Samsung washing machine stuck on program? Fixing intermittent fault & PCB (Printed Circuit Board)

[@tetleydidley]

This video has been really helpful. I got a UC error on my unit WD10J6410AX/FQ (Samsung says that's due to irregular voltage). Back in 2020, I contacted their customer service and they blamed it on poor electrical circuitry of my house (it wasn't). Thanks to this video, I gathered enough confidence to finally open up my washer-dryer unit myself. I had 0 electrical/electronic works experience. Anyway, I visually inspected the insides and I was shocked, not by runaway electrical current, but by the poor internal design. Cables and connectors are not protected by corrosion. I felt with my hands the brown insulator block? (cardboard? ceramic? clay?) that's located in front of the drum and it was damp! The unit has at least 1 hole that mice, lizards, insects can easily crawl into. The hole looks like a convenient place where you can hang the water outlet hose too - and when you've used the machine long enough, that hose is going to have residual detergent that will drip into the unit. So the occurence of corrosion or electrical faults on this machine is really just a matter of time. I then visually inspected the resin-filled mainboard (I'm just going to say resin, it's plasticky, doesn't appear to be pliable). I saw discolouration near the connector holes on the PCB (where wires are joined and soldered behind to form a complete circuit). That might be due to rust - they look brown to me. But can I know for sure that they are the ones causng problems? No, because the entire PCB is "protected" by said resin. I can't take the PCB out from its housing without also breaking the resin "seal", a term which I use lightly since it clearly isn't moisture-proof. The seal also means I can't perform any meaningful diagnostics. All these factors lead me to conclude that I should just call time of death for this unit. I've already spent the equivalent of 200 pounds getting the drum replaced last year. I can't spend an extra 200 pounds for a refurbished PCB that I won't know for sure will solve the issue right? Looking at the cable mismanagement of this unit (the general messy layout and the inadequate insulation at the terminals in an operating environment that's damp), it's very likely that other circuits could be compromised as well or soon would be. And I just don't want to deal with individually checking them. It's just easier for me to elect to not buy Samsung anymore. And I haven't since 2020. My current washer is a Bosch. I just bought a gaming monitor that's an LG. My air-conditioning unit is a York. My NVME SSD is a Western Digital. I'm going to get a Sharp or a Toshiba for my fridge soon. And for the first time I'm seriously considering getting an iPhone to replace my Samsung Galaxy smartphone. Anyway, I hope you continue doing this good work. It helped me to finally lay this issue to rest. I truly appreciate you sharing your knowledge here and I know others do too.

[@How-to-repair]

Really glad I was able to assist you in diagnosing the problem with the machine and thank you very much for the super chat. Please remember to subscribe to the channel as that is what really helps us glad we could help you @tetleydidley this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@How-to-repair]

A while ago on KZbin, you ask me a question about your LG washer. I just thought I’d let you know that I have now made a complete playlist to assist you in any repairs that you ever have. If it helps, you don’t forget to share it with your friends who may also own an LG. kzbin.info/www/bejne/rWbHi2eGn519mtE

[@LumenoFernandes]

Thanks to your video , I was able to replace the PCB with a second hand one from EBay for 45£. Samsung were charging me £108 for call out charges and £175 for the PCB !

[@marcus19128]

Just did this fix on my machine with the same symptoms and it worked perfectly after installing the relay. Have to say getting the old relay out was a bit of a job and I had to cut out the plastic to get to the soldered joints but it worked OK. Thanks Dean saved me a couple of hundred pounds👍

[@janetldonnelly]

Brilliant stuff! My Ecobubble was stopping at random times in random programmes. Some programmes were okay and some got a minute or 4 mins in and then the drum would look like it was struggling to turn. I knew that the problem wasn’t with the drum as it would turn fine in some programmes. I did the dignostics and everything else was fine so narrowed it down to the motherboard. Found a complete front fascia complete with motherboard on eBay for £35 and fitted it in ten minutes. Just the one big connector to swap over. Took me longer to get the top off and the soap drawer out! Your videos are brilliant as I wouldn’t have had a clue without it and maybe resorted to buying a new machine as I wasn’t going to pay £200 quid for a new fascia/motherboard and then pay to have it fitted!

[@How-to-repair]

I'm glad you managed to get it sorted and I'm glad the video helped

[@s1dew1nd3r4]

have a question for you sir - so i have one of these eco bubble machines, had it for around 6 years now and its been brilliant.. however just these last few days, its started to not turn on after completing a cycle, its just literally completed a full "daily wash" cycle fine and now when iv gone to turn it on to do another wash its as if there is absolutely no power to it, its been happening on and off for a couple of weeks now, i can plug it in/out a few times and you hear it come on eventually or sometimes just not at all - il leave it for a bit an go back and itl come on, any ideas as to what it could be?@@How-to-repair

[@robertopiazzoli5307]

The problem is the bad soldering of the Mosfet and power connector under the dissipator. Remove the glue and reniew the solder dot and fix it for 0 monay. I had the same problem on the same board......TOTALLY SOLVED

[@How-to-repair]

Glad my video helped and you were able to fix your problem mate. Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks, Paul 👍

[@CraigMilesYoutube]

I'll have a go, thanks.

[@marc.lepage]

I was finding our washer intermittently failing to progress mid-cycle, and also occasionally giving error 3C (motor RPM sensor I believe). Sometimes it would pass the self-diagnostic, sometimes immediate 3C on the spin test. Continuity test revealed one of the wires in the cable from the control board to the RPM sensor was faulty; I replaced just that cable, and the 3C error seemed to go away. Still getting failure to progress sometimes though. Guess I need to investigate more, before considering replacing the PCB.

[@Ronnycoop1]

Thanks mate, my daughter's machine locked up to one program and stuck on 51 mins, fault remained even after unplugging for a day. The two button and power procedure brought up diagnostics. Had no idea what I was looking at, so turned it off and on again, now all good. Thanks again

[@How-to-repair]

Glad it helped Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@nasicher6773]

Super Anleitung ! Ich hatte schon selbst Reparauren an meinem Trockner versucht und war erstaunt über das Silikon auf der Platine. Daran ist es nicht möglich was zu reparieren,das Silikon geht nicht runter. Ich dachte das wäre nur an einigen Geräten so,aber scheint ja generell an jeder Maschine von Samsung zu sein.. trotzdem gute Anleitung,weiter so 🙂

[@How-to-repair]

Das ist sehr nett von Ihnen, ich versuche nur, auf die richtige Art und Weise zu unterrichten, die jeder versteht. Das Hauptziel der Hersteller ist es, Geräte zu verkaufen. Sie nutzen grüne Marketingtaktiken zu ihrem Vorteil, werden aber nicht für den wachsenden Haufen ausrangierter Haushaltsgeräte zur Verantwortung gezogen. Heutzutage halten Maschinen im Durchschnitt nur noch etwa fünf Jahre. Es wäre wirklich hilfreich, wenn mein Video geteilt würde, um uns im Kampf gegen die Verschwendung von Haushaltsgeräten zu unterstützen! Bitte vergiss nicht, unseren Kanal zu abonnieren, denn das hilft uns wirklich 😇

[@markrowley5497]

Hi I think my spider and bearings are crackered and the drum is clearly spinning making it worse. I saw your video which was fantastic, it seems I could replace the spider and bearings but the plastic drum by the door is getting damaged. If I replace the Spider and bearings would I need to replace the drum? or would you recommend a new machine. Thanks very much.

[@elanad7356]

Thank you!! All your videos have a wealth of solid information and advice... my machine is broken and I now have the confidence to try and fix it. However, I may be naked doing so (TMI..I know) I'm elderly , have 3 grown sons"existing"at my home... leaving everything for me to "try"to repair. They'll deserve the sight they can't erase!😂😅

[@carigwin9987]

🤣😂

[@jackiewillocks7471]

Ohh you've made me laugh so hard! 😂😂

[@Charlie_Crown]

🤣🤣🤣😆👍

[@RikHewis]

Very helpful - one comment, the video suggests using a hook to remove the stuck plugs but, at least on my version, the retaining clips need to be pushed in, rather than pulled out; so a pair of needle nose pliers might be more use than the suggested hook.

[@How-to-repair]

Thanks for sharing your insight mate. Since I have na access to your washing machine, I can't make a comment about it but if you say so, t's better for you to do it with your way. Could you also do me a favour and take part in a poll I've made about the lifespan of appliances if you havenot already? You just need to tick one of two boxes. It will only take about 10 seconds. This might help us improve how machines are made in the future😇 Here's the poll question: www.youtube.com/@How-to-repair/community Also sharing will get more people to participate and we will have a greater impact with the manufacturers thank you for helping.

[@RuanBotha]

You sir, are my hero. My wife looks at me with admiration. Thank you!

