►SUBSCRIBE / @drivetunemedia Some techniques which will make the process of wrapping your exhaust manifold/header/pipes much easier. Courtesy of DEI.
Пікірлер: 78
@SABRECRAFT11 ай бұрын
Thank you, i’ll be trying this on my new headers tomorrow!
@SABRECRAFT11 ай бұрын
i just finished putting mine on, my forearms are dead but it was worth it
@elxwell165 Жыл бұрын
always start from the bottom going up. that way the seam is beneath to the next seam going up. that keeps the water out.
@Edgonsantrang5 жыл бұрын
I used high temp silicone at the tip of the end of the wrap to keep it from becoming undone.
@Ski.the.slayer Жыл бұрын
How has it held up with the silicone. Did it give it a clean look?
@Edgonsantrang Жыл бұрын
@@Ski.the.slayer the silicone became crispy, but the weave has not come undone.
@scowlsmcjowls26269 ай бұрын
For clarity purposes you should of said sewn edge exposed. That way regaurdless of direction or facing it would be clear what to do
@michaelsnyder57734 жыл бұрын
All I can say is I wish I used gloves
@salomonkarr79173 жыл бұрын
😂
@vitkubal273 Жыл бұрын
😂😂😂
@jamesflores11468 ай бұрын
Savage 😂🤣😂
@evildeed90s10 күн бұрын
me too but i was already done before i realized my mistake
@3li_u3e4 жыл бұрын
مشكورين اخوانا الاجانب
@therealrealshocker Жыл бұрын
Thank you for sharing this 🙏🏼
@brandonbennett78658 ай бұрын
Well, turns out I did my one pipe completely wrong, looks like I'll be redoing it tomorrow and hopefully it goes a lot better. I started at the flange and not the collector, not sure what side of the wrap is where, didnt fold it over at all before my start, I pulled the entire roll through every time so I didnt measure it out, I'm pretty sure I overlapped way too much and needless to say, I'm gonna probably need more ties
@dannyc42002 жыл бұрын
why you need sawn edge to the collector?
@Grandpasaab4 жыл бұрын
is this doable when the manifold is mounted? my studs are very rusted and dont really want to undo it
@DriveTuneMedia4 жыл бұрын
Depends on the header, probably doable, if you're patient....
@isaiahtrap33352 ай бұрын
Will 50ft be enough to wrap both headers
@DriveTuneMedia2 ай бұрын
www.designengineering.com/calculator/
@harryleelhyli26542 жыл бұрын
can such wrap reduce resonate?
@bluegill20307 ай бұрын
What was the screwdriver for?
@CamboSlice-3 ай бұрын
great question.
@_bloc103 жыл бұрын
This should keep the heat down in the engine bay?
@kino2663 жыл бұрын
It will help, but if your engine is overheating on normal riding and normal weather, there are problems that wont be solved with exhaust wrap. It could help a bit when you have hot weather and are driving in traffic all the time
@thatoneintrovert96184 жыл бұрын
I have a cover on my manifold. How should I remove it?
@skyty03 жыл бұрын
A little late, but... Assuming that you have a stock header, that is a heatshield. It does the same thing as a wrap. Do not remove it lol
@thatoneintrovert96183 жыл бұрын
@@skyty0 I'm assuming the entire manifold is plastic. I have a 2012 Fiesta so I don't know if the intake manifold is completely plastic or it's a heat shield like you said.
@tylerhanincheck49283 жыл бұрын
Why has no one mentioned the smoking? Is that normal? Also can you use this in place of a heat shield?
@DriveTuneMedia3 жыл бұрын
They smoke for the first few heat cycles. Yeah, I think you can use them instead of a heat shield.
@TrocasMX2 жыл бұрын
Why wrap up to the head when you can wrap down to the tip and ti will look cleaner 🤦🏿🤦🏿🤦🏿🤦🏿🤦🏿
@Ozarkprepper6432 жыл бұрын
I watched hoping to see how to start the wrap. Both times you neglected to finish showing the beginning
@TonyTheTruckGuy4 ай бұрын
Are you blind? 1:10…
@stevenpapa33065 жыл бұрын
Can u wrap headers that are heat coated
@pg24mvp744 жыл бұрын
If they’re ceramic coated I wouldn’t bother wrapping again
@Motleymick3 жыл бұрын
@@pg24mvp74 But why not? Wrapped headers looks so cool. And it's cheap to do.
@azegulstarrider96753 жыл бұрын
You can. Some people do.
@punto14103 жыл бұрын
silly question: What would be the weight gain for such a wrap?
@DriveTuneMedia3 жыл бұрын
Minimal. DEI "Titanium" is very light. Exact numbers I don't have but it's lighter than normal fiberglass wraps.
