Today I'm replacing the rear wheel bearings on my GTI Music provided by Monstercat: State Azure - Moth / monstercatsilk
Пікірлер: 25
@RLT5 ай бұрын
A viewer mentioned to me that I forgot to show the exact Torque specs for the center bolt. Torque the Bearing center bolt to 180nm (132.76ft-lbs) then an additional 180 degrees. Hopefully this helps, sorry everyone.
@jakeclark798Ай бұрын
Also, you can do just the caliper pin bolts, you can leave the mounting bracket installed. One less set of bolts to worry about and saves a little time
@jshade97525 ай бұрын
Thanks. 107kmi and rear wheel sounds.
@RLT5 ай бұрын
You got your moneys worth out of that bearing
@jonnyvt66029 ай бұрын
Never put the tyres with the least grip on the rear, unless y like going backwards into a hedge!!
@jakeclark798Ай бұрын
Tried to do the 180° after torquing, I got 90° and broke my breaker bar with a jack handle as an extension on it. Just gonna send it like that 😂
@RLTАй бұрын
Your breaker bar said “close enough” 🤣
@brandenmeadows42864 ай бұрын
90° pick works great.
@erniealvarado4517 Жыл бұрын
Great video !! Very informative as well. Keep the gti videos comming !! New subscriber!!
@RLT Жыл бұрын
Thanks for watching! I’m glad you are enjoying the content!
@MLeung-vl7we10 ай бұрын
Thats it? Which brand bearing did you get? Big price difference between Viaco vs. SKF (OEM) at FCP. When you say star bit, is that the same as triple-square. What size was used for the bearing nut? Thanks for the video, gives me confidence to do my 2016 MK7.
@johnturner63403 ай бұрын
What size spline for centre bolt is it
@jakeclark798Ай бұрын
18mm triple square
@TheRallyCoop4 ай бұрын
The manufacturer states do not rotate the tires
@RLT4 ай бұрын
Dealer probably recommends not rotating tires. I haven’t seen VW specifically mention it. Plus it causes no harm as all the tires are the same diameter and width.
@Propilotgill11 ай бұрын
Nice!
@TheRallyCoop4 ай бұрын
They are called triple square.
@RLT4 ай бұрын
I hate when I know a word and it just will not come out when I need it. Thanks for the assist 🥲
@zachel Жыл бұрын
How long did this take you? My shop is trying to charge me for 3 hours for 1 side.
@RLT Жыл бұрын
I would say probably an hour of activity working. Realistically it took me 2 hours because I was trying to make a video but it wasn’t really that much work itself.
@jonnyvt66027 ай бұрын
Hi, what torque value do you use??
@RLT7 ай бұрын
Which specific part do you need the torque value for I believe I named a few
@carscloseup5 ай бұрын
@@RLTProperly the wheel bearing bolt torque. It has to be torqued to 180 Nm and then 180 degrees. You definitely didn’t do that.
@RLT5 ай бұрын
@carscloseup I did after the video. I forgot to video the 180 degree part.
@RLT5 ай бұрын
@@carscloseup I have Pinned a comment with the correct torque spec thank you so much for letting me know I left that off. Sorry about that.