[@How-to-repair]

Fantastic mate! I'm happy to my video was helpful to you. Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks 👍

[@retrospeed560]

Thanks to this extraordinary dude I’ve fixed my Samsung by replacing the pcb....fantastic thanks

[@Roadkill7878]

Thanks for this invaluable video. I got PCB out and got code. I have ordered a refurbished part. Couldn’t have done it without your help. Great result, saves money and reduces landfill 👍🏻

[@How-to-repair]

Glad it helped Roadkill7878 the easiest techniques to find parts of the best I would love you to leave your opinion on our poll about manufacturers building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@Roadkill7878]

Just an update. The new PCB solved the problem and machine is now like new 👍🏻

[@Tom-yu1nh]

Hi, a quick question. Can I replace RDFC-2716 with 2717? The latter has double R comparing to 2716...

[@deannaporter1749]

Thank you for the valuable video. I successfully replaced my control panel and it worked perfectly. I used eBay and paid less then 50 with shipping and tax. Great deal! Thank you so much! Was really pretty easy to do.

[@How-to-repair]

Really glad you got it fixed, saved a load of money and you have managed to recycle and appliance that would normally go to the tip. Well done. glad we could help you Deanna Porter this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@carmelopiazza5159]

Complimenti per il tuo modo esplicativo ed esaustivo,ho un grande problema la mia lavatrice Samsung WF 906P4SA NON SI ACCENDE PIU'.Dopo avere controllato i collegamenti alla rete , ho testato il filtro antidisturbo ed è funzionante.Questa lavatrice ha due schede elettroniche ,una posta sul frontale (scheda comandi) ed una posta in basso vicina al motore (scheda potenza),secondo te quale delle due è guasta?

[@How-to-repair]

Ciao Carmelo, ho creato una pagina di FAQ per te. In questa pagina puoi trovare una guida dettagliata per la riparazione del tuo problema. Poiché la mia lingua madre è l'inglese, non sono riuscito a spiegarlo in italiano. Tuttavia, è possibile utilizzare il traduttore per leggere la mia risposta. Ecco il link: www.how-to-repair.com/faqs/samsung-wf906p4sawq-washing-machine-no-longer-swings-on/ 😇 Dato che lavoriamo molto duramente nel nostro magazzino per realizzare video-guide gratuite per tutti voi sugli elettrodomestici, apprezziamo sempre una birra, offrendo una scelta di birra singola o rotonda. www.how-to-repair.com/help/buy-paul-a-beer/ Ricordatevi di iscrivervi al nostro canale, perché è questo che fa andare avanti il canale. Grazie, Paul 👍

[@MilindKadam2011]

Your are a core person of product understand technically. Your doing really nice work to guide tech and support very clearly and small small things your explain . I like the way explain and i am a fan of yours . I am from india also repair everything every electronic products . Same way always i try to explain with anyone. I wishes for your channel to grow more and more Sir 🙏

[@sashakupetsky]

Hello and thanks for the video. Can you tell me, please what pin on CPU D78F1146A on this board is door_check? Or where to find the schematics? dE error. Door luck, wirings - OK. Thanks.

[@sarockpashotan]

Hi dear master.it is a very good channel for learning how to fix washing machine for me.thanks alot. From iran.

[@skwallace]

Thank you Paul - I have successfully replaced the PCB and motor on my Samsung EcoBubble 8kg machine. Enjoy the beer!! Live long and prosper.

[@rheadog9546]

such a complicated way to pronounce aluminum. hehe....I agree totally, and you are a breath of fresh air when you say we need to repair these machines. Most people love their machine they have used for 5-10 years or more an the last thing they want to do is buy another brand new machine and deal with disposing a good machine they loved that has a simple bad part that could be easily fixed, but can't see paying to repair it when a new machine is $200.00 more. This has gotten out of hand lately and it's nice to have people here to help that actually care.

[@How-to-repair]

I totally agree, built in obsolescence will be the downfall of this industry have a great Christmas and a happy New Year glad we could help you @rheadog9546 this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@mikus2512]

Brilliant, found a cheap PCB swapped it in and we're back in business! Thanks for the vid!

[@How-to-repair]

really glad this helped you please remember to share our site on your social media as that's what keeps us going and thank you for subscribing

[@mikus2512]

@@How-to-repair Do you think it would be worth me offering my faulty PCB out for potential repair? It just stopped powering on - I imagine someone out there might be able to fix it. (I don't need money for it)

[@aamirnawaz5084]

Hi my Machine saying DC error I have check look but still same . if I replace the second board, the one is doing in a video.will sort the issue?

