@@DreamitBuildit I agree, I have watched 20 minute videos that explained less!
@dannyroldan5493 Жыл бұрын
Thanks understood u more than anyone else
@DreamitBuildit Жыл бұрын
glad it was helpful!
@jimmyyounger6187 ай бұрын
I just pulled mine out of the case after years of sitting unused and thought hmm, been awhile. I wonder if there's a refresher for these on KZbin? Thank you!
@DreamitBuildit5 ай бұрын
Glad it helped!
@RickyD1968Ай бұрын
Awesome video !!!
@wandalo9247 ай бұрын
dude your amazing I just discovered channel your videos are very very helpful.
@DreamitBuildit7 ай бұрын
Glad to hear it!
@SixaughtSix3 жыл бұрын
Nice job on the video
@DreamitBuildit3 жыл бұрын
Thanks! Hope it helps.
@parwezfaizi Жыл бұрын
Thank you, very helpful
@DreamitBuildit Жыл бұрын
Glad it was helpful!
@iamhulkbanner39892 жыл бұрын
thanks for the video
@DreamitBuildit2 жыл бұрын
Hope it helped!
@iamhulkbanner39892 жыл бұрын
@@DreamitBuildit it sure did! Thanks again :)
@jamesjohnston5479 ай бұрын
Thanks for getting out of bed for that. Well done! 😂😂
@terrim.6027 ай бұрын
How do you use it to make sure posts are at the same height?
@DreamitBuildit7 ай бұрын
Same method as shown, I would just set it where the laser will hit the top of the post. I’d they’re already set, you can mark where the laser hits and cut the top off.
@imaslowlerner2 жыл бұрын
Thanks, I have plans on building a retainer wall. At a thrift store today 6/15/22 and found one in the case complete and it works, $50.😍
@DreamitBuildit2 жыл бұрын
Great deal!
@lnolt9805 Жыл бұрын
My receiver beeps at random even when I am nowhere near the correct height. Sometimes it gets so bad, it just beeps continuously at any height and I can't tell when I am in the beam or level. Kind of as if it gets interference even though I'm in the woods with nothing around. Has done it randomly since new. Any ideas?
@DreamitBuildit Жыл бұрын
Good question. Not sure on that. For us, if we reset the calibration it usually fixes that. Other than that I'd check the batteries or contact the manufacturer/ seller.
@MR.PRESIDENTOFFICIAL8 ай бұрын
but what if you want to measure beneath the surface?
@DreamitBuildit8 ай бұрын
Not sure what the situation is, but that pole with the receiver can be adjusted quite a bit. You just have to be able to make visual contact with the laser.
@Natedwebb7 ай бұрын
I am digging a pool, so I need to dig down 44 1/2 inches. So i take my measure stick, and I find level for the top of my pool wall. Then, I move the laser reader up the pole 44 1/2 inches. So once I dig down 44 1/2 inches, it will register level again at my reference point, which will be at the top of my pool wall.
@kgarlow62332 жыл бұрын
Do a garde video u will be surprised
@DreamitBuildit2 жыл бұрын
What's a garde video?
@juanmagallon18462 жыл бұрын
Is it a good laser level?
@realmiamiunderground2 жыл бұрын
$ 🎉🎉e🎉Eden 🎉e i🎉🎉e
@jamaya61 Жыл бұрын
Jajaja all 3 of our followers
@elizdan26 Жыл бұрын
I'm building a pool
@tbirdage2 жыл бұрын
Like ya said, that’s kinda how you use it. I was hoping you were going to tell us how to use it on a slope instead of what I figured out in 5 minutes on my own
@DreamitBuildit2 жыл бұрын
Yep, we used it just a bit on a slope when we first started our septic field, but mostly for prepping this foundation.