)

[@CanyonTuned]

After my e30 is done I'll do a pretty in depth part 2 😉

[@Diff.Grenade]

@@CanyonTuned ayeeee

[@approximatelybored]

Great vid but please write s script and STOP SAYING “aaaammmm”

[@CanyonTuned]

I know, this was one of my first videos lol

[@CanyonTuned]

Part III is here! kzbin.info/www/bejne/iJXGZIJrhc-srZY

[@supabiscuit]

So many ODB's so far in this video. It's OBD. On Board Diagnostics

[@CanyonTuned]

Very minor error, i'm sure everyone knows what I mean

[@supabiscuit]

@@CanyonTuned agreed 💯.... Just had to mention it for whatever reason. No disrespect intended and I appreciate you sharing your knowledge/ experience. .... subscribed because of your reply

[@CanyonTuned]

@@supabiscuit Message me on Instagram (same username) or comment here if you have any questions. This is a pretty old video and i've been meaning to make an updated one

[@E36_kidd]

Can you use this to tune a turbo e36?

[@CanyonTuned]

Yes, you just need to run a 540i MAF or do the resistor mod on the stock MAF. You can check out the rom raider forums for details. I believe some people also run MAFs from other cars (the 350z one is pretty popular) and scale/calibrate it in your tune

[@E36_kidd]

@@CanyonTuned ok, thanks