[@harryboi4313]

I've been looking for this kind of video for months now. Just need to find a circuit board 😂. Thank you 👍🏽

[@How-to-repair]

Hi thanks a lot for your comment and I'm glad it helped. It would be really helpful for me to get my video shared and help us fight appliance waste! Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks, Paul 👍

[@spiritualbohemian]

Fantastic channel. Bravo for the great videos. We need more folks like you to save the waste of unrepaired appliances. Thanks so mich for the help,

[@tobiasripper4124]

hey, maybe you can scratch my curiosity itch. im dealing with a samsung 1904, pretty much the same pcb. this one has an issue where the drain pump is not getting current. weirdest part it is, it tests 220v (we use 220v here) between either pump terminal and 1 of the line terminals from the power cord (writing this i realize i should have chekced if it was line or neutral, but does not change the fact the both pump terminals are testing 220v against one line "pole"). im pretty much giving up on that board, but im very curious as to why im getting this measurements. in fact, at some point i got 110v at the pump terminals. that was one time thou. so yeah, im betting on a busted board.

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks 👍

[@Leo-gt1bx]

Hi what other than motor would prevent this machine from turning over in any mode? I can't even seem to get it into diagnostic mode

[@ramidindar3139]

Usta elinize sağlık bu pcb nin tamiratı yapılsa olurmu röledenmi kaynaklı yoksa triyak tanmı..

[@How-to-repair]

Evet tamirat yapılabilir ama bu tarzdaki Samsung kartlarda tamirat işlemi yapmak çok zor olur çünkü samsung kartlar genelde tamamen silikonla kaplanmış durumda oluyorlar.

[@michaelbaskinmichael9862]

I have a vet I just moved and it’s like new but when we started it screen was red line flickering but it was working what could it be need a reset

[@propheticdancer8675]

Thanks for good explanation on how to come up with a better solution without costing a lot.may God bless you more sir

[@thehypest]

I can't get the top cover off after removing the back screws. I even plied the two metal "lips" on the side that keep the lid down trying to open it. Is there anything on the front that needs to be unscrewed/unclipped? It's the same model as the one in the video WW80J5555MW/ET

[@ianbartlam5338]

Thanks for the video, bought a new pcb and was an easy fix. Much better than scrapping it. Well put together video thanks

[@How-to-repair]

Great to hear! All I'm trying to do is teach in the correct way that everyone understands. It would be really helpful for me to get my video shared and help us fight appliance waste! Please remember to subscribe to our channel, as that really helps us 😇 I'm also employing someone now to assist me in my workload. You can support us by donating to our website www.how-to-repair.com/help/buy-paul-a-beer/ I will continue to invest the beer donations that I receive predominantly into the new video technology that I'm learning with tracking cameras and better audio to make it easier for everyone to understand 🔋

[@ianbartlam5338]

@How-to-repair I'm from an engineering background. I will always try to repair before discarding. It was the simple diagnostic procedure that clarified am already sure fault. Part instalation was easy with plug and play connectors. At one point as I was testing the progression. Thre was a slightly pulsing in the spin tone and I thought it was a motor issue. But it cleared and success. So thanks for the information.

[@chapatizalafolie]

Hi, I have something similar. My machine is stuck at 9 mins but when I ran the automatic test mode, I saw that at the 10th step (which unlocks the door) it doesn't unlock and I immediately have the error code "SF" If I reboot and redo the test mode, at the step one (where's the door locks) it doesn't lock. I removed the lock mechanism and everything seems perfectly fine. SF in the manual means Main PCB error... Should I change it or I need to check something else before doing that ?

[@keithwheeler3049]

Thank you for this video, you’ve saved me having to buy a new machine. I managed to source a reconditioned pcb which I fitted this afternoon, all good so far 😊

[@How-to-repair]

Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@paulgrime]

Thanks, fantastic work. Have ordered a refurbed part. Love your environmental message, keep it going!

[@trev2417]

Brilliant videos,I think I’m gonna have to buy a new machine at the end of the day, I’ve watched a good few of you videos on the Samsung eco bubble and definitely won’t by another Samsung.

[@Richard-m8l]

My unit eco bubbles 7.5kg have the display but not working.. Even I reset not spinning. Can you tell me what is the problem.

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@syedaismatara1990]

Hello Sir, my machine is Spin cycle, which is a problem because when 9 minutes, then again start 17 minutes.

[@LearnFastic]

Great tutorial, many thanks for sharing your experience and for all the hard work to produce the video. Keep up the good work.

[@bernardrooney6563]

I changed the 2 shocks in my Machine first. Which cured this stuck timer issue, cost about £15 quid. must have been the unbalanced load disrupting the cycle.

[@CHOPPA78]

Hi there i have an eco bubble washer dryer , once drying the drying cycle is finished the laundry is saturated and hot the pump is working and the filter is clean , it pumps fine on a washing cycle i am at a loss as to why this keeps happening could you advise please ??