@HondaAccordPerformance3 жыл бұрын
@@DriveTuneMedia I’m worried that I might damage my headers I used a lot of overlap like 1” because I used the 2 inch wrap on mine I might of over did it. Should I remove the headers and rewrap them?
@jagmeet948 жыл бұрын
will the wrap lead to rusting of pipe?
@DriveTuneMedia8 жыл бұрын
Hi., If its mild steel, yes. Stainless does not rust. Should not be used on Titianium exhausts because they tend to have very thin walls.
@nyinfamous2k27 жыл бұрын
how about if the pipes are painted with high temp paint first before wrapping them? would that cause or help any rusting issues? thanks
@firgaso6 жыл бұрын
StreetandCircuit o
@hyp3MC6 жыл бұрын
nyinfamous2k2 I’m curious in this as well.
@ReaDKingS5 жыл бұрын
Yes, because it retains water and the dirt and grime from the road. Look at the pipe he is wrapping. Ir was wrapped at least once before... looks like the wrap stained the exhaust... you should change the wraps every 6 months or so.
@pufflopez28963 жыл бұрын
How much ft do I need for those headers ?? Is 100ft enough ??
@DriveTuneMedia3 жыл бұрын
Here is a calculator for exhaust wrap www.designengineering.com/calculator/
@josepeixoto33843 жыл бұрын
is that made of painted/tinted fiberglass +
@DriveTuneMedia3 жыл бұрын
crushed lava rock is the main material.
@TheShangralaaaa175 жыл бұрын
Those metal ties dont stay tight at all....they're worthless
@Boofedit4 жыл бұрын
TheShangralaaaa17 after 12 drives or so the heat should’ve solidified the wrap into place anyway?
@deathtoliberals78434 жыл бұрын
Use barium coat wrap.
@BlackMirror_fk89 ай бұрын
So you don’t need to wet it first?
@DriveTuneMedia9 ай бұрын
Genuine DEI Titanium is very flexible without water.
@dustylooney92363 жыл бұрын
I learn one thing wrapping my headers WEAR GLOVES .
@polasnoob3 жыл бұрын
i just get itchy right now 💁🤦 i feel regret
@slicktop2jz8553 жыл бұрын
Exactly! My hands are a mess.
@polasnoob3 жыл бұрын
@@slicktop2jz855 😭😭😭✋ at first i thought it just like a normal cloth
@andyroo30222 жыл бұрын
Ha, I had a practice run of one of my Beetle J pipes last night. Until I read this I was wondering last night why my hands were itchy. I thought that only happened with fibreglass.
@josepeixoto33845 жыл бұрын
where is the titanium? is that basalt?
@DriveTuneMedia5 жыл бұрын
Hi Jose. Yes its Basalt. Titanium is the name of the product, does not refer to the materials
@Motleymick3 жыл бұрын
@@DriveTuneMedia That's Confusing. I bet they did that as a marketing trick.
@CamboSlice-3 ай бұрын
@@Motleymick yeah total bs why would you call it titanium in the first 10 seconds of the video and say that it doesnt need wetted down like fiberglass wraps, because "this wrap is titanium" lmao
@Boofedit4 жыл бұрын
And now...simply wait 6 months and replace entire exhaust side of the engine!
@MaRkiLLeR6664 жыл бұрын
Why?
@Boofedit4 жыл бұрын
MaRkiLLeR666 in my experience, heat insulating wraps do more damage than good in the long run if you live in high humidity areas, cause early rusting and corrosion, weakens the metal. I get it though, hotter gas flows better, less heat dispersion in the engine bay, seems ideal but for most geographic locations in the Southern Hemisphere it’s more than un ideal, hope that clears up my reply :)
@vally68534 жыл бұрын
themusicmastera380 gotta spray the wrap with silicone to deter water
@bulbazoth6473 Жыл бұрын
titanium doesnt rust@@Boofedit
@Boofedit Жыл бұрын
does corrode though! @@bulbazoth6473
@evildeed90s10 күн бұрын
wear gloves very important dont make my mistake
@marlo916Ай бұрын
This titanium shit is still itchy af lmao. Just as annoying to deal with as fiberglass and the weave keeps unraveling and unstitching
@obbzerver4 жыл бұрын
And now you can proudly watch as your headers are trashed by heat and accelerated rust.
@deathtoliberals78434 жыл бұрын
Headers are cheap,compared to damage headers do. We couldn’t keep a starter from burning up,with heat wrap. Headers just get too hot ,under a hood.
@DL101ca4 жыл бұрын
@@deathtoliberals7843 don't wrap the headers, insulate the starter.
@michaelsnyder57734 жыл бұрын
Just get better headers that can take it like stainless and use high temp header primer 3 years on beating on it and still whole.