[@realldonaldtrump]

So how does the PCB go bad in the first place?

[@MilindKadam2011]

Every PCB have memory built with program inside pcb any of components fail its cause impact on program or program may be corrupted . Every cycle have step by step process one after one if sequence miss it's stuck line your windows OS not boot because your OS or HDD failed.

[@Limited_EditionUK]

Thank you for sharing the video. You have done a great job for many. It’s very helpful. Well done sir 👏👏👏

[@jesserawson898]

If only there were more channels like this that encourage the use of second hand parts etc. Grab the health and safety aspect firmly by the testacles and throw that in the garbage bin, together with the "fear" exponents of the "H&S trumps everything" try to get us with. A very worthwhile video brilliantly presented. Thank you so much.

[@RuubRoyce]

This is a common known defect on the ecobubble. In most cases it will not complete the centrifugation cycle, or even start it. The chips on the controll board deliberately have a very limited lifespan as they overheat due to the way samsung designed the PCB. Planned absolescence if you ask me. Ordering a used one, will therefor again only last you a limited time. Buying a brand new one will set you back 200 Euro's. That's almost half the cost for a complete new ecobubble. I'd stay far away from the ecobubble. Should you decide to buy one regardlessly. Buy the extra warranty, as you're gonna need it. Or since you're gonna spend that extra money anyway, just buy a better brand. Miele, Bosch, Siemens, AEG. They cost more on the short term, but will save you money on the long run. All washing machines will wear down on mechanical parts eventually. But they shouldn't fault that easily, let alone on non- replaceable roms. And not at all within three to four years, which is not long after the 24 month warranty.

[@DavidBeckett-dn2ig]

Hi ive got the same problem on the same machine in the video. Mine wont go into diagnostic mode though, any thought's. Thanks

[@Lotuslovable]

Should I do this if it shows UC error code? Recently we had a lightning strike to our house with many appliances and circuits blown..

[@KevinGillis-s4p]

This so sounded like my problem on a Samsung WW90TA049AE/EU and I changed the motherboard pcb (new) but unfortunately the same errors persist - won't go into the spin cycle on a wash, or on a drain and spin etc. [I can/will return the PCB].The self test shows the sarcastic smiley face but no error codes. The water pumps/sensors (in and discharge out) all work. I checked the heater element (27ohms) and the NTC sensor. All OK. I replaced the pressure sensor,(£10) checked the tube wasn't blocked. Ensured there was no debris in the discharge/drain side of things, water pressure in is good, So the ancillary bits in the cycle before the spin all seem OK. The drum/motor turns, the belt drive is OK when moved by hand. The motor is a BLDC (Brushless dc) motor. It has continuity across the connector terminals. No brushes to check etc, I have tried the calibration test and it goes through the motions with the led 'circling display' but the drum fails to move at all. So I have ordered a replacement (working/used £30). Waiting to receive that in the post - is there anything else I should consider? Quite a pain to diagnose with no error codes 😞

[@gregzcom1]

I've owned Samsung washing machine eco bubble for 7 years I'm having some issues guarantee run out but inverter states 10 years does that include the carbon brushes? Also probably at stage of replacing but seen your video on rear of drum not fit for purpose and noted many having seal problems and Samsung doesn't seem to want to replace items under warranty so concerned about PCB which mine maybe or carbon brushes. Not convinced Samsung rear of drum, PCB and seal and customer service. So do you recommend a washing machine brand with good guarantee and customer service? Thanks for video I think that's what's wrong with mine but not sure economically worth repairing as it's over 7 yrs old

[@Mike-tv9rk]

So why hasn't Samsung seen the shame and sent free replacements to every owner. This is criminal.

[@Veshremy941]

thanks my uncle will be so happy to fix his washing machines😀😃😃😀😃😀😃😀😃

[@hughshovlin]

Thank you for this video. Have the same problem. When the machine gets to 59 mins on a daily wash it stops or trips the house circut board. However when i did the check to go to test mode i get the -: face. So i feel it is the board that is faulty. But could it be the heater element also? Thoughts PLEASE. Cheers. Ps there is a flashing red key that is constant on the screen?

[@laundrylad1500]

i have a ww90j5456fw, pcb went causing it to skip spin cycles, not tumble on certain cycles and 90c washes we still have to use it every day its a pain but we cant find a pcb

[@nosubtv4242]

I came across this likely issue, i opted not to bother and buy a new machine. It was coming up to about 8 years old and needed something bigger anyway. Good video though.

[@How-to-repair]

I'm glad you enjoyed it @nosubtv4242 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@jas2963]

Thanks for information.i have a DDC fault but have replaced door latch.would you have any idea.thanks for your help

[@iamengineer9795]

The same problem.. Add doors probably don't locking

[@ianbondoc2173]

Hi, thanks for the video! My washer (samsung WW85K5410WW) stopped at 2minutes then it doesn't respond to button clicks anymore, i then just unplugged it and tried to turn it on, it won't. I tried the system reset (unplugged, pressed power button 5 seconds, then play button 5 seconds, then replug) still won't turn on. I suspect it's the same board you're talking about, but before i replace it ($200 in New Zealand), how can i test it to be sure it's a fried board? Can you share a service manual for my model number? Thank you!

[@dannymactheatreoflife.1771]

I would try cleaning the filter at the front and check the grey waste at the back isn’t blocked by blowing down it and then suck the water until it comes to the end of the pipe , it tastes gross so have a beer handy , this cured my after stopping mid cycle 🤷🏽‍♂️🍺

[@Bob_too]

Great Video, I have this problem, but also I occasionally get a 3E error and also occasionally the UC error. I also get the UC error on the tSt setting. I have already changed the Brushes after getting the 3E error. I’m wondering if I should change the Main Control Board, I’ve found a second hand one for £50. Do you think I should take the gamble given the UC error ?

[@DrColg8]

Our machine works on lite or moderate loads. On towels, it won't complete the spin... it starts to attempt to balance spin it but cuts out before reaching full rpms and then the timer resets back to the pre spin time (rinse period?). No wobbles of the drum and appears properly centered concentrically within the doorway space as expected. Unsure why it works on medium loads but not heavier loads, even only two towels. Seems like a balance issue as the pump functions. I find it hard to understand how the balancing ring would fail in a 6 yr old machine

[@How-to-repair]

When you load the drum, it is very important that the clothes are balanced on all sides of the drum. Sometimes the Samsung washing machines can cause lots of problems when you only put one or two towels in as they clog on one side of the drum this, then calls and in balance, I suspect you may either have a problem with the printed circuit boards or possibly if carbon brushes were fitted to the motor you want to inspect these as well. Have a great Christmas and a happy New Year. glad we could help you Dr Sterling Colgate this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@AJ-tp5qj]

Hi i have the same washing machine the issue am facing is that the buttons on the dash stopped working ecept the on/off play buttons so i can actually use the washing machine but cant adjust ant of the cycles (spin , water temp..) any pointers would be highly appreciated Note: Child lock is not on :)

[@Woodkin007]

I'm utterly frustrated with my 5 Yr old Samsung ecobubble. Labour and circuit board will cost around £250.00 just to get the signal going back to the drainage pump. So annoyed.

[@mackkim8618]

Hi Sir, i got a samsung front loader washing machine with direct drive, with less cloth it still can works well, but whenever comes heavier load, it just jam as the video shows. Not sure whether is the PCB issues, but will try to replace. 😀 Another question would be raised as: how to find out the broken parts if diagnose mode shows all is normal ?

[@JohnHamill-k1t]

My machine will not go onto test mode and is doing the smiley face. My machine constantly has red flashing key even when it's off. I've watched your videos and I'm looking towards the motherboard any help before I purchase?

[@FoxyLad]

i have the exact same issues with my Haier washing machine purchased from AO washes are taking longer the spin mode 1400rpm 10 mins it always gets stuck on 8 mins remaining and goes around and around back and forth from 10 mins to 16 mins until it figures out what its meant to be doing and also unbalanced errors during washing I've only had the machine less than a week so haier are sending an engineer out tomorrow i have asked for a brand new washing machine as i have no faith in the model can not ask the engineer not to fix it and get my full refund within my 14 days ?

[@mareksumguy1887]

Hello good sir. I have a Samsung ww75k5210ww. The Cotton programme always starts at 3 hours and 20 minutes… but around 15 minutes into it it subtracts almost 2 hours from the wash time, even if it’s a full load. So I switched to Synthetics programme, which doesn’t subtract time mid wash. However, the water temperature feels a lot hotter than the 40°C that I set it to. It feels more like 50°C! Would this be a PCB fault? Thank you.

[@How-to-repair]

Really sorry for the late reply I was away on holiday. It is possible that it could be the printed circuit board or possibly an NTC sensor not reading the correct value without having the machine on my workbench. It is really hard for me to be able to tell you exactly. I hope you have managed to get it fixed. Thank you very much for subscribing to the channel have a great Christmas and a happy New Year.

[@PeterShears-vs3ko]

My Samsung ecobubble 8kg will not start . The door is locked but the programme dial will not move from wool mode

[@JanizMakudomaru]

My washing machine is a wf45k6500aw/a2, and it is stuck on quick wash; it won't change; the panel is only showing 25min with the hour glass, and then after a bit, it goes into AC6. It does nothing else, and I can't go into diagnostic mode, so what do I do from here?

[@MikeCarter]

did you look up the code AC6 in your printed manual or online? What does the code represent Janiz?

[@stevelogan2042]

I have a Samsung Flex washer that will only drain the water, no diagnostic or calibration cycle. Stopped working with no code. I got it to run a spin cycle one time using the app on the phone. It stopped and gave a code 8C1 code , and the app said check MEMS. Would a bad MEMS stop it from performing any functions. I purchased a new main control board installed and the results were the same. We live out in the sticks with no appliance person with 50 miles. This is the only video on line that is even close to what is happening.

[@guillermopsico]

Great video, best regards from Argentina, I Fix my Samsung machine, Amazing video !

[@How-to-repair]

Hi thanks a lot for your comment and I'm glad it helped. It would be really helpful for me to get my video shared and help us fight appliance waste! Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks, Paul 👍

[@enesemir8214]

Goedemiddag, ik heb een Samsung condens wasdroger hij heef error code TE4 wat moet ik doen graag antwoord en thankyou

[@How-to-repair]

Het spijt me dat ik geen informatie heb over dit modelnummer. Fijne jaarwisseling en vergeet je niet te abonneren op ons kanaal

[@bitsnbobs1969]

i have never got new board scrape that gunk off re solder joints

[@keithpillar7634]

I have same model. I had to press buttons 3,4,5 to get into test mode when switching on.

[@parke48]

Please help me! My screen won’t move at all I click the buttons underneath it it won’t peep the screen only moves when I spin the spinny thing

[@ruthblunt77]

Thanks for the useful videos. My Samsung Ecobubble keeps pausing mid-cycle. I've put it into test mode and everything seems to be working fine. I'm not getting any error codes but it still keeps pausing mid-cycle. Does that mean I need to change the PCB? Thanks.

[@How-to-repair]

I always get a lot of questions like this I can't be 100% as I do not have the washing machine in front of me, but the circuit board is a common problem @ruthblunt77 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@david_eluemunoh]

What did you do to fix it eventually?

[@robertjstrand]

My Samsung top loader is getting stuck at the end of the mode only one some loads and then restarting the rines/sping cycle and just repeats it.

[@iamengineer9795]

You should show if Test program run with new board. Because I had problem with doors DC3 , it lock, run drain pump, then nothing ( drum motor do not run), then unlock and nothing more. It show :- symbol when tried to run Test program too but, later after checking Add door lock it start to run normally. So I am confused with that :- symbol.

[@neilbell2069]

Great video and very clear!! Could you please tell me if it is a PCB problem if the washing machine stops mid cycle? We need to restart it and then it continues where it left off!!

[@How-to-repair]

The first thing you need to do is check all the components I would especially check all the water valves and make sure the machine is emptying in the allocated period of time before pointing the finger at the printed circuit board, but yes, it could be a problem with the printed circuit board

[@midgeycrimbles6730]

​@@How-to-repair hi, i'm eondering how you check the water valves. By any chance have u done a video about this? Many thanks for ur videos, very helpful and love the ethos

[@fill7t1]

Hi, I have the exact same machine, it doesn't spin up to 1400, I can hear it try to step up. Assuming it's the bushes in the motor 🤔, can they be changed easily?

[@How-to-repair]

It will either be the brushes in the motor, or it could be the PCB glad we could help you @fill7t138 this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@mustafizrahman4469]

In this nodel, the no 3 & 4 button indicates for smart check by smart phone. The 4th and 5th button is responsible for test mode.

[@devkantsharma7462]

In my samsung top load machine when I go to test mode it shows LL03 code and not working in test mode and calibration mode

[@michaelgerard4564]

Hello there, Great video! I replaced the motherboard on my Ecobubble WW91J6400CW. Now when I power up the machine, after a few seconds everything starts to blink and there is no reaction from the machine anymore. Any ideas? Thanks in advance!

[@michaelgerard4564]

Video of the occurring problem: kzbin.info8QIBuBeZjEo

[@AyoubAksas-y7u]

I hav Sam problem in my washing machine I just want to Cher with you the video if you can help me to fixed the problem

[@davidhazell8154]

That sarcastic face is what you're meant to point the samsung smart check app at and line it up and use the phones camera to read the fault code - there should be other characters there to diagnose it. I get the same on my machine, no other characters. My machine won't fill or empty and the door stays locked so I'm thinking the main board is shot, but your assumption that the characters being shown indicate it's shot might not be conclusive - a healthy board would likely show the same too. Did you try the same test on the new board?

[@munsterfloyd]

Great video. I just removed my PCB unit. Now I need to order the new one. I do have one question though. Looking through common faults, this is a reoccurring problem with a lot of machines so I was wondering if it is worth getting a used component. It might last a few weeks!!! Any thoughts?

[@How-to-repair]

You would be very unlucky there not bad machines

[@Mike-tv9rk]

You are a great KZbinr. But please just try to show us how to isolate the bit on the PCB that does not work. Show us where to start. I stead of giving Samsung more money.

[@kelseynorrie5651]

can't get my model to go into test mode WW75J54E01W/SA

[@nanushaikh7040]

Hii sir i have samsung 6kg front load washing machine when I set 15 min. Program machine take a water BUT I set other program machine not a take a water inside error 4c is continue What I do sir give me advice

[@How-to-repair]

This is a very hard one for me to answer. I'm sorry as I do not have the machine in front of me. I will check the water valve to make sure that all the solenoids are working correctly. @nanushaikh7040 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@amineelboukhari1487]

Hello sir I m a technicien from Morocco I have a solution that i want to share with you In samsung ecco bubble there's is a problem with connection the most of time the socket of water level that cause the pcb not working problem the most of time the machine stops after a shirt time or stuck in any programme and stop responding if touch any botton So i solve this proplem some time i change the cables or the front pcb witch the socket of water level and it works every time So please check te water level socket and cables , connections and i hop i was helpful as your are Tank you for your time

[@jaroslavferko8312]

how about fixing the driver card novo times of repair

[@How-to-repair]

If you are able to pick up a circuit board at a low cost, then it is not worth messing around with the Samsung boards as they are covered in silicon and very hard to gain access to have a great New Year and please remember to subscribe to the channel

[@SybilDefense]

I hate trashing items into land fills. Such a lazy throwaway world we've become. I often rescue things from neighbors refuge even if I don't need one, just to keep it from the dump. Now with the eV cars that are entirely disposable like huge expensive Bic lighters. They are the least green idea we've had, but the most pushed... all for corporate greed

[@How-to-repair]

I'm putting a link below to a survey I did on obsolescence I would love you to fill it in. The hydrogen car has been about since 1980, but manufacturers will never allow it to become public in the way it should because until they work out how we get charged tax on water I don't think this will ever come to light. Sybil Defense I would love you to leave your opinion on our poll about manufacturers building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@masont8829]

Very helpful video sir keep it up

[@vickibourne6805]

Thank you, absolutely amazing, I too do not want to contribute to land fill sites unnecessarily. If I can fix it, I will certainly try ⭐️⭐️⭐️⭐️⭐️

[@How-to-repair]

I'm so glad my videos are assisting people in solving the huge problems that this planet has with waste and built in obsolescence @vickibourne6805 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@rajkumarjangir1887]

My machine repair dc cimbal what can I do

[@USMCPL]

That frowny face..... Was the new sign for smart control setup.... I scraped a freaking flexwasher with that issue. If you open smart things on your phone it'll interact with it when it has that face on the display

[@Truth_Seeker1]

My Sansung Echbuble will stop, start making noise and freeze on different numbers, and won’t spin :(.

[@How-to-repair]

Hi @Truth_Seeker1 I will need the full model number of the identification plate please use our contact us page and make sure you fill out the request of what part you are after and will get back to you within 24 hours normally www.how-to-repair.com/help/contact-us/ this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@funwithanimals9343]

Hello Sir , my samsung washing machine has no power at all , what could be the issue

[@How-to-repair]

This will either be the door lock the electronic filter coming into the machine, or you may have a problem with the printed circuit board. Have a happy Christmas and a great New Year. please remember to subscribe as that's is was keeps this channel going. Thanks 👍

[@truthseeker803]

Thanks for talking right to repair.

[@LZDEN]

first class work and advice.excellent.

[@How-to-repair]

thanks it's all about setting an example, we can't let manufacturers dictate how long appliance last their built-in obsolescence has become a joke and the governments are letting them get away with it, the average lifespan of a washing machine in 1980 was minimum 10 years and now they seem to be producing junk the only last three

[@oliviamonteque6407]

D,

[@mohdkhairulahmad6701]

How to hot code?

[@adnanahmed4285]

During turning ON washing machine it get stuck in program no function work,there is no child locked after sometime work normal. What will be issue??

[@How-to-repair]

Without having the washing machine in front of me, this is a very hard one for me to be able to